1. Draw a FBD to determine the elbow moment of force necessary to maintain the forearm in a horizontal position. Solve for the elbow moment with the following: subject mass = 75 kg, forearm length = 32 cm. %3D

1. Draw a FBD to determine the elbow moment of force necessary to maintain the forearm in a horizontal position. Solve for the elbow moment with the following: subject mass = 75 kg, forearm length = 32 cm. %3D

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 39P: The forearm shown below is positioned at an angle with respect to the upper arm , and a 5.0- kg...

See similar textbooks

Related questions

Q: 47. || BIO Hold your upper arm vertical and your lower arm horizontal with your hand palm-down on a…

A: The given arm works as the lever. According to the lever rule, Net torque about the pivot point = 0

Q: The tongs are used to grp the ends of the drilling pipe P (Figure 1) Part A If a torque (moment) of…

A: Draw the free-body diagram of the tong.

Q: A person bending forward to lift a load “with his back”(Fig. P8.23a) rather than “with his knees”…

A: Given data:W1 = 200 NW2 = 350 N

Q: (a) Find the tension in the strap. N (b) Find the components of the reaction force exerted by the…

Q: A force of 200 N is applied perpendicularly to and at the end of a wrench 0.4 m long. Compute for…

Q: 12.Based on the figure, assume the somewhat artificial condition that the strut is weightless and…

A: Given, Weight, W = 10 N Tension, T Normal force, N Angle made by T with the horizontal is, 37° the…

Q: Determine the moment of inertia of the cross-sectional area of the reinforced channel about the…

Q: 2. A person's arm is used for ergonomic studies. If the distance of the AB, BC, and CD segments are…

Q: A dental bracket exerts a horizontalforce of 80.0 N on a toothat point B in Figure P8.6. What isthe…

A: Given:Value of Force, F = 80 N

Q: 1. A person holds a 50.0-N sphere in his hand. The forearm is horizontal. The biceps musde attached…

Q: Q12) The figure shows a uniform, horizontal beam (length - 10 m, mass - 25 kg) that is pivoted to…

A: Draw the free-body diagram of the beam.

Q: Why should nails be pointed and not flat on its tip?

A: Pressure is defined a the force acting per unit area.

Q: (II) A person exerts a horizontal force of 42 N on the end of a door 96 cm wide. What is the…

A: II torque can be expressed as

Q: How do I solve this problem?

Q: You can find the center of gravity of a meter stick by resting it horizontally on your two index…

Q: 5. The figure shows a uniform, horizontal beam (length = 10 m, mass = 25 kg) that is pivoted at the…

A: The torque exerted in an object is equal to:τ→=r→×F→where,r→ is the displacement vector from the…

Q: ob.2 Assume that r is much larger than a or b f d then calculate the torque exerted on the squa

A: Suppose that (r) is much larger than a or b. The magnetic field (B) acting on a square field with…

Q: Draw the shear and moment diagrams for the simply-supported beam. 2wo Wo B A L/2- -L/2

A: In this question we have to draw the shear and moment diagrams for the simply-supported beam.

Q: ah object to remain static, what two conditions must be true? A) Sum of integers = 0 %3D B) All…

A: Let an object be at static state, no linear or angular motion. It will not get any linear motion if…

Q: 2. A uniform beam of length L weighs 400 N and holds a 600 N object as shown in the figure. Find the…

A: Given Weight of beam, W = 400 N Length of beam, L Force on Object , F = 600 N Forces of…

Q: It's exciting watching the construction and renovation happening in Uptown Columbus! On one…

Q: 44. What is the torque about your shoulder axis if you hold a 10.0-kg barbell in one hand straight…

A: 44) Given Mass of barbell is m=10 kg Acceleration due to gravity is g=9.80 m/s2 Distance is r=75…

Q: 1m Suppose we have a non-uniform cantilever beam that is 1 metres long, and has a flexural rigidigy…

A: We have to find the Greens function for the beam.It is easy to use Fourier Transform here

Q: 10.7- A machinist is using a Figure E10.7 vrench to loosen a nut The vrench is 25.0 cm long, and he…

Q: The cable AB carries a tension of 410 N. Determine the moment about O (positive if counterclockwise,…

A: GIVEN: Tension in cable =419N distance between OA =320mm distance between OB = 690mm angle between…

Q: 1-A person holds sphere of weight 60 N in his hand while the forearm is horizontal. The biceps…

A: Part (1): Given: The magnitude of the wight is 60 N. The distance of the biceps muscle from the…

Q: 15) An 82-kg painter stands on a long horizontal board 1.55 m from one end. This 27-kg board is…

Q: The 465-kg uniform I-beam supports the load shown. Determine the reactions at the supports. -5.9 m-…

A: If a system is in equilibrium then 1. Net force on the system = 0 2. Net torque on the system = 0

Q: 5 A force F = 1.3î + 2.7ĵ N is applied at the point x = 3.0 m, y = 0 m. Find the torque about (a)…

A: Given data: Force F=1.3i^+2.7j^ N Point x=3.0m and y=0m

Q: 62. I A 120-cm-wide sign hangs from a 5.0 kg. 200-cm-long pole. A cable of negligible mass supports…

A: The angle between the cable and the sign is,

Q: nates are given in meters: 5.0 kg at (0.0, 0.0) m, 2.9 should a fourth object of 7.0 kg be placed so…

A: m1 = 5 kg at (0, 0) m2 = 2.9 kg at (0,3.7 m) m3 = 4 kg at (2.8 m, 0) m4 = 7 kg Center of gravity =…

Q: What is the lever arm of bicep's tension? 4cm 17.5cm 35cm How much force is supported by the bicep's…

A: The lever arm on the bicep tension is the distance from point of rotation. And the force applied by…

Q: Fig. I shows a uniform ladder t Amitha lead cn it. Ii is leaning.against avreugh wertical availl.…

A: According to the condition of equilibrium, the net or algebraic sum of all forces and moment about a…

Q: A horizontal plank 4.32m long and having mass 25.2 kg rests on two pivots, one at the left end and a…

Q: Three identical coins lie on three corners of a square 10.0 cm on a side, as shown. Determine the x-…

Q: When you carry shopping bags, rather than grasp the handles with your hand as in Q8.14a, you might…

A: For a given set of grocery bags the torque they produce about a person's elbow will be larger the…

Q: In exercise physiology studies, it is sometimes important to determine the location of a person's…

Q: 8. An L-shaped object of uniform density is huung over a nail so that it is free to pivot. What…

Q: Flexor muscle M Elbow joint 0.0510 mt 0.0890 m 0.330 m-

A: Torque on a body is given by the cross product of force acting on it and the distance between the…

Q: 8. A uniform beam, length = 12 m, wt = 800 N, is hinged at the wall and makes an angle of 30° to the…

Q: The uniform 10-kg rod AB is supported by a ball-and-socket joint at A and by the cord CG that is…

Q: 6. A cable supports a uniform boom, which is pivoted at point P. ogble boom P 60.0° If the cable is…

Q: 00 With the shoulder flexed at 30°, the moment arm of the deltoid muscle is 2.0 cm. Solve for the…

A: Given, Weight of humerus = 48N Shoulder is flexed at 30 degree Moment arm of the deltoid muscle is…

Q: The cable AB carries a tension of 480 N. Determine the moment about O (positive if counterclockwise,…

Q: Q5/ If a Moment of M = 300 N. m is applied to the flywheel, determine the force that must be…

A: Given data: M = 300 N.m μs=0.4 Need to determine the force developed in the hydraulic cylinder CD to…

Q: Determine the torque applied to the pipe in the figure given, by a force F = 45 N with an angle…

A: Given data: Force (F) = 45 N Angle (θ) = 60° Distance (r) = d = 50 cm = 0.50 m Required: Torque (τ)

Q: 4. Three forces are acting on a rectangular block of wood as shown, with a pivot in the lower-left…

A: GivenThree forces are acting on a rectangular block

Q: 1. Draw the moment diagram tor girder PQRST and column BGLQ of the building frame. All columns have…

A: Given a diagram and in the question we have ask to draw the moment diagram for girder PQRST and VGLQ

Concept explainers

Center of Gravity of a system

The centre of gravity is a property that is based on the geometry of a rigid body or any particle. It is described as an equilibrium point or a hypothetical location where the total weight of the body is concentrated.

Question

1. Draw a FBD to determine the elbow moment of force necessary to maintain the forearm
in a horizontal position. Solve for the elbow moment with the following: subject mass =
75 kg, forearm length = 32 cm.
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

Torque and the Two Conditions for Equilibrium 17. The arm in Figure P8.17 weighs 41.5 N. The force of gravity acting on the arm acts through point A. Determine the magnitudes of the tension force Ft, in the deltoid muscle and the force Fs exerted by the shoulder on the humerus (upper-arm bone) to hold the arm in the position shown. Figure P8.17
Certain of dinosaurs were bipedal (walked on two legs). What at is a good reason that these creatures invariably had long tails if they had long necks?
(a) Give an example in which the net force acting on an object is zero and yet the net torque is nonzero, (h) (five an example in which the net torque acting on an object is zero and yet the net force is nonzero.
(a) When opening a door, you push on it perpendicularly with a force of 55.0 N at a distance of 0.850m from the hinges. What torque are you exerting relative to the hinges? (b) Does it matter if you push at the same height as the hinges?
Check your Understanding Repeat Example 12.3 using the left end of the meter stick to calculate the torques; that is by placing the pivot at the left end of the meter stick.
a) What is the mechanical advantage of a wheelbarrow, such as the one in Figure 9.24, if the center of gravity of the wheelbarrow and its load has a perpendicular lever arm of 5.50 cm, while the hands have a perpendicular lever arm of 1.02 m? (b) What upward force should you exert to support the wheelbarrow and its load if their combined mass is 55.0 kg? (c) What force does the wheel exert on the ground? Figure 9.24 (a) In the case of the wheelbarrow, the output force or load is between the pivot and the input force. The pivot IS the wheel's axle. Here, the output force is greater than the input force. Thus, a wheelbarrow enables you to lift much heavier loads than you could with your body alone. (b) In the case of the shovel, the input force is between the pivot and the load, but the input lever arm is shorter than the output lever arm. The pivot is at the handle held by the right hand. Here, the output force (supporting the shovel's load) is less than the input force (from the hand nearest the load), because the Input is exerted closer to the pivot than is the output
The forearm shown below is positioned at an angle with respect to the upper arm , and a 5.0- kg mass is held in the hand. The total mass of the forearm and hand is 3.0 kg, and their center of mass is 15.0 cm from the elbow. (a) What is the magnitude of the force that the biceps muscle exerts on the forearm for =60 ? (b) What is the magnitude of the force on the elbow joint for the same angle? (c) How do these forces depend on the angle ?
A cook holds a 2.00-kg carton of milk at arm's length P8.19). What force FB must be exerted by the biceps muscle? (Ignore the weight of the forearm.) Figure P8.19
(a) What minimum coefficient of friction is needed between the legs and the ground to keep the sign in Figure 9.35 in the position shown if the chain breaks? (b) What force is exerted by each side on the hinge?
(a) Is it possible to calculate the torque acting on a rigid object without specifying an origin? (b) Is the torque independent of the location of the origin?
Two children of mass 20.0 kg and 30.0 kg sit balanced on a seesaw with the pivot point located at the center of the seesaw. If the children are separated by a distance of 3.00 m, at what distance from the pivot point is the small child sitting in order to maintain the balance?
A museum of modern art is displaying an irregular 426-N sculpture by hanging it from two thin vertical wires, A and B, that are 1.25 m apart. The center of gravity of this piece of art is 48.0 cm from its extreme right tip. Find the tension in each wire.