Solve the ff and show complete solution 10.7 · A machinist is using awrench to loxsen a nul. TheFigure E10.7wrench is 25.0 cm long, and he17.0 Nexcrts a 17.0-N force alt the end of37the handle al 37° with the handle(Fig. E10.7). (a) What torquedoes the machinist exert aboutthe center of the nut? (b) What-25.0 cm-Nutis the maximum torque he couldexert with this force, and how should the force be oriented?

Answered: Image /qna-images/answer/947d5d4d-14b7-4a52-9bd3-d3e8d85cb2e7.jpg

10.7- A machinist is using a Figure E10.7 vrench to loosen a nut The vrench is 25.0 cm long, and he 17.0N xerts a 17.0-N force at the end of 37 he handle at 37° with the handle Fig. E10.7). (a) What torque loes the machinist exert about -25.0 cm- he center of the nut? (b) What s the maximum lorque he could xert with this force, and how should the force be oriented? Nut

10.7- A machinist is using a Figure E10.7 vrench to loosen a nut The vrench is 25.0 cm long, and he 17.0N xerts a 17.0-N force at the end of 37 he handle at 37° with the handle Fig. E10.7). (a) What torque loes the machinist exert about -25.0 cm- he center of the nut? (b) What s the maximum lorque he could xert with this force, and how should the force be oriented? Nut

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 25P: When opening do you push on it perpendicularly with a force of 55.0 N at a distance of 0.850 m from...

See similar textbooks

Similar questions

Check your Understanding Repeat Example 12.3 using the left end of the meter stick to calculate the torques; that is by placing the pivot at the left end of the meter stick.
Find the net torque on the wheel in Figure P10.23 about the axle through O, taking a = 10.0 cm and b = 25.0 cm. Figure P10.23
When opening do you push on it perpendicularly with a force of 55.0 N at a distance of 0.850 m from the hinges. What torque are you exerting relative to the hinges?
A strut of lengthL = 3.00 m and mass m =16.0 kg is held by a cableat an angle of θ = 30.0°with respect to the horizontalas shown in FigureP8.30. (a) Sketch a forcediagram, indicating allthe forces and their placementon the strut. (b) Why is the hinge a good place to usefor calculating torques? (c) Write the condition for rotationalequilibrium symbolically, calculating the torques around thehinge. (d) Use the torque equation to calculate the tension in the cable. (e) Write the x- and y-components of Newton’ssecond law for equilibrium. (f) Use the force equation tofind the x- and y -components of the force on the hinge.(g) Assuming the strut position is to remain the same, wouldit be advantageous to attach the cable higher up on the wall?Explain the benefit in terms of the force on the hinge andcable tension.
A dental bracket exerts a horizontalforce of 80.0 N on a toothat point B in Figure P8.6. What isthe torque on the root of the toothabout point A?
10kg rigid beam that is 3mlong is supported at each end. An8kg block is placed 2m fromsupport 1. How much upward forcedoes each support provide to ensurezero acceleration and zero torque?Note, if an object is not rotating, itis not rotating about every axis.
Zane and Phoebe are sitting on opposite ends of a teeter‑totter that is 4.00 m4.00 m long with the pivot point in the exact center. Zane weighs 433 N433 N and Phoebe weighs 341 N.341 N. What torque does Zane's weight exert?
•• A squirrel-proof bird feeder has a lever that closes to protect theseeds when a 0.42-kg squirrel sits on it, but not when a 0.077-kgbird perches there. (a) If the lever radius is 9.6 cm, what torquesdo the squirrel and the bird each exert on it? (b) The torque produced by the animal is balanced by a spring that applies a perpendicular force a distance of 3.5 cm from the axis of rotation. Ifthe squirrel must stretch the spring 2.5 cm in order to close thelever and protect the seeds, what should be the force constant ofthe spring
Find the net torque on the wheel in Figure P8.4 about theaxle through O perpendicular to the page, taking a =10.0 cmand b= 25.0 cm.
A force F⃗ =7i^+2.7k^ N is applied at the point (3,0,1) m. What is the y component of the torque?
The body in the figure is pivoted at O. Three forces act on it in the directions shown: FA = 8.10 N at point A, 5.60 m from O; FB = 16.0 N at point B, 3.90 m from O; and FC = 18.0 N at point C, 3.50 m from O. Taking the clockwise direction to be negative, what is the net torque about O?
Wouldn't the torque equal Fx +Fy?