1. If a DC voltage is applied to a DC motor, then, according to Fleming's Left hand Rule, the motorthat develops a torque which causes the rotation.Q/Choose thewill experiencea. Back EMF (Eb)right optionsb. Mechanical forcec. Energyd. None of the above2. The lost torque resulting from the difference (Ta - Tsh) represents_a. iron lossc. friction lossb. electrical lossd. both a and c

1) working principle of DC motor 2) Lost torque in the motor represents

1. If a DC voltage is applied to a DC motor, then, according to Fleming's Left hand Rule, the motor that develops a torque which causes the rotation. will experience a. Back EMF (Eb) Q/Choose the right options b. Mechanical force c. Energy d. None of the above 2. The lost torque resulting from the difference (Ta - Tsh) represents_ a. iron loss c. friction loss b. electrical loss d. both a and c

1. If a DC voltage is applied to a DC motor, then, according to Fleming's Left hand Rule, the motor that develops a torque which causes the rotation. will experience a. Back EMF (Eb) Q/Choose the right options b. Mechanical force c. Energy d. None of the above 2. The lost torque resulting from the difference (Ta - Tsh) represents_ a. iron loss c. friction loss b. electrical loss d. both a and c

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a 220V shunt generator has an armature resistance of 0.02ohms and a shunt field resistance of 44 ohms. at rate load, the driving engine develops 62.26 hp. If the iron and friction losses amount to 1600W, how much is the current delivered to the load at this condition? (Our subject is ELECTRICAL MACHINE 1, and our lesson is Losses an Efficiency in DC Machine) (I need clean solution ma'am/sir, thank you so much)
A 220V shunt generator has an armature resistance of 0.02ohms and a shunt field resistance of 44ohms. at rate load, the driving engine develops 62.26hp. If the iron and friction losses amount to 1600W, how much is the current delivered to the load at this condition? (Our subject is ELECTRICAL MACHINE 1, and our lesson is Losses and Efficiency on the DC MACHINE) (I need a clean solution ma'am/sir. Thank you do much)
A 220 V dc machine has an armature resistance of 1ohm if the full load current is 20 A, the difference of induced voltage, when the machine is running as a motor and generator, is *
A d.c. shunt machine has armature and field resistances of 0.025 Ω and 80 Ω respectively. When connected to constant 400-V bus-bars and driven as a generator at 450 r.p.m., it delivers 120 kW. Calculate its speed when running as a motor and absorbing 120 kW from the same bus-bars
what is the best suitable motor for below application? In a belt conveyor system used to transport bulk solids, the belt speed is required to be maintained constant at the set speed all the time irrespective of the bulk solids content on the belt. Hence, the electric motor used in this system should be able to operate more or less at a constant speed in a wide range of different torque values.
EE 422 - AC and DC Machinery Solve the following problems completely. Box and Round-off your final answer in nearesttwo decimal places 1.A 25 hp,250V long shunt compound motor takes 5 A when running light and runs at 1150 rpm. Armature resistance, 0.15 ohm, Shunt field resistance, 200 ohm and series field resistance, 0.05 ohm. At rated load the motor takes 86.5A and runs at 720 rpm. Determine the ratio of torque developed from no-load to full load. answer: 1:34 2.A compound motor develops a torque of 271 lb-ft when it is operating at 1200 rpm, under which condition its armature current Ia is 215 amperes. What will be the developed horsepower of the motor if the load is increased so that it slows down to 1,1120 rpm in which case Ia changes to 238 amperes and the total flux increases by 8 percent? answer: 69.1hp
Derive the following in terms of the physical parameters of the induction machine: a- the slip at maximum torqueb- the maximum torque
A d.c series machine rated at 200V, 100A has an armature resistance of 0.1Ω and field resistance of 0.15 Ω . The friction and windage loss is 1500W . Use a Vbase of 200V and an Ibase of 100A . Use the above information to answer the questions below. a.Calculate the per unit value of the total series resistance of the machine. b. Calculate the per unit value of the friction and windage loss. c. Calculate the per unit value of the total series resistance loss at the rated load. d. Calculate the per unit value of the total power loss at the rated load. e. Calculate the per unit value of the efficiency of the machine .
A 500 V, lap wound d.c. A shunt motor has 90 slots and each has 8 conductors. When the motor delivers full load it draws a current of 30/ A from the line. The field and armature resistances are 250 ohm and 0.4 ohm respectively. If the fixed resistance is 27.1 mWh, find the speed of the motor and the torque produced.
A 25kW, 250V DC shunt generator has armature and field resistances of 0.06 ohm and 100 ohm respectively. Determine the total armature power developed when working (i) as a generator delivering 25kW output and (ii) as a motor taking 25kW.
Find the rated torque.
A 220V shunt generator has armature resistance of 0.2 ohms and a shunt resistance of 44 ohms. At rated load, the driving engine develops 62.5HP. if the iron and friction losses amount 1600W, how much is the current delivered to the load at rated condition?