1. Samples 0 to 7 of a signal have the value: x(n) = {1, 3, 2, 4, -5, -6}. (The bold sample denote origin/0th sample) Calculate the following - a. Impulse Decomposition b. Step Decomposition c. Even/Odd Decomposition (For even/odd decomposition, assume that the system looks at signal as cyclic and periodic, also notice that the number of samples is even)

1. Samples 0 to 7 of a signal have the value: x(n) = {1, 3, 2, 4, -5, -6}. (The bold sample denote origin/0th sample) Calculate the following - a. Impulse Decomposition b. Step Decomposition c. Even/Odd Decomposition (For even/odd decomposition, assume that the system looks at signal as cyclic and periodic, also notice that the number of samples is even)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An analog signal contains useful frequency component upto 100 hz what is nyquist rate for this signal? suppose we sample this signal at 250 samples/sec what is highest frequency component that can be reprensented uniquely at this sampling rate
During a vibration measurement experiment in the Mechanical Engineering Department at Hacettepe University, a piezoelectric accelerometer output is given by this mathemtaical equation: a (t) = 1 + 4 sin(43.98t) + 7sin(100.53t) in gravity acceleration (g) value. a) Determine the frequencies (in Hz) contained in the signal. Round your results to nearest integer value. b) What is the minimum sampling rate to avoid aliasing? c) Sketch clearly the frequency spectrum if the signal is sampled at 15 Hz. d) Now, the signal is filtered with a low-pass Butterworth filter to remove the maximum frequency component. It is desired to attenuate the amplitude of this component to at least 5 % of its value. If the sampling rate is now 20 Hz, what will be the order of the filter? e) If the blue one is our signal, then what is red and green ones? Write down the mathematical relation between the three signals? (Use labels as blue, red and green signal.)
Ex. 1780. A closed-loop system has sustained oscillations (i.e. constant amplitude) with a period of 85 seconds when the gains are: proportional=96, integral=0, and derivative=0. Determine the ideal- PID gains Kp, Ki (minutes^-1), Kd (minutes) using the Ziegler-Nichols method. Also determine the standard-PID values which are commonly used in industry, such as LabVIEW: Kc, Ti (min), Td (min). ans:6
Kindly help to answer this figure shown. Find the transfer function of the system whose signal flow graph is shown
1. What is the order of the RC filter transfer function? 3rd 2nd 4th 1st 2. Why are unity gain amplifiers used? To separate complicated chains in signal transmission into separate simple circuits To filter the signal To amplify the signal To “condition the signal” so there is no voltage dividers
1. Kindly determine its transfer function, C/R, using Block Diagram Reduction and Block Diagram Algebra.2. Kindly convert it into an equivalent Signal Flow Graph and compute its error ratio, E/R, using Mason’s GainFormula.
6.1 A 1 kHz sine wave is sampled at frequency of 5 kHz.(a) What is the Nyquist frequency of the sampling system in this case? Showyour work.(b) What is the Nyquist rate of the signal? Show your work.(c) Is the signal properly sampled; that is, will there be aliases in the digitallyrecorded signal? Explain.(d) What if the original analog signal included both even and odd harmonics of itsprimary frequency; that is, 2, 3, 5 kHz, etc. What would be the highest harmonicthat will be faithfully represented in the discrete-time version of the analogsignal?(e) Following on with the previous step, what is the lowest harmonic that will bealiased and what would be resulting alias frequency?
An analog signal, with an absolute bandwidth of 10 KHz, is to be converted to a digital signal usingan A/D converter and stored in a PC. If the quantization error must be within ±0.05% of the peak-to-peakvalue of the analog signal, determine the storage requirement. Please assume that we are going to record 8seconds of data, sampled at 1.5 times the Nyquist rate.
Explain the Sampling Theorem and Nyquist Theorem. Give an example
The front end of a television receiver, having a bandwidth of 7MHz and operating at a temperature of 27°C, consists of anamplifier having a gain of 15 followed by a mixer whose gain is 20.The amplifier has a 300-Ω, input resistor and a shot-noiseequivalent resistance of 500-Ω; for the converter, these values are2.2 and 13.5 kΩ, respectively, and the mixer load resistance is 470kΩ. Calculate Req for this television receiver.
1. During the process of digital sampling, data can be lost due to aliasing.Analyse this problem and provide at least two possible solutions. Also,determine the rate at which a signal should be sampled, if the highestfrequency is 50MHz. (b) An 9-bit binary number is used to represent an analog value in the rangefrom -10oC to 100oC, determine the resolution of the system andinterprete your result.
For the system defined by the first-order differential equation: Draw the log magnitude (dB)-log frequency graph of H(jw). (The phase graph is not required. The frequency axis is expected to be logarithmic when drawing the log magnitude graph.) The input is assumed to be suppressed when the magnitude of H(jw) is -40dB. It is given that the x(t)=coswat signal is suppressed by this system. What is the smallest value of wa in this case?