1. The input of a voltage follower has a square waveform. Draw the output waveforms (v.) of a voltage follower for the following 4 input waveforms (vV»). The slew rate of the op-amp is 0.25 - (a) (b) 5 V Vin 5 V Vin 0V- OV 5 5 us us 10 μs 10 μs (c) (d) Vin Vin 10 V 10 V OV- 5 5 us us 10 µs 10 µs

1. The input of a voltage follower has a square waveform. Draw the output waveforms (v.) of a voltage follower for the following 4 input waveforms (vV»). The slew rate of the op-amp is 0.25 - (a) (b) 5 V Vin 5 V Vin 0V- OV 5 5 us us 10 μs 10 μs (c) (d) Vin Vin 10 V 10 V OV- 5 5 us us 10 µs 10 µs

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 13PP: In an R-L parallel circuit, IT=1.25 amps, R=1.2k, and XL=1k. Find IR

See similar textbooks

Similar questions

An ideal op-amp circuit is shown above, with dc supply Vcc = -Vcc = 20V on both op-amps.Assume that v1 = 4V, v2 = 2V, R1 = R4 = 9kΩ, R2 = R5 = 4kΩ, R3 = 5kΩ. Please determine the output voltage vo in volts.
Find the maximum possible output voltage deliverable by an op-amp if it’s slew rate is 1volt/μs and frequency of input signal is 06.5 Khz.
Create Op-amp circuit... with:Vin= -1 Volt (DC) Vout = 14 Volt (DC) Only resistors with 1k, 3k, 5k, 7k and 11k ohms can be used while the circuit is being built. The V+ value of the LM741 IC to be used for op-amps will be 20 volts and the V- value will be -20 volts. You need to use at least one inverting amplifier and one non-inverting amplifier to build the circuit. Question: Write the gain formula of the circuit and calculate it, and write how we should find the Vout value..
From the figure , write note voltage equations, one for each input terminal of the op amp The expression for the load current ( iL) can be written as a function of the input voltage (Vin) and the load voltage (VL) IL =A(Vin) + B(VL) b.1 What is the expression for A? b.2 What should be the condition for R1 R2 R3 R4 so that B is zero? (NB this will make( iL) depend only on Vin and not on RL)
. For the combinational op-amp circuit A. Identify the connection/application of each op-amp: A1, A2, A3 and A4. B. Find V01, V02, V03, and V0.
For the given op-amp circuit, determine: (a) iout/iin2, (b) iin2/iin, (c) iin/Is, and (d) iout/Is.
Calculate ix and v0 in the circuit attached. Assume that the output of the Op-Amp is constrained to lie between -15V and 15V.
List any four properties of a practical op amp. 2.In an opamp inverting amplifier circuit, Rf = 10 kΩ. and Ri = 1.6 kΩ. Find the output voltage when the input voltage is (a) +0.35 V (b) -2.2V 3.In an opamp non-inverting amplifier circuit, Rf = 10 kΩ. and Ri = 4.7 kΩ. Find the output voltage for an input voltage of (a) -5.6 V (b) + 0. 7 V
I have attached the image of the OpAmp. Question is, Derive the reationship between the output (V0) and input voltages (V1 and V2) for the following op-amp circuit.
Correct answer will be upvoted else downvoted. Need the answer quickly. Give the characteristics of ideal op-amp. Provide a brief answer.
Find the output voltage vO in the following figure if the op-amp is ideal and VZ = 12 V. Find the values of the emitter current and the total current supplied by the 15-V source. Assume βF = 62. Find the op-amp output voltage. Given that R1 = 53 kΩ and R2 = 104 kΩ.
Does output voltage for a inverted op amp Voup= +Vsat