1.Name type of failures in engine blocks

Q: Find the exhaust pressure for the compressor

A: Given     Intake Properties           Pressure, P1 = 12 psia           Temperature, T1 = 2oC Exhaust…

Q: The API rating of a fuel oil is 320. What is its specific gravity at 280C? Put your answer in 3…

A: Given API fuel is 32o To find Specific gravity at 28o

Q: List five different types of oil rating systems

A: Oil Rating Systems:- The society of Automotive Engineers SAE has established a numerical code…

Q: Write the monthly maintenance schedule or chart for compressor propeller

A:

Q: please draw technical drawings of the pipeline of lubrication oil system in an ship engine room.

A:

Q: 1) For vapour contained in an engine 2 cylinder:

A: we have to discuss about the vapor contained in the system

Q: A perfect gas nas and pressure 0.8 bar and volume

A: Change in entropy: Entropy is the ratio of heat transfer (Q) to temperature (T). According to second…

Q: The shaking forces acting on an engine is mainly due to

A: The shaking forces acting on an engine is mainly due to  Answer: Crank

Q: iscuss what is the effect of efficiency on compressor temperature and duty.

A: A compressor is a device that reduces the volume of a material (typically a gas) to raise its…

Q: C2 (ii) Explain the operating characteristics of wind mill.

A: NOTE : As per guideline ,we can only do 1 question at a time. so please upload the remaining…

Q: Explain with neat sketch of crank and lever mechanism used in oil and gas industry.

A: Crank and slotted lever mechanism:-

Q: HOW TO PERFORM LEAK TEST ON HVAC DUCTS? Badly needed asap. Brief and clear Explanation. I will rate…

A: The leak test on HVAC ducts is performed in few steps. These steps are given as under,

Q: ration i

A: given: Methods for treating vibration in pumps

Q: What happens if value of compression ratio is high?

A: A good advantage of the higher compression ratio is, that the higher compression ratio increase the…

Q: Types of engine oil

A: There are mainly three types of engine oil  1. Full Synthetic engine oil 2. Mineral engine oil  3.…

Q: Briefly explain the difference between a compressor and internal combustion engine.

A: Difference between a compressor and internal combustion engine.

Q: Explain air measurement and control methods of ECU in diesel engines

A: Most fuel injection systems use electronics to control the opening and closing of the nozzle.…

Q: Do not operate the cargo door with a cross wind component of more than: (a) 55 kt (b) 45 kt (c) 35…

A: There are some limits on the opening of the cargo and passengers doors for the safety reason. If the…

Q: The factor of safety for the piston rod is

A: Given data; diameter (d) =20mmlength (l)=700 mmforce=10 kNYOUNG MODULUS=200 GPa acc. to question we…

Q: Explain the difference between the inherent and installed valve characteristics.

A:

Q: Write a note and explain about Modification of turbojet engine

A: TURBOJET ENGINE  A turbojet engine has all the power by expelling a high-energy gas stream from the…

Q: temperature is necessary fc

A: Temperature= 56.85 deg c.

Q: What happens if value of compression ratio is low?

A: The compression ratio is defined as the ratio of initial volume at the entry of compressor by the…

Q: cylinder is 0.0356". The said oute al places and in Ibf-s/ft?.

A:

Q: Design a piston for use in automobile engines (piston ring, pin, skirt).

A:

Q: The API rating of a fuel oil is 30°. What is its specific gravity at 21°C? Put your answer in 3…

A: Given          API rating = 30 Temperature, T = 21oC Find  Specific gravity, SG

Q: Engineering Utilities Please answer in paragraph form. UPVOTE will be given. Discuss/Explain the…

A:

Q: neumatic Dia

A: Required  Pneumatic diagram and name of its component.

Q: Assume that after removing the cylinder head of an engine, a wet, oily condition is noticed on the…

A:

Q: tail force

A: Tail force is 15kN

Q: Choose the correct option  Engine pistons are usually made of aluminium alloy because it  A.Is…

A: Piston -cylinder assembly piston is a very crucial part of the assembly. Because during the…

Q: Technician A says that excessive engine oil consumption can be caused by low oil levels. Technician…

A: Answer:- Technician B correct.

Q: Describe an acceptable storage area for a cylinder offuel gas.

A: Storage cylinders are used for the storage of the fuel gases. These cylinders are made up of iron or…

Q: iency of a dies of fuel is 418

A:

Q: What is a standpipe?

A:

Q: The 4 basic classifications of engine gaskets are?

A: Determine the 4 types of engine gasket as given below. (a) Cylinder head gasket - Copper and…

Q: State four (4) behavioral characteristics of black oils if pressure of reservoir is above the bubble…

A: Bubble point pressure is the pressure at which the first bubble of gas evolves from an unsaturated…

Q: Which temperature for lubricating oil will be lowest? 1) Flash point 3) Pour point 2) Fire point 4)…

A: Pour point A point for a liquid at which its flowing property changes and becomes semisolid in…

Q: 15) What is Automobile ty tubeless tyre

A: In other word we can say that tire is a ring-shaped component that surrounds a wheel's rim to…

Q: The engine speed

A: Given; Each of front two springs stiffness, k1=16 MN/mWhile the stiffness of each rear spring,k2 =…

Q: Standard operating procedures for internal combustion engine(mounted on vehicle)

A: An IC Engine is basically of two types. Petrol / Gasoline Engine Diesel Engine A petrol engine…

Q: endurance limit wil

A:

Q: Diesel engine fuel is rated by?

A: It is required to rate the diesel fuel

Q: Give examples fof impact.

A: The definition of impact is one thing crashing into or having an effect on another.

Q: List out the design requirements of diesel engine combustion chamber

A: Diesel engines work on the diesel cycle. In diesel engines, the air is compressed alone and at the…

Q: of motion for the syste

A:

Q: List out the applications of compressed air used in oil and gas industries

A: To find:  applications of compressed air used in oil and gas industries

Q: eed correct solution of all p

A: vB=2.2m/saB=30 m/s

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.