10. Water at 25 °C is transferred 10 m high to the first floor using stainless steel pipes (e = 2 x 106 m) with a diameter of 2 cm. If the water leaves through a faucet of diameter 1.3 cm at a flow rate of 8 x 10+ m³/s. Determine the required pressure at point 1 (P:) if: a) All viscous effects are ignored b) Only major losses are considered c) All loses are considered (major + minor) Assume that the density and viscosity of water at 25 °C is 997 kg/m and 0.891 x 10-3 kg/m.s, respectively. You can use relevant tables and Moody chart to find the required properties. L=4m L=4 m K, = 2.5 10 m K15 L=4m K=0.5 K=8 Water L-5m L-4m L-4m

10. Water at 25 °C is transferred 10 m high to the first floor using stainless steel pipes (e = 2 x 106 m) with a diameter of 2 cm. If the water leaves through a faucet of diameter 1.3 cm at a flow rate of 8 x 10+ m³/s. Determine the required pressure at point 1 (P:) if: a) All viscous effects are ignored b) Only major losses are considered c) All loses are considered (major + minor) Assume that the density and viscosity of water at 25 °C is 997 kg/m and 0.891 x 10-3 kg/m.s, respectively. You can use relevant tables and Moody chart to find the required properties. L=4m L=4 m K, = 2.5 10 m K15 L=4m K=0.5 K=8 Water L-5m L-4m L-4m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe experienced a total head loss of 15 m, determine thepressure difference from its starting point to discharge point inkPa.
A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a pressure of 150 kPa. The throat diameter of the me- ter is 100 mm and the pressure at the throat is 400 mm of mercury below atmosphere. If 3% of the differential pressure is lost between inlet and the throat, determine the flow rate of the pipeline. PLEASE USE BERNOULLI'S ENERGY EQUATION. INCLUDE COMPLETE SOLUTION
Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc
Apply Bernoulli equation in solving the problem: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127 cm manometer filled with mercury is used to measure the pressure difference across the venturi meter. If the manometer reads 101.6 cm when 15 °C water is flowing through the pipe, what is the flow rate of water (m3/min)? Assume that the venturi meter coefficient of discharge equals 0.98.
Q1: In a venturemeter used for measuring the flow ofoil (-0.85) through a horizontal pipeline, the pipe diameter is 2.4 times the diameter at the throat. Connections are made from the entrance to the meter and the throat to a vertical L tube containing mercury If the difference level between the fluids in the U - tube arms is (x +) in em, where S.N. is student serial number. Neglect friction in the pipe. Find an expression in terms of x for the velocity of the oil in the pipe.
1 - If the pipeline is now specified to be of Schedule 40 with a nominal diameter of 6 in., and the available pressure at the pump exit is P2 = 132.7 psig, what flow rate Q (gpm) can be expected? Answer the following additional questions: 2 -If the combination of pump and motor is 80% efficient, how much electrical power (kW) is needed to drive the pump? 3 -, in order to avoid vapour lock, the pressure in the pipeline must always be above the vapor pressure of the crude oil, what is the maximum permissible elevation of point 3 relative to point 4? 4 -If the flow in the pipeline were at the upper limit of being laminar, what pump exit pressure would then be needed? (Answer this part without using the friction factor plot.
HW Question : The tank-pipe system is to deliver at least 12.5 m3/h of water at 20°C to the reservoir. What is the maximum roughness height ε allowable for the pipe? Neglect minor losses.
What is the entrance length in a 4-cm-diameter pipe if 0.5*10^ -4 m^ 3 / s water is flowing
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (e = 0.00061 m).Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flowthrough the pipe, what must be the pressure at A? Ans. 314 kPa (show the complete solution with diagram) [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet.E.g. (density, viscosity). Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness]
The tank–pipe system of Fig. is to deliver at least11 m3/h of water at 20°C to the reservoir. What is themaximum roughness height ε allowable for the pipe?