Answered: 10. With a step-up transformer with a…

10. With a step-up transformer with a turns ratio of 6 and a primary voltage of 100V, what is the voltage on the secondary? O 6 V 60 V 6000 V 600 V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter27: Single-phase Transformers

Section: Chapter Questions

Problem 4RQ: All values of a transformer are proportional to its __________________ ___________________.

See similar textbooks

Related questions

Q: For the network function T(s) = - , the resonant frequency and s² +25 +100 bandwidth are…

A: The natural frequency and damping ratio cam be computed by comparing the given transfer function…

Q: In simple explanation, why transistor is called CURRENT CONTROLLED DEVICE? I really need to…

A: Transistor : A transistor acts as a switch which main function function is to regulate the voltage…

Q: Consider a straight conductor of length 7.7 cm. The conductor moves at right angles to a magnetic…

A: We need to find velocity

Q: Calculate for Voltage across each Resistors VAB, VBG, VCB, VCG, VCD, VED, VFE, VFG (consider the…

A: given here a circuit and asked to find the voltages across each resistor.

Q: 1. Determine the equivalent impedance and the equivalent admittance.

Q: nd the amplitude V the angular velocity w and the phase shift å for the sinusoidal Itage v(t) V…

Q: 3. Given an AM signal PAM (t) = [1.5 + m(t)]cos(1000nt) where m(t) = 1.5[u(t) – u(t – 2)]- 1.5[u(t –…

A: Given an AM signal ϕAM(t)=[1.5+m(t)]cos(1000πt) where , m(t)=1.5[u(t)-u(t-2)]-1.5[u(t-2)-u(t-3)]. a)…

Q: Convert the quantities (176 - j132) and by the phasor (12 + j16) to polar form, divide the first…

Q: Compare between squirrel cage rotor and solid iron rotor

A: Types of Rotor Squirrel cage Rotor ( In this Rotor, conductor twisted by some specificied angle…

Q: (c) Find the currents /, and 2 in the circuit of figure 4 52 25V 40V 65V Figure 4

Q: (d) Bilinear Transformations and Equivalence One approach to realising a digital filter is to…

A: Butterworth filter is a filter used for filtering low frequencies, in the passband as it is Q factor…

Q: Can transistor can be used as a switch? ° What happens when the switch is off in a transistor? ° Why…

A: Reason BJT is a current controlled Device in which base current control the mode of operation of…

Q: Suppose the audio signal has a bandwidth of 6 kHz. If the maximum quantization error needs to be no…

A: We need to find out the number of quantization level and number of bits per level .

Q: 2.49. Consider the four-resistor bias network of Figure 12.22(a) on page 620, with =D200 kQ, R2=100…

Q: If the Q-factor of a coil at resonant frequency of 1.5 MHz is 150 for a series resonant circuit,…

A: Given: Quality factor, Q = 150 Resonant frequency, fr=1.5 MHz

Q: sine wave resulting in an FM signal having a maximum frequency of 107.218 MHz and a minimum…

Q: Compare between solid iron rotor and drag-cup rotor

Q: find the sinusoid represented by the polar.

A: In this question, We need to find the sinusoid represented by the polar

Q: Construct a complex circuit that will produce total resistance of 342.222 -hET. Draw your diagram.…

Q: Given the information appearing in the multiple-feedback BPF, calculate fo

A: The cutoff frequency can be calculated by using the general expression of multiple feedback band…

Q: Consider a cellular tower with Pt=10W, Gt=10 dBi, Gr=3 dBi, and L=0 dB, a. At 4000 MHz compute the…

A: Given Consider a cellular tower with Pt=10W, Gt=10 dBi, Gr=3 dBi, and L=0 dB, a. At 4000 MHz…

Q: Draw and label completely and properly the block diagram of MOD7 synchronous down counter with the…

A: Flip-flop: This is a resister to store the 1-bit data. This is the basic building block of the…

Q: The system function of a causal LTI system is 1+z¬! H(2) = (1 – 0.5z-1)(1+ 0.25z-1)' a) What is the…

A: The system function of a causal LTI system is: H(z)=1+z-1(1-0.5z-1)(1+0.25z-1) a) We need to find…

Q: 202 55N + I2 100V I3 250V + Figure 1

Q: R Vin (t) Vout (t) Figure 7

Q: When two or more out of phase pulses interfere, they ____________. I. destroy each other II.…

A: Pulse is nothing but a disturbance or a deviation in voltage or current, interference is nothing…

Q: Evaluate. No solution, final answer only in rectangular form. ... 10230° + (2 – j4) y = 100| (3 +…

Q: z, four-pole, induction motor connected in star

A: Three Phase Induction machine-This Induction machine comprises of rotor and stator as it basic parts…

Q: Given that Vin = VpeakSinwt volts, Vpeak= 5V, R1 = 1kN, and using the ideal forward voltage of 0.7V,…

Q: Given: Vin = Vpeak sin(w)(t) Vpeak = 5V R1 = 1k ohms Using ideal forward voltage of…

Q: 10245°= A 7.07+7.07j 10+10j C 10+14.14j 10+45j

Q: 5. For the circuit shown below: Rf +15 Ri Vout -15 a.) If Re=2 MQ and R; = 50 2, what is the voltage…

Q: For the given circuit determine the voltage gain byletting the emitter capacitor with negligible…

A: We need to find out Gain for given circuit

Q: A 230V DC series motor operates at its full load current and speed of 22A and 750 revolutions per…

A: Types of DC Motor Seperetely excited motor Series Motor Shunt Motor Compound Motor Differential…

Q: Why did the synchronous motor stop as soon as we set the speed of the prime mover to 2500 rpm then…

A: As we know that in synchronous motor we have to give suppy from stator to produce three phase…

Q: What is the free space loss in dB between two antennas 38 km apart operating at 7.0 GHz? (Use 2…

Q: Compare between squirrel cage rotor and drag cup-rotor

Q: For the network of Fig. 170, sketch v, and determine Vae- 2k V; = 120 V (rms) Ideal % (Vác) FIG. 170…

A: Considering input wave to be sinusoidal the output is drawn. Plotted output waveform using transfer…

Q: An automatic pressure control system measured the output as 8 psi. If error signal is 5 psi, such…

Q: 27. Leg ?

A: We are authorized to answer one question at a time, since you have not mentioned which question you…

Q: Given: Vin = Vpeak sin(w)(t) Vpeak = 5V R1 = 1k ohms Using ideal forward voltage of 0.7V What is…

A: In this question we need to draw the output and input voltage waveform and Calculate for the average…

Q: 7) The restricted earth protection for the transformer is on the (A) high voltage side. (B) low…

Q: QI A 380 V, 50 Hz, 3-phase, star-connected induction motor has the following equivalent circuit…

Q: For an RLC series circuit, the voltage amplitude and frequency of the source are 140 V and 500 Hz,…

Q: 3. Find the resonant frequency for the two branch parallel circuit, branch 1 consist of R = 10 Ohms…

Q: Given, r(t) = 3t^2, therefore its laplace transform is O a 6/s^3 O b. 6/ s^2 Oc 3/ s^2 O d. 8/ s^3

Q: Explain the RC time constant and what its value means in terms of circuit characteristics.

Q: Determine the inductor current i(t) shown in the circuit below. t = 0 4Ω i(1) 16 0 20 V 0.4 H v(1)…

A: Current: It is the time rate of the change of the charges. The direction of the current is opposite…

Q: Sketch v, for each network of Fig. 181 for the input

Q: Q4. (a) () Discuss the operating principle of an induction generator. (i) Discuss TWO advantages and…

A: INDUCTION GENERATOR: An induction generator, also known as an asynchronous generator, is an…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

10. With a step-up transformer with a turns ratio of
6 and a primary voltage of 100V, what is the
voltage on the secondary?
6 V
60 V
6000 V
600 V

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

All values of a transformer are proportional to its __________________ ___________________.
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
For an ideal 2-winding transformer, an impedance Z2 connected across winding 2 (secondary) is referred to winding 1 (primary) by multiplying Z2 by (a) The turns ratio (N1/N2) (b) The square of the turns ratio (N1/N2)2 (c) The cubed turns ratio (N1/N2)3
A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
What is the purpose of the transformer in Figure 6.25?
(a) An ideal single-phase two-winding transformer with turns ratio at=N1/N2 is connected with a series impedance Z2 across winding 2. If one wants to replace Z2, with a series impedance Z1 across winding 1 and keep the terminal behavior of the two circuits to be identical, find Z1 in terms of Z2. (b) Would the above result be true if instead of a series impedance there is a shunt impedance? (c) Can one refer a ladder network on the secondary (2) side to the primary (1) side simply by multiplying every impedance byat2 ?
Two transformers rated at 100 kVA each are connected in an open-delta connection. What is the total output power that can be supplied by this bank?
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
You are an electrician working in an industrial plant. A 30-hp three-phase induction motor has a current draw of 36 amperes at full load. The motor is connected to a 480-volt line. A three-phase wattmeter indicates a true power of 22 kW. Determine the power factor of the motor and the amount of capacitance needed to correct the power factor to 95. Also determine the minimum voltage rating of the capacitors. The capacitors are to be connected in wye.
If a capacitor produces 15 ampere on a 240-volt supply, which of the following is its microfarad rating? 166 microfarad 15 microfarad 200 microfarad 3450 microfarad
A 100 percent efficient iron-cored transformer has a primary winding with 1820 turns and secondary winding with 125 turns. If he ac voltage across the primary winding is 110V what will be the AC voltage across the secondary? Please solve the problem
A 3-phase 1000KVA, 11000/416 transformer is delta-connected on the primary and star connected on the secondary. The primary resistance / phase is 1.45 Ω and secondary resistance/phase is 0.0006 Ω. determine the efficiency on full-load at 0.85 power factor lagging if the iron loss is 1770 W. *