i need the answer quickly 06: Water (p = 1000 kg/m) flows from a largetank through a large pipe that splits into two imallerpipes as shown in Fig. If viscous effects are negligible,determine the flow rate from the tank and thepressure at point (1).0.03-m diameter0.05-m diameter(1)0.02-m dianeter

Answered: Image /qna-images/answer/09ad9dd4-5698-4104-af0c-8a400f897766.jpg

Answered: - 1000 kg/m) flows from a large Q6:…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A straight pipe has a daimater of 25 mm, a roughness height of 0.1 mm, and is inclined upward at and angle of 10 degrees. The water temperature is 20 degrees C. a. If the pressure at a given section is to be maintianed at 550 kPa, determine the pressure at a section 100 m downstream for flows of 2L/min and 20L/min.
A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at section 2. Section 1 is 3.6 m below section 2 and the pressures are 90 KPa and 60 KPa, respectively. If the discharge is 150 lit/sec, determine the head lost and the direction of flow.
Oil relative density (rd = 0.88) flows in an inclined pipe at a rate of 0.15 m/s as shown in Fig. If the differential reading in the mercury manometer is 915 mm, calculate the power that the pump supplies to the oil if head losses are negligible.
3. What is the volumetric flow rate between two plates if the top plate is pulled, while keeping the bottom plate stationary, and simultaneously imposing pressure p0 on the left endof the channel, and pressure p0 + ∆p (∆p > 0) on the right end of thechannel.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank. a)Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. b) What gage pressure p1 in kPa, is needed to provide the given flow rate?
O1: A stream of water of diameter d = 0.1 m flows steadily from a tank of diameter D= 1.0 m. Determine The Weight Flowrate, needed from the inflow pipe if the water depth remains constant, 0 — d=010m
Define net positive suction head and required net positive suction head, and explain how these two quantities are used to ensure that cavitation does not occur in a pump.
Water flows through the galvanized iron pipe system whose diameter is 0.75 inches and flow rate is 0.020 cfs. Do you agree with the fact that friction losses in the straight parts of the piping system are negligible with respect to losses to fittings?
Calculate the total head of the system below. Assume a flow of 70 m³/h and that the pressure drops in the suction and discharge are 3 m and 4 m, respectively. ZA = 15m, ZB = 5m and ZC = 5m.
A 20mm diameter commercial steel pipe, 30m long is used to drain an oil tank. Determine the discharge when the oil level in the tank is 3m above the exit of the pipe. Neglect minor losses and assume f = 0.12.
A diverging tube discharges water from reservoir at a depth of 10m below the water surface. The diameter of the tube graduallyincreases from 150 mm at the throat to 225 mm at the outlet.Neglecting friction, determine the maximum possible rate ofdischarge through this tube.
(a) Prove that the loss of pressure head for the viscous flow through a circular pipe is givenby h. (b) Determine (i) the pressure gradient, (ii) the shear stress at the two horizontal parallelplates, and (iii) the discharge per meter width for the laminar flow of oil with a maximumvelocity of 1.5 m/s between two horizontal parallel fixed plates which are 80 mm apart. Takeviscosity of oil as 1.962 Ns/m2.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

- 1000 kg/m) flows from a large Q6: Water (p tank through a large pipe that splits into two imaller pipes as shown in Fig. If viscous effects are negligible, determine the flow rate from the tank and the pressure at point (1). 3 m 0.03-m diameter 0.05-m diameter 0.02-m diameter