Q4) Water at 10°C fNows from a large reservoir to a smaller one through a 5-cm-diameter cast iron piping system, as shown in Fig. Determine the elevation z, for a flow rate of 6 L/s. Note that Properties The density and dynamic viscosity of water at 10 e are pm 999.7 kg/m and p= 1.307 x10° kg/m-s. 2, ? Sharp-edged „entrance, K -05 Standard elbow, flanged K-03 D-5 cm 9 m -Control volume boundary Gale valve. fully open K-02- CS CarmscaTET Exit, K. - 1.06

Q4) Water at 10°C fNows from a large reservoir to a smaller one through a 5-cm-diameter cast iron piping system, as shown in Fig. Determine the elevation z, for a flow rate of 6 L/s. Note that Properties The density and dynamic viscosity of water at 10 e are pm 999.7 kg/m and p= 1.307 x10° kg/m-s. 2, ? Sharp-edged „entrance, K -05 Standard elbow, flanged K-03 D-5 cm 9 m -Control volume boundary Gale valve. fully open K-02- CS CarmscaTET Exit, K. - 1.06

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The ideal fluid (water) taken from the infinitely sized chamber A with the chamber-pipe system in…

Q: At a point in a 15 cm diameter pipe, 2.5m above its discharge end, the pressure is 250 kPa, If the…

Q: Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe…

Q: For the horizontal laminar internal flow through a pipe of diameter (d), if the veloci -1 dP (r)%3D…

Q: determine the flowrate through the hole. m3/s Would the ball become noticeably softer during a…

Q: The system in Fig. consists of 1200 m of 5 cm castiron pipe, two 45° and four 90° flanged…

A: For water at 20 degree-Celcius, take

Q: A cylindrical tank 0.9 m in radius rests atop a platform 6 m high. Initially the tank is filled with…

A: The initial speed of the stream is u=2gh=2×9.81×3=7.67 m/s From the conservation of energy…

Q: Water, assumed incompressible, flows steadily throughthe round pipe in Fig. The entrance velocity is…

A: Given data constant entrance velocity u = U 0 the exit velocity approximates turbulent flow, u =…

Q: Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe…

Q: Water at 40°C flows horizontally through a constriction similar to that in Fig. S3.9 when the…

A: Given, Temperature of flow 40 C Pressure at section 1 , P1 = 35 KPa Diameter at section 1 , d1 =…

Q: 0.04 m diameter (1) 3 m (2) A Q2) Water is siphoned from a tank as shown in figure 2. If viscous…

A: Given: The diameter of pipe, d = 0.04 m The depth of point A, h = 3 m

Q: A storage contains liquid at depth y where y30 when the tank is half full, as shown below. Liquid is…

A: 1. Using 1st order O.D.E., Using Euler's method,

Q: Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe…

Q: Water falls vertically downward from an open faucet with an initial velocity of 66 cm/s. If the…

Q: Water at 20 ° C flows through a 5-cm-diameter pipe that hasa 180 °vertical bend, as in Fig. P3.43.…

A: Given data: Diameter of pipe = d = 5 cm Pressure at point 1 = P1 = 165 kPa Pressure at point 2 = P2…

Q: Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m3 ) is to be pumped through 50 m of pipe…

Q: Water flows through a venturi as shown in the figure at a flow rate of Q=49.7 L/s. The inlet and…

A: Given:- Water flowing through venturi meter Flow rate (Q) = 49.7 L/s = 0.0497 m3/s Inlet Diameter…

Q: A siphon consisting of a 3 cm diameter tube is used to drain water from a tank. The outlet end of…

Q: A vertical orifice is 10 cm. square and has an actual flow of 28 Ips with Cy= 0.95, C= 0.62 as shown…

A: The coefficient of discharge can be determined as,

Q: In Fig. P3.130 the fl uid is gasoline at 20 ° C at a weight fl owof 120 N/s. Assuming no losses,…

A: Given data To determine the gauge pressure at section 1-1

Q: N/m². The flow is steady, incompressible, and fully develc

Q: Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe…

A: for solution refer below images. Note:- since loss coefficient for abrupt expansion is not given i…

Q: A 2.4 m diameter tank is initially filled with water 5.5 m above the center of a 10 cm diameter,…

Q: Water at 40°C flows horizontally through a constriction similar to that in Fig. S5.9 when the…

A: Given data:-Pressure of water at bigger end, P1=35kPadiameter at bigger end, d1=0.5m⇒cross-sectional…

Q: Q4) Water at 10°C flows from a large reserveir to a smaller one through a 5-cm-diameter cast iron…

A: Q=6L/sD=5cmA=πD2/4=1.963X10-3 m2avg velocity, v:v=Q/pA=6x10-3/999.7X1.963X10-3v=3.057X10-3m/s…

Q: Water, assumed incompressible, flows steadily through the round pipe in Fig. P3.15. The entrance…

A: Given data: Entrance velocity, u = U0 Exit velocity, u = umax( 1 – r/R)1/7 Since the flow is steady,…

Q: The system in Fig. below consists of 1200 m of 5 cm cast iron pipe, two 45° and four 90° flanged…

Q: A smooth 8-cm-diameter pipe, 200 m long, connects tworeservoirs, containing water at 20°C, one of…

A: Given Diameter of the pipe is 8cm = 0.08m Pipe length = 200m Water temperature = 20o C Elevation…

Q: estimate the allowable distance Y if the allowable pressure in the systems is -188kPa (gage). aasume…

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: Q2: Water at 20°C (p= 998 kg/m, u= 1.003x10-3 N.s/m²) flows in a long horizontal commercial-steel 6…

A: Venturimeter is a practical application of Bernoulli's equation. Venturimeter consists of basically…

Q: Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe…

A: for solution refer below images.

Q: Water at 20 ° C is pumped at 1500 gal/min from the lower tothe upper reservoir, as in Fig. P3.180.…

A: Water temperature T = 20 0C Flow rate Q = 1500 gal/min = 3.342014ft3/sec Friction loss approximation…

Q: Q4 Water flows from a large reservoir to a smaller one through a 5cm diameter cast iron piping…

A: Given data as per the question Diameter of the pipe =5cm =0.05 m Flow rate =5L/s Dynamic viscosity…

Q: Water (density 1000 kg/m) flows through an inclined pipe of uniform diameter. The velocity. pressure…

A: According to information we have A sloping pipe of a uniform diameter flows through water (dansity…

Q: Water at 20 ° C is to be siphoned through a tube 1 m longand 2 mm in diameter, as in Fig. . Is there…

A: Draw the diagram for the problem. Here, the points 1 and 2 indicate the points in the siphon as…

Q: Q4/ In Fig. all pipes are 8-cm-diameter cast iron. Determine the flow rate from reservoir (1) if…

Q: A surge chamber 10m in diameter is situated at the down stream end of a low pressure tunnel 9.8km…

Q: For the horizontal laminar internal flow through a pipe of diameter (d), if the velocity profile (r)…

A: ζ = f8ρV2f = frction factorρ= densityV = avg. flow velocity

Q: A siphon consisting of a 2 cm diameter tube is used to drain kerosene oil from a large open tank.…

Q: If L =4.5 km, d- 40 mm and Az 100 m, what will be the flow rate of water in m'/hr. Make suitable…

Q: SAE 10 oil at 20 °C flows through the 4-cm-diameter verticalpipe of Fig. P6.30. For the mercury,…

A: Given data d=0.04 mh=0.42 mρ=870 kg/m3μ=0.104 kg/m·s

Q: Water at 10°C flows from a large reservoir to a smaller one through a 4-cm diameter galvanized iron…

A: To determine the elevation z1.

Q: Why an ideal flow of any fluid must satisfy continuity equation?

A: "An ideal flow of any fluid must satisfy the continuity equation." Because the continuity equation…

Q: Q2: The maximum flow velocity of water in a pipe is 2.4 m/s . The pipe has 0.2 cm diameter , and 15…

Q: Answer completely The Fanning equation and the Darcy-Weisbach equation both relate the pressure…

A: To Explain : The physical significance of the pressure drop and explain the reason behind the…

Q: Oil with a kinematic viscosity of 6 x 104 m2/s flows in a 0.9 m straight pipe at a rate of 0.05 m/s.…

Q: 7 In Fig. P3.137 the fluid is gasoline at 20°C at a wcight flux of 120 N/s. Assuming no losses,…

A: Calculate the discharge as follows:

Q: Determine the head loss due to friction of an oil of specific gravity 0.77 and viscosity 0.85 poise…

Q: Water, p 1000 kg/m³ and μ = 0.001 kg/m.s, is pumped be reservoirs at 5 liter/s through 125 m of 5…

Q: is the head, h in meter over the orifice is required?

A: given:flow rate Q=28lpsCC=0.62CV=0.95s.g=0.85

Concept explainers

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.

Question

Mechanical Engineering Subject : Fluid mechanics

Q4) Water at 10°C fNows from a large reservoir to a smaller one through a 5-em-diameter
cast iron piping system, as shown in Fig. Determine the clevation z, for a flow rate of 6 L/s.
Note that Properties The density and dynamic viscosity of water at 10 e are p= 999.7 kg/m
and p- 1.307 x10 kg/m s.
2, ?
Sharp-edged
entrance, K - 05
Standard elbow,
flanged, K - 03
D-5 cm
4m
Control
volume
boundary
Gale valve,
fully open
K= 02-
CS CarnscamÍ TET s
Bum
-Exit. K - 1.06

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Step 9

Step by step

Solved in 9 steps with 9 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
A pipe whose axis is horizontal, is full of water in motion. At a section A, the velocity of water is recorded as 54000dm/hrandd the pressure is equilavent tp 14.07m of water. if the pipe tapers gradually from 150mm diameter to A to 100mm diameter at B. determine the preesure at B.
SAE 30W oil at 20 ° C flows through the 9-cm-diameterpipe in Fig. P4.87 at an average velocity of 4.3 m/s. ( a ) Verify that the flow is laminar. ( b ) Determine the volumeflow rate in m 3 /h. ( c ) Calculate the expected reading hof the mercury manometer, in cm.
The system in Fig. consists of 1200 m of 5 cm castiron pipe, two 45° and four 90° flanged long-radius elbows,a fully open flanged globe valve, and a sharp exit into areservoir. If the elevation at point 1 is 400 m, what gagethe pressure is required at point 1 to deliver 0.005 m3/s of waterat 20°C into the reservoir?
(Restrictions on Bernoulli equation) A 0.256-m-diameter soccer ball, pressurized to 20.3 kPa, develops a small leak with an area equivalent to 0.006 mm2. If viscous effects are neglected and the air is assumed to be incompressible, determine the flowrate through the hole. m3/sWould the ball become noticeably softer during a 1-hr soccer game? YesNoIs it reasonable to assume incompressible flow for this situation? NoYes
1. in a section of horizontal piper with a diameter of 3cm the pressure is 5.21 kpa and water is flowing with a speed of 1.50m/s. the pipe narrows to 2.50cm. what is the pressure in the narrower region if water behaves like an ideal fluid of sensity 1000kg/m3 2. tensile stress a. the ratio of elasic modules to strain b. the applied force per crosssectional area c. the ratio of change in length to the orig length d. the strain per unit legth e. the same as force
Water flows at 20°C through a new cast iron pipe at a velocity of 4.2 m/s. The pipe is 400 m long and hasa diameter of 150 mm. Determine the head loss due to friction. Ans. 54.20 m (show the complete solution) Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet. E.g. (density, viscosity)Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness
The horizontal tube is 1 m long and 10 cm in diameter and is filled with a sample material. During a test, the upstream head h, falls from 200 to 180 cm in 4 hr, while h₂ is held constant at 15 cm. The diameter of vertical tube in which h, is measured is 40 cm. What is the indicated average hydraulic conductivity?
Oil of viscosity 10E-3 Pa-s and specific gravity 0.90, flows through 60 m of 100mm diameter pipe and the pressure drop 13.8 kPa. What will be the pressure drop for a second oil of viscosity 30E-3 Pa.s and the specific gravity 0.95 flowing at the same rate through the pipe? Assume the pipe wall to be smooth.A. 19.4 kPaB. 98.7 kPaC. 142.2 kPaD. 192.5 kPa
estimate the allowable distance Y if the allowable pressure in the systems is -188kPa (gage). aasume that the volume flow rate is 5.6 x 10^-3 m^3/s
Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc
Determine the head loss due to friction of an oil of specific gravity 0.77 and viscosity 0.85 poise is flowing through a pipe at the rate of 3.7 m/s. Assume the pipe diameter as 29 cm and the length of the pipe as 5618 cm. Oil Density (in kg/m3) Reynold's Number - Co-efficient of friction - Head loss due to friction