Try One - scene 7 of 7 The bar has a 90 mm by 20 mm rectangular cross section. If P = 80 kN, determine the force components perpendicular (N) and parallel (V) to a – a, the inclined surface area, and the 90 mm > normal and shear stress magnitudes acting on surface a – a. 62° a N kN V kN Ag-a mm2 P = 80 kN MPa MPa Try one 1st 2nd 3rd Enter attempt

Try One - scene 7 of 7 The bar has a 90 mm by 20 mm rectangular cross section. If P = 80 kN, determine the force components perpendicular (N) and parallel (V) to a – a, the inclined surface area, and the 90 mm > normal and shear stress magnitudes acting on surface a – a. 62° a N kN V kN Ag-a mm2 P = 80 kN MPa MPa Try one 1st 2nd 3rd Enter attempt

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In each case, the state of stress sx, sy, txy produces normal and shear stress components along section AB of the element that have values of sx = -5 kPa and txy = 8 kPa when calculated using the stress transformation equations.Establish the x and y axes for each segment and specify the angle u, then show these results acting on each segment.
The bar has a 100 mm by 15 mm rectangular cross section. The allowable normal and shear stresses on inclined 66° surface a – a must be limited to 50 MPa and 35 MPa, respectively. Determine the 100 mm magnitude of the maximum axial force P that can be applied to the bar, and determine the actual normal and shear Try one stresses acting on inclined plane a – a.
The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial distributed loading along its length of w = 8 kN/m. Two concentrated loads also act on the rod: P = 5 kN and Q = 7 kN. Determine the normal stress in the rod at x = 1.4 m. Assume a = 0.5 m and b = 1.2 m. A -> a Answer: 0 = i B W b C MPa Q
The solid circular rod has a cross-sectional area of 460 mm². It is subjected to a uniform axial distributed loading along its length of w= 8 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 5 kN. Determine the normal stress in the rod at x = 0.9 m. Assume a = 0.6 m and b = 1.0 m. B MPa a Answer: 0 = i b
The plate has a thickness of 20 mm and the force P = 3 kN acts along the centerline of this thickness such that d = 150 mm. Plot the distribution of normal stress acting along section a–a.
The long bolt passes through the 70.4-mm-thick plate. If the force in the bolt shank is 9.5 KN, then the average shear stress (MPa) along the cylindrical area of the plate defined by the section lines a-a is: O a. 0.00 O b. 21.00 O c. 2.39 O d. 4.77 O e. 1.19 18 mm b b 8 mm Time left 0:45:52 a 7 mm YouTube The wood beam has an allowable shear stress of 15 MPa, the maximum shear force V (kN) that can be lind to the cross section is:
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20oProperties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2
9 mm A .9 mm 96 mm 60 mm P 9 mm If the 9 mm hole is drilled through the plate determine the radius of the fillets such that the maximum stress value is the same for the hole %3D and the fillets for a applied force of P = 10 kN.
d2 mm FKN | 60 mm dlmm 10 mm 40 mm The shaft shown is subjected to the axial force(F) of 30 kN. If the shaft(diameter d2 =54 ) passes through the hole(diameter d1 = 55) in the fixed support A. Determine the average shear stress, Tavg (MPa), acting along the inside surface of the collar where it is fixed connected to the 54 mm diameter shaft.
Three rods jointly support a 8kN load. Assumingthat there was no stress in the rods before theload was applied, find the stress in each rod.θ = 25oα = 20o Properties:Modulus ofElasticityCrosssectionalAreaSteel 200 GPa 250mm2Bronze 83 GPa 250mm2 L = 2.75 m
The solid circular rod has a cross-sectional area of 410 mm². It is subjected to a uniform axial distributed loading along its length of w = 9 kN/m. Two concentrated loads also act on the rod: P = 3 kN and Q = 5 kN. Determine the normal stress in the rod at x = 0.5 m. Assume a = 0.7 m and b = 1.3 m. A B MPa x a Answer: 0 = i b
2. The cast iron pipe is filled with concrete and subjected to a compressive force of 80 kN. Determine the average normal stress in the concrete and the iron due to this loading. The pipe has an outer diameter of 70 mm and an inner diameter of 60 mm. Eiron = 100 GPa, Ec = 24 GPa. 80 kN 500 mm