11. A steel rod of 25 mm diameter is fitted inside a brass tube of 25 mm internal diameter and 375 mm external diameter. The projecting ends of the steel rod are provided with nuts and washers. The nuts are tightened up so as to produce a pull of 5 kN in the rod. The compound is then placed in a lathe and the brass is turned down to 4 mm thickness. Calculate the stresses in the two materials. |Ans. 7 N/mm', 7.8 N/mm²|

11. A steel rod of 25 mm diameter is fitted inside a brass tube of 25 mm internal diameter and 375 mm external diameter. The projecting ends of the steel rod are provided with nuts and washers. The nuts are tightened up so as to produce a pull of 5 kN in the rod. The compound is then placed in a lathe and the brass is turned down to 4 mm thickness. Calculate the stresses in the two materials. |Ans. 7 N/mm', 7.8 N/mm²|

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

5 decimal places Two identical plates of 61 mm wide and 6 mm thick is connected by a square pin with side dimension 14 mm. If a plate is subjected to a tensile force of 29 kN, determine the maximum tensile stress (MPa) developed in the plate. A thin-walled cylinder is subjected to an internal pressure P. What is the ratio of the tangential stress to longitudinal stress in the wall of the vessel?
A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb. Determine the magnitude and location of the highest bending and torsional stresses in the 1" diameter shaft.
Using 2 of the 3 given equations: σ = F/A ε = δ/L σ = E * ε calculate the original length, in mm, of a circular tube that experience a compression stress of 80 MPa . The deformation of the tube is 0.684 mm and E = 70 000 MPa. Make sure to write which equations of the three above you used.
5 decimal places 1. Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 51 kN if it developed a stress of 21 MPa. Take note that the inner diameter is 3/6 of the outer diameter. 2. Three identical plates of 67 mm wide and 7 mm thick is connected by a square pin with side dimension 17 mm. If the middle plate is subjected to a tensile force of 25 kN, determine the shear stress (MPa) developed in the pin. 3. Two identical plates of 61 mm wide and 5 mm thick is connected by a square pin with side dimension 19 mm. If a plate is subjected to a tensile force of 28 kN, determine the bearing stress (MPa) developed in the plate.
Calculate the principle stresses and the maximum shear stress.
A force of 400N is applied on a area of 20m ^2 . Determine the stress generated by the force .
why do you multiply by 16 in the shear stress?
The allowable stresses for the splice shown are the following: 150 MPa for shear of rivets, 1.35Fy for bearing,0.60Fy for tension and Fy = 250 MPa. Note: rivet holes are 2 mm bigger than the rivet diameter and the middleplate is 20 mm thick. Find the diameter of the rivets so that the joint capacity due to shear approximately equal to the bearingcapacity.a. 25.4 mm c. 28.65 mmb. 30.79 mm d. 36.97 mm Find the maximum safe value of P without exceeding the allowable shearing stressa. 773.6 kN c. 938.3 kNb. 878.1 kN d. 848.2 kN Find the maximum safe value of P without exceeding the allowable tensile stress.a. 579.3 kN c. 716.1 kNb. 495.5 kN d. 692.5 kN
Find the principal stresses value
: Determine the force necessary to punch a 10 mm dia. Hole in a 20 mm thick mild steel plate, if the shearing strength of mild steel is 10 N/ mm2. Also, state the nature and magnitude of the stress in the punch.
A line shaft rotating at 320 rpm is to transmit 35 kW power. The allowable shear stress for the shaft material is 56 N/mm2. Determine the diameter of the shaft?
A press is used to punch 10 holes per minute of 30 mm diameter hole from 25 mm thick plate. Determine the power needed to punch a hole if ultimate shear stress is 400 Mpa. Determine the following: The maximum force required to punch a hole, kN The power required to drive the press, kW