04: In figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide, (a) if the allowable stresses 200 MPa for bearing in the plate material and 120 MPa for shearing of the rivet, determine the minimum thickness of each plate. (b)Under the conditions

04: In figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide, (a) if the allowable stresses 200 MPa for bearing in the plate material and 120 MPa for shearing of the rivet, determine the minimum thickness of each plate. (b)Under the conditions

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The plate shown in the figure is fastened to the fixed member by three 10 mm diameter rivets.…

Q: A flanged bolt coupling consists of ten 20-mm diameter steel bolts spaced evenly around a bolt…

Q: Referring to figure assume that the diameter of the rivet that joins the plates is d = 20 mm. The…

Q: Q 4 For the figure below, the average shearing stress in each rivet is ..kPa (Hint: Two…

Q: A punch for making holes in steel plates is shown in Figure 4. Assume that a punch having diameter d…

Q: A flange bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm…

Q: Each of the four links in Figure 3 has an 8x36mm uniform rectangular cross section and each of the…

Q: timber beam, 80mm wide by 60mm high, is subjected to a vertical shear load of V = 40KN. Determine…

A: Given:b=80 mmh=160 mmV=40 KN

Q: A flanged bolt coupling is used to connect a solid shaft 94 mm in diameter to a hollow shaft 100 mm…

Q: A cylindrical pressure tank is fabricated by butt-welding 19 mm-thick plate with spiral seam shown…

A: For solution refer below images.

Q: Example 125. In figure below, assume that a 20-mm-diameter rivet joins the plates that are each 110…

A: Given data: Diameter of rivet, d = 20 mm. Width of the plate, w = 110 mm. Allowable bearing stress…

Q: " A thick steel cylinder which has an inside diameter of 1m is subjected to an internal pressure of…

Q: A flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in…

A: Given data: τ=60 MPad=10 mmD1=400 mmD2=300 mm Need to determine the value of loads P1 and P2 and…

Q: Calculate the shearing stress on the 8-mm-diameter bolt at A. Assume single shear. B D 60° 60° 25 cm…

Q: For the figure below, the average shearing stress in each rivet is .kPa (Hint: Two 22-mm-diameter…

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

Q: A flanged bolt coupling is used to connect a solid shaft 120 mm in diameter to a hollow shaft 100 mm…

Q: A drill rod with a diameter of 12 mm is made of high-strength steel alloy with a shear modulus of 80…

Q: A plate is fastened to a fixed member by four 25 – mm diameter rivets arranged as shown. Compute the…

A: Draw the free body diagram of the bar.

Q: The allowable stresses for the splice shown are the following: 150 MPa for shear of rivets, 1.35Fy…

A: Given Dataσs=150MPaFy=250MPat=20mmw=300mmσt=0.6Fy=150MPa

Q: An axial tensile load of 10kN is applied to a 12mm diameter bar. Determine the maximum shearing…

Q: 1. In the figure, assume that a 20-mm diameter rivet joins the plates which are 100 mm wide. a. If…

A: Given allowable bearing stress Ss=140 MPa and shear stress Sc=80 MPaThe diameter of the rivet d=20…

Q: Please give answer

A: Given data The width of the plate is w=150 mm The diameter of the rivet is d=20 mm The thickness of…

Q: Situation 3: Four plates, 10 mm thick each, are connected by 25-mm diameter rivets as shown. Assume…

A: Considering four plates having a thickness of 10 mm are joined by rivets having a diameter of 25 mm.…

Q: In figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm…

Q: 4. Determine the efficiency of the riveted butt joint with 20 mm main plate, 12 mm cover plates and…

A: Given data, tmp = Thickness of main plate = 20 mm = 0.02 m tcp = Thickness of cover plate = 12 mm =…

Q: Two strip of metal are pinned to gather as shown in fig below with a rod of 10 mm diameter. The…

A: Given Information: The diameter of the rod (d) = 10 mm The ultimate shear stress of the rod (S) = 60…

Q: The butt joint shown in the figure is connected using five 20 mm diameter bolt. If the tension force…

Q: the butt joint shown in the figure is connected using five 20mm diameter bolt. If the tension…

A: Given data: P=25 kNd=20 mm Need to determine the maximum shearing stress developed in the bolts.

Q: The plate shown in the figure is fastened to the fix member by three 10 mm diameter rivets. Compute…

A: Given: The diameter of the rivets is 10 mm. The maximum shear stress in the rivet is 70 Mpa. The…

Q: Assume that the axial load P = 40KN applied to the lap joint is distributed equally among the three…

Q: In Fig. below, the vertical shaft and the pulleys keyed to it may be considered to be weightless.…

A: GIVEN: WORKING SHEAR STRESS, τ= 64MPa diameter of disc A=250mm diameter of disc B=500mm diameter of…

Q: 6. As shown in the figure, a hole is to be punched out of a plate having an ultimate shearing stress…

A: Given:Ultimate shear stress of plate=300 MPaFor Part a: compressive stress in punch=400 MPahole…

Q: A coupling is used to connect a 51mm diameter plastic rod to a 35mm diameter rod as shown. If the…

Q: The members of the structure in Fig. weigh 200lb/ft. Determine the smallest diameter pin that can be…

Q: The lap joint shown is fastened by 6 − 20mm diameter rivets. Assuming that P = 200KN, determine (a)…

Q: A compound thick cylinder has a bore of 100 mm diameter, a common diameter of 200 mm and an outside…

Q: The bell crank CBA is connected to a pin support B in double shear with 8-mm diameter pin B and to…

Q: STRENGTH OF MATERIALS (NO LONG EXPLANTION NEEDED. RATE WILL BE GIVEN) Two blocks of wood, 50 mm…

Q: A 5 hp engine is transmitting power to a generator at 1800 rpm through a steel shaft. Determine the…

Q: In Figure 4.1, assume that a 21 mm diameter rivet joins the plates that are each 110 mm wide. The…

Q: 0. A hollow rivet has an outside diameter of 5 mm and an inside diameter of 3 mm. If the allowable…

A: Given Outer diameter, D = 5 mm Inside diameter, d = 3 mm Stress = 400 x…

Q: Problem: Use the elasticity theory to determine the maximum shearing stress, the angle of twist per…

A: Elasticity theory is concerned with the connection between forces applied to an item and the…

Question

a alll Asiacell
Google Translate
العربية -
الإنجليزية
الإنجليزية
04: In figure as shown
below, assume that a
35mm diameter rivet joint
the plates which are each
150mm wide, (a) if the
allowable stresses 200
MPa for bearing in the
plate material and 120 MPa
for shearing of the rivet,
determine the minimum
thickness of each plate.
(b)Under the conditions
specified in part (a) what is
the largest average stress in
the plate.
تحويل الصوت إلى نص
محادثة
كاميرا
العربية

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Is the axial stress generally smaller than the stress developed by shear?
The bolted connection illustrated below comprises one bolt and two plates. The bolt, which has a diameter of 20 mm, is threaded through a 22- mm diameter hole in both plates. The shear stress of the bolt is 78,000 MPa. Based on this information, determine the following What is the largest force F that can be placed on the joint without shearing the bolt? what is the normal stress, at the gross section area, in each plate? what is the normal stress, at the net section area, in each plate? what is the bearing (or contact) stress between the bolt and each plate?
A double riveted butt joint, in which the pitch of the rivets in the outer rows is twice that in the inner Rows, connects two 16mm thick plates with two cover plates each 12 mm thick. The diameter of rivets is 22 mm. Determine the pitches of the rivets in the two rows if the working stresses are not to exceed the following limits: Tensile stress in plates =100 MPa; Shear stress in rivets =75 MPa; and bearing stress in rivets and plates =150 MPa. Make a fully dimensioned sketch of the joint by showing at least two views.
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. Draw appropriate FBDs showing how the internal forces were determined. A square bar (side length = 50 mm) is welded to a fixed supporting slab. A 30-mm diameter pin is inserted in the bar. When the loading shown is applied, determine the following: a. maximum normal stress in the bar (MPa) and bearing stress between the pin and the bar (MPa)b. stress in the weld between the bar and the supporting slab (MPa)c. shear stress in the pin (MPa) and shear stress in the bar (MPa)
Using the shear formula, how can we check to see that the allowable shear stress is not exceeded?
A single bolt is used to lap joint two steel bars together. Tensile force on the bar is 20,000 N. Determine the diameter of the bolt required if the allowable shearing stress is 70 MPa?
For the two-dimensional stress fi eld shown in Fig. it isfound thatσxx = 3000 lbf/ft2 σyy = 2000 lbf/ft2σxy = 500 lbf/ft2Find the shear and normal stresses (in lbf/ft 2 ) acting onplane AA cutting through the element at a 30° angle asshown.
Using the shear formula, how can we check that the allowable shear stress is not exceeded?
A hole is to be punched out of a plate having a shearing strength of 281.48 N/mm². The compressive stress in the punch is limited to 351.85 N/mm² then the maximum thickness of the plate from which a hole 63.5mm in diameter can be punched is (in mm)
n figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide.(a) if the allowable stresses 200 MPa for bearing in the plate material and 120MPa for shearing of the rivet, determine the minimum thickness of each plate.(b)Under the conditions specified in part (a) what is the largest average stress in the plate.
Distinguish between simple and indirect shear stress?
For a body under three dimensional stress state, describe the procedure for obtaining the absolute maximum shearing stress at a given point.