11.9 (A/B). Develop from first principles an expression for the instantaneous stress set up in a vertical bar by a weight W falling from a height h on to a stop at the end of the bar. The instantaneous extension x may not be neglected. A weight of 500 N can slide freely on a vertical steel rod 2.5 m long and 20 mm diameter. The rod is rigidly fixed at its upper end and has a collar at the lower end to prevent the weight from dropping off. The weight is lifted to a distance of 50 mm above the collar and then released. Find the maximum instantaneous stress produced in the rod. E = 200 GN/m³. [114 MN/m²]

11.9 (A/B). Develop from first principles an expression for the instantaneous stress set up in a vertical bar by a weight W falling from a height h on to a stop at the end of the bar. The instantaneous extension x may not be neglected. A weight of 500 N can slide freely on a vertical steel rod 2.5 m long and 20 mm diameter. The rod is rigidly fixed at its upper end and has a collar at the lower end to prevent the weight from dropping off. The weight is lifted to a distance of 50 mm above the collar and then released. Find the maximum instantaneous stress produced in the rod. E = 200 GN/m³. [114 MN/m²]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The assembly shown consists of an aluminum shell (Ea= 10.6 * 106psi, αa=12.9 *10–6/°F) fully bonded to a steel core (Es= 29 * 106psi, αs= 6.5 *10–6/°F) and is unstressed. Determine (a) the largest allowable change in temperature if the stress in the aluminum shell is not to exceed 6 ksi, (b) the corresponding change in length of the assembly.
A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb. Determine the magnitude and location of the highest bending and torsional stresses in the 1" diameter shaft.
Problem No. 2 A cylindrical boiler with an outside diameter of 2.75 m and a wall thickness of 32 mm is made of a steel alloy that has a yield stress of 340 MPa. Determine: (a) the maximum normal stress produced by an internal pressure of 2.3 MPa.(b) the maximum allowable pressure if a factor of safety of 4.5 with respect to yield is required
answer this ; The factors of safety predicted at point H by the maximum shear stress theory of failure (Tresca criterion)
At a temperature of 20 °C there is a gap ∆ = 0.2 mm between the lower end of the brass bar and the slab rigid suspended from the two steel bars. Neglecting the mass of the slab, determine the stress in each bar when the temperature of the assembly rises to 100°C Answer: σsteel = 15.462MPa (t), σbronze= 20.615MPa(c),
A steel rod is to withstand a pull of 10,000 pounds. If the ultimate stress is 50,000 psi and yield stress of 35,000 psi with a factor of safety of 4 and 2 based on ultimate and yield respectively, determine the required diameter of the rod.
A steel [E=200 GPa] rod with a circular cross section is 10 m long. Determine the minimum diameter required if the rod must transmit a tensile force of 260 kN without exceeding an allowable stress of 240 MPa or stretching more than 10 mm.
Solve Prob A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is made of steel (Es5 29 3 106 psi, αs5 6.5 3 10–6/°F) and portion BC is made of aluminum (Ea5 10.4 3 106psi, αa5 13.3 3 10–6/°F). Knowing that the rod is initially unstressed, determine (a) the normal stresses induced in portions AB and BC by a temperature rise of 70°F, (b) the corresponding deflection of point B assuming that portion AB of the composite rod is made of aluminum and portion BC is made of steel.
2. A steel wire 30 ft long, hanging vertically, supports a load of 500 lbf. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 20,000 psi and the total elongation is not to exceed 0. in. Assume E = 29 × 106 psi.
The rigid bar CDE is attached to a pin support at E and rests on the 30 mm diameter brass cylinder BD. A 22-mm-diameter steel cylinder AC passes through a hole in the bar and is secured by a nut which is snugly fitted when the temperature of the entire assembly is 20 °C. The temperature of the brass cylinder is then raised to 50 °C while the steel rod remains at 20 °C. Assuming that no stresses were present before the temperature change, determine the stress in the cylinder. Cylinder AC: Steel (E = 200 GPa, a = 11.7 x 10-6/ °C) Cylinder BD: Brass (E = 105 GPa, a = 20.9 x 10-6/ °C) Further consider cylinder AC an unpressurized steel storage tank having outer diameter of 250 mm, wall thickness of 5 mm and ultimate strength of 420 MPa. Determine the maximum height h to which it can be filled with water if factor of safety 4 is required. Density of water is 9810 N/m3.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 22 ksi, and the normal stress in steel rod (3) must be limited to 13 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 7 kips, Q = 2 kips, R = 16 kips and S = 20 kips.
A conpound bar is constructed from threa barg 50 mm wida by 10 mm thick fastened together to form a bar 50 mm wide by 30 mm thick. The middle bar is of Alumioum alloy for which E = 70 GN / m ^ 2 and the outside bars are of brass with E = 100 GN / m ^ 2, If the bars are Initially fastened at 18 ° C and the Temperature of the whole assembly is then raised to 50 ° C, determine the stresses set up in the brass and the Aluminum. α (B) = 18 x per ° C and α (Al) = 22 x per "C. (b) What will be tho changes in these stresses if an extemal compressive load of 10 kN is applied to the compound bar at the higher Temperature?