112. Determine the weight of the heaviest ©ylinder which can be placed in the position shown in Fig. P-112 without exceeding a stress of 50 MN/m2 in the cable BC. Neglect the weight of bar AB. The cross-sectional area of cable BC is 100 mm?. 6 m Figure P-112. B

112. Determine the weight of the heaviest ©ylinder which can be placed in the position shown in Fig. P-112 without exceeding a stress of 50 MN/m2 in the cable BC. Neglect the weight of bar AB. The cross-sectional area of cable BC is 100 mm?. 6 m Figure P-112. B

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.9.30P

See similar textbooks

Related questions

Q: Current Attempt in Progress The rectangular bar is connected to the support bracket with a…

A: Givend=11mmw=70mmt=10mmτ=100MPa in pinσ=150 MPa in barσ=140 MPa in bracket

Q: 10. The homogeneous bar ABC that weighs 5000 Ib is supported by a smooth pin at C and a cable that…

Q: Reqd: Determine e of A relative to D Gst = 12 x 106 psi MN ]b• ft 2-in. diameter 1000 lb · ft 900 lb…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: Answer: The maximum load that can be supported by the structure: P = 29.046 kN

Q: Find the stresses which may induced in each rod if temperature is increases by 70°C. Aluminum Bronze…

Q: The rectangular reinforced concrete column is reinforced with 6- 20 mm steel bars as shown. If b =…

A: Given Data B=250 mm D=400 mm d=20 mm(steel bar) P=400 kN

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A₁ = 4350 mm² and an…

A: To find: The maximum load that can be supported by the structure without exceeding either allowable…

Q: The cross-sectional area of each member of the truss is 42 cm2. в L. C E 6m 100 kN 300 kN Determine…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: From the figure as shown, determine the stress in psi at the top surface of the second cylinder.…

Q: PROBLEM 1.1 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown.…

A: Given that , d1=30mmd2=50mm

Q: Determine the stress in member KE for the truss loaded and supported as shown in figure (2). Note…

A: Given Data AkE=917 mm2

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ - 3800 mm² and an…

Q: 36. A mild steel bar is 40cm long. The lengths of parts of AB and BC of bar 20cm each. It is loaded…

Q: A 150-mm-long bronze tube, closed at its ends, is 80 mm in diameter and has a wall thickness of 3mm.…

Q: View Policies Current Attempt in Progress Two solid cylindrical rods (1) and (2) are joined together…

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 8) Determine load P that…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

A: Answer: The maximum load that can be supported by the structure without exceeding either allowable…

Q: : The homogeneous bar ABCD shown in Fig., is -ported by a cable that runs from A to B around the…

A: ∑FH=0TAB cos 30°=RD sin 50°RD= 1.1305 TAB∑FV=0TAB sin 30°+TAB+TC+RD cos 50°=WTAB sin…

Q: The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast= 1000 mm2, Est…

Q: A 10-m section of steel rail has a cross-sectional area of 7500 mm2. Both ends of the rail are tight…

Q: -bar rigidly fixed at its both ends uniformly tapers from 90 er. What will be the maximum stress…

A: This explanation is given below

Q: circular tube AB is fixed at one end andfree at the other end. The tube is subjected to axialforce…

Q: Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 2000 mm² and an…

Q: The rigid bar ABC shown in Fig. is hinged at A and supported by a steel rod at B. Determine the…

Q: At 20°C, there is a gap d = 0.2 mm between the lower end of the bronze bar and the rigid slab…

Q: Que 1.23. A steel rod of 3 cm diameter is enclosed centrally in a hollow copper tube of external…

Q: The strong room of a school where an exam question papers are kept is made up ofrectangular metal…

A: Let b =Width =10mm σc =Compressive stress =-20MPa i) Calculate breadth Let d= breadth…

Q: The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast= 1000 mm?, Est…

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.250 in., and each side…

Q: 5) Bars CE and DE in the truss have a cross-sectional area A = 25 cm?. Find the normal stress in…

A: Truss is a group of two forces. Only at the joints are forces applied. The forces in truss members…

Q: The 65 kg tag is supported by cables AB and BC, as shown in the image, which have diameters of 1.5…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat…

Q: 3 a M The scheme of supporting of the absolutely rigid body is shown in the picture. The minimal…

A: Given data: The value of a is a = 1.6 m. The magnitude of the moment is M = 8 kN-m. The admissible…

Q: A cylindrical tank has an inner radius of 750mm and length of 3.0m. Determine its minimum thickness…

Q: Rigid bar ABC supports a weight of W = 26 kN. Bar ABC is pinned at A and supported at B by rod (1),…

A: Free body diagram

Q: The homogenous bar ABCD shown in the figure is supported by a cable that runs from A to B around the…

A: Draw free-body diagram of the given bar. Apply force equilibrium in horizontal direction.…

Q: 1- Calculate the stresses in members CE, DE, and DF. The cross-sectional area of each member is 1200…

Q: 2. A replacement disc consists of the tube Cwith larger diameter of 4 cm, the cylindrical core B…

Q: An aluminum [E-9600 ksi] control rod with a circular cross section must not stretch more than 0.34…

Q: Rigid bar ABC supports a weight of W 50 kN. Bar ABC is pinned at A and supported at B by rod (1),…

Q: A retaining wall 6 ft high is constructed ofhorizontal wood planks 2.5 in. thick (actual…

A: a draw the free body diagram here h = 6 ft is the length of the span s is the thickness of the…

Q: The homogeneous bar ABCD shown in the Figure is supported - by a Cable that runs from A to B around…

Q: A pulley is supported by a circular pin at A. The pin has a diameter of d = 0.375 in., and each side…

Q: Q3) A pillar crane, shown in below, is fastened to the foundation by means of 16 identical bolts…

Q: Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load Pat pin…

Q: 111. A homogeneous 150-kg bar AB carries a 2-kN force as showE in Fig. P-111. The bar is supported…

A: Given:- Weight of bar=150 kg Diameter of cable CD=10mm To find:- Stress in cable

Q: Mcq: the maximum shar stress in contact between steel spheres pressed together lies? 1-at the…

A: Ans: 3 is correct. Under the contact surface

Concept explainers

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.

Question

What is the answer on this question?

112. Determine the weight of the heaviest Oylinder which can be
placed in the position shown in Fig. P-112 without exceeding a stress of
50 MN/m2 in the cable BC. Neglect the weight of bar AB. The
cross-sectional area of cable BC is 100 mm?.
-6 m
-6 m
Figure P-112.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A cylindrical tank has an inner radius of 750mm and length of 3.0m. Determine its minimum thickness (to nearest mm) if it is subjected to an internal pressure of 150kPa and tangential stress is not to exceed by 12MPa. Indicate the free body diagram
The rigid beam is supported by the three suspender bars. Bars AB and EF are made of aluminum and bar CD is made of steel. If each bar has a cross-sectional area of 450 mm2, determine the maximum value of P if the allowable stress is (sallow)st = 200 MPa for the steel and (sallow)al = 150 MPa for the aluminum. Est = 200 GPa, Eal = 70 GPa.
A composite section will be used to support a heavy axial load of P = 800 kN with a rigid plate at the top of the section. Determine the average compressive stress (MPa) in the brass section. Use h = 25mm.
The A-36 steel column, having a cross-sectional area of 10500 mm2, is encased in high-strength concrete as shown. If an axial force of 300kN is applied to the column, determine the compressive stress in the concrete and in the steel. Es = 210GPA and Econc = 29 GPA.
Answer the following. If the allowable bearing stress for the material under the supports at A and B is σb = 820 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 650 lb/ft, a = 10 ft, and b = 5 ft.
Consider the wooden member subjected to a tensile load P = 11.0 kN. Determine the magnitude of the normal force at the inclined section shown.
A solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the limiting stress of the bar is 27.24 kPa determine the cross sectional area of the steel square bar and its dimensions.
Determine the load that can be applied at the end of the rigid bar if the stressin either spring shown in the figure shall not exceed 200MPa. Present detailed drawings/FBD’s illustrating your solution.
A spherical and cylindrical gas tank has the same inner radius of 1.5 m. Which of the two tanks can resist a higher internal pressure if both tank’s allowable stress (tangential stress for the cylindrical) is equal to 15 MPa, and its thickness is 20mm? show FBD
If the allowable bearing stress for the material under the supports at A and B is σb = 610 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 4 in. by 4 in. The reactions at the supports are vertical. Assume w = 650 lb/ft, a = 10 ft, and b = 5 ft.
Determine the size of square bearing plates A′ and B′ required to support the loading. Take P = 1.5 kip. Dimension the plates to the nearest 1 2 in. The reactions at the supports are vertical and the allowable bearing stress for theplates is (sb)allow = 400 psi.
The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends. If there is no load in the members when T1 = 50°F, determine the average normal stress in each member when T2 = 120°F. Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in2.