Que 1.23. A steel rod of 3 cm diameter is enclosed centrally in a hollow copper tube of external diameter 5 cm and internal diameter 4 cm. The composite bar is then subjected to an axial pull of 45000 N. If the length of each bar is equal to 15 cm. Determine : i. ii. Load carried by each rod. E for steel = 200 GPa and for Copper = 100 GPa. The stresses in the rod and the tube.

Que 1.23. A steel rod of 3 cm diameter is enclosed centrally in a hollow copper tube of external diameter 5 cm and internal diameter 4 cm. The composite bar is then subjected to an axial pull of 45000 N. If the length of each bar is equal to 15 cm. Determine : i. ii. Load carried by each rod. E for steel = 200 GPa and for Copper = 100 GPa. The stresses in the rod and the tube.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.2 A steel rod of 30 mm diameter is enclosed centrally in a hollow copper tube of external diameter 40 mm and 5 mm thick. The composite bar is then subjected to an axial pull of 45 kN. If the length of the compound rod is 150 mm, and the elasticity moduli are Est = 200 GPa and Ecu= 100 GPa. determine: 1.2.1 The stresses in the rod and tube 1.2.2 The load carried by the rod and that carried by the tube 1.2.3 The elongation of the compound rod.
The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
(a) Two vertical rods, one of steel and other of copper are each rigidly fixed at the top and 60 cm apart. Diameters and lengths of each of the rod are 3 cm and 3.5 cm, respectively. A crossbar fixed to the rods at the lower ends carried a load of 6000 N such that the crossbar remains horizontal even after loading. Find the stress in each rod and the position of the load on the bar. Take E for the steel as 2 x 10° N/mm² and for copper as 1 x 10° N/mm?.
1. Determine the internal stresses developed in bars JH and HY when bar JH experiences a change in temperature of -250•C. Bar JH is made of aluminum, while bar HY is made of steel. Both bars have the same cross-sectional area. Note: Pin H is connected to a wheel that is restricted to move along the inclined slope. J 450 H 1 m 250 Y 2 m Material a (/°С) E (GPa) Steel 11.9 x 10-6 200 Aluminum 22.5 x 10-6 70
An engineering machine component operating in a high temperature environment consists of a copper pipe having a cross-sectional area of 2 000 mm² and 0.3 m long, which is placed between two rigid caps. Four M22 steel bolts are symmetrically arranged around the tube and parallel to the axis of the tube and are lightly tightened. 3.1 Find the stress in the pipe and the bolts if the temperature of the assembly is increased from 25 °C to 95 °C. 3.2 What load will each bolt carry at the raised temperature? 3.3 Make a neat sketch of the assembly. (Est = 200 GPa, Ecu – 100 GPa, as: = 12 × 10-6/ °C, acu = 16 × 10-6/ °C)
1. A 60-mm diameter steel tube with a wall thickness of 3 mm just fits in a rigid hole. Determine the tangential stress developed if an axial compressive load of 12 kN is applied. Use v = 0.30 and E = 200 GPa. Answer: 0 = 6.37 MPa 2. A 200-mm long bronze tube closed at both ends fits without clearance in a 70-mm hole in a rigid block. It has a diameter of 70 mm and a wall thickness of 5 mm. The tube then sustained an internal pressure of 4.5 MPa. Use v = 0.33 and E= 83 GPa. Compute the tangential stress in the tube. Answer: Ot = 5.20 MPa
3. An axial pull of 35000 N is acting on a bar consisting of three lengths as shown below. If the Young's Modulus is 2.1 x 105 N/mm2. Determine (i) Stresses in each section, and; (ii) Total extension of the bar. Section 3 Section 2 Section 1 35000 N 35000 N 2 cm DIA 3 cm DIA 5 cm DIA k-20 cm- 25 cm -22 cm-
Question 3 - Strain Energy A brass tube with an outside diameter of 20 mm and 4 mm wall thickness is 80 mm long.It is joined to the end of a solid brass rod with a diameter of 20 mm and 120 mm long toform a compound assembly. This assembly is subjected to tension due to a mass of 150kg moving at a speed of 0.4 m/s.3.1. Determine the stresses induced in the rod and the tube respectively.3.2. Determine the change in length of each part, as well as the total change in length ofthe assembly.3.3 Determine the equivalent impact load (in kg) required to have the same effect(produce the same amount of energy) if falls freely from a height of 10 cm onto acollar attached to the bottom of the assembly if the assembly is vertically attachedat its top.3.4 How much strain energy is absorbed by each section of the assembly?(For brass: E = 100 GPa and α = 18×10-6/ 0C)
The inner diameter of a cylindrical pressure vessel is 400 mm. When subject to pressure, the hoop stress in the cylinder wall is 40 MPa. For the material of construction E = 200 GPa and Poisson's ratio = 0.3. The %3D increase in inner diameter is, O a. 0.016 mm b. 0.08 mm O c. 0.068 mm O d. 0.04 mm
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. The diameter of rod (1) is d1 = 1.66 in. and the diameter of rod (2) is d2 = 2.68 in. Determine the normal stresses in rods (1) and (2). Assume P = 17 kips and Q = 29 kips. Use positive for tensile stress and negative for compressive stress.
A cylindrical tank steel pressure vessel 200mm in radius and 4.0m in length, is subjected to an internal pressure of 3.0 MPa. Determine the thickness of tank (nearest mm) if the following stresses are not to be exceeded: tangential stress of 45 MPa and longitudinal stress of 30 MPa. and also show the free body diagram
A steel rod of circular cross section will be used to carry an axial load of 89 kips. The maximum stresses in the rod must be limited to 36 ksi in tension and 16 ksi in shear. Determine the required diameter for the rod.