18 |A vertical jet of water impinges on a horizontal disk as shown. The disk assembly mass is 30 kg. When the disk is 3 m above the nozzle exit, it is moving upward at U = 5 m/s. Compute the vertical acceleration of the disk at this instant. U = 5 m/s -M = 30 kg CS moving at speed U h = 3 m - A = 0.005 m² V = 15 m/s

18 |A vertical jet of water impinges on a horizontal disk as shown. The disk assembly mass is 30 kg. When the disk is 3 m above the nozzle exit, it is moving upward at U = 5 m/s. Compute the vertical acceleration of the disk at this instant. U = 5 m/s -M = 30 kg CS moving at speed U h = 3 m - A = 0.005 m² V = 15 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The water jet in figure, moving at 15 m/s, is split so that one-third of the water moves towardA. Calculate the magnitude and direction of the force on the stationary splitter.
Two geometrically similar pumps are running at the same speed of 1000 rpms One pump has impoller diameter of 300 mm and lift water at the rate of 0.02 m3 against a head of 15 m Determine the head and impeller diameter of the other pump to deliver half the discharge.
A jet of water 4cm diameter enters a fixed curved vane with a velocity of 50 metres/sec at an angle 20 degree to the horizontal. Find the normal and tangential forces exerted by the jet, if it leaves the vane at angle 15 degree to the horizontal
A fire hose discharges water through a nozzle having a diameter of 2.5cm. The head lost in the nozzle is 4% of the velocity head in the jet. If the gage pressure at the base of the nozle is 400kpa, find the flow and the maximum horizontal range to which the stream can be thrown.
The scoops of the Pelton turbine deflect the water jet by 25°. Geometric head 500m, absolute velocity m at the entrance 100 tangential velocity 50 The relative velocities at the entrance and exit of the impeller are approximately equal to each other. Find the hydraulic efficiency. (gravity acceleration= 9.81)
A water jet of diameter 3 cm is striking on a inclined. The velocity of the water is 56 m/s. Calculate the force exerted on the plate if the inclination is 50°.
A cylindrical tank discharges water at 20^O C through a well-rounded orifice to hit an inclined plate as shown in the figure. Determine the components of the force exerted by the fluid jet on the plate inclined at 60^O from the horizontal.( Assume the external and internal pressures are the same)
| The cross-sectional area is 25 square centimeter of water jet under the velocity of 35 meter per second and strikes tangentially a curved plate. The curvature angle of plate at the outlet is 120° with the x-axis. Find the force exerted by the get on the plate in the direction motion. Solve the problem, when the case of the plate is stationary and plate is moving in the direction of jet with the velocity of 15 meter per second.
Momentum Water flows through a horizontal, 180° pipe bend as is illustrated in the Fig. The flow cross‐sectional area is constant at a value of 9000 mm2. The flow velocity everywhere in the bend is 15 m/s. The pressures at the entrance and exit of the bend are 210 and 165 kPa, respectively. Calculate the horizontal (x and y) components of the anchoring force needed to hold the bend in place.
A jet of freshwater strikes a series of vanes of a turbine at 25° with the direction of motion and leaves it at 150° absolute with the direction of motion. The absolute inlet velocity of the jet is 25 m/s and the vanes move at a velocity of 10 m/s. Ignore friction across the vanes. Calculate:1. the vane inlet angle.
find a and b. A jet of water of diameter 50 mm, having a velocity of 30 m/s strikes a curved vane which is moving with a velocity of 15 m/s. The jet makes an angle of 30º with the direction of motion of vane at inlet and leaves at an angle of 120º to the direction of motion of vane at outlet,Calculate: a) Vane angles, if water enters and leaves the vane without shock b) work done per second per unit weight of water striking the vanes per second.
Two geometrically similar pumps are running at the speed of 1500rpm and 3000rpm. One pump has an impeller diameter of 0.40 m and lifts water at the rate of 0.03 liters/sec against a head of 20 meters. Determine the head, discharge and ratio of powers of said pump of diameter 0.25m.