2- Figure 1 illustrates the first threestages of a typical AM receiver,calculatea- The total gain in ration and dB?b- Gain or Attenuation in dB forthe three stagesindividual?с- Рі, Р, and P.ur ?outd- P1dBm> P2,dBm and Pout, dBm ?Pin=1pWP1P2IF AmplifierAp3=10,000PoutRF AmplifierАp -100MixerAp2=0.2Figure 1: AM receiver

We are authorized to answer only three subparts at a time so i am answering only 3 subparts please…

Answered: 2- Figure 1 illustrates the first three…

2- Figure 1 illustrates the first three stages of a typical AM receiver, calculate a- The total gain in ration and dB? b- Gain or Attenuation in dB for the three stages individual?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. A line has a signal-to-noise ratio of 120 and a bandwidth of 1800 KHz. Compute the maximum data rate supported by this line? 2. A signal has passed through four cascaded amplifiers, each with 8 dB gain. Compute the total gain? How much is the signal amplified? 3. Compute the theoretical capacity of a channel with a Bandwidth 65 KHz and SNR dB = 70 [
A receiver with a 75-ohms input resistance operates at a temperature of 31°C. The received signal is at 89 MHz with a bandwidth of 6 MHz. The received signal voltage of 8.3 µV is applied to an amplifier with a noise figure of 2.8 dB. Find (a) the input noise power, (b) the input signal power, (c) S/N, in decibels, (d) the noise factor and S/N of the amplifier, and (e) the noise temperature of the amplifier.
The amplitude of the modulating tone is decreased in the above example until the to-tal power is 45 kW. Assuming that the carrier power remained constant, compute thenew modulation index and transmission efficiency.
Find the normalized autocorrelation sequence of the following signal:x(n) = 1, for -3 ≤ n ≤ 3, and equals 0 for other values of n.b) For a recorded data, y(n), modeled by the following difference equation, derive an expression forryy(l) in terms of rxx(l):y(n) = 0.5x(n) + 0.5x(n-1)
Find the dB gain of an amplifier whose output voltage is 2.6 volts and whose input voltage is 0.09 volt. (Round your answer to the nearest decibel.)
What is the effect on the signal–to–noise ratio of a system (in dB) if the bandwidth is doubled, considering all other parameters to remain unchanged except the normal thermal noise only? The S/N will be ______. I need answer ASAP. Thank you!
After Steps 1-4 are completed in Ex. 3.6 and the link distance is 25 kilometers, the fade margin is Select one: a. 128 dB b. 25 dB C.-80 dBm d.11 dB Exercise 3.6 Link Budget and Fade Margin In this exercise, 2. In row 10, enter a link distance of 25 kilometers. Note that the path loss due to a 25 kilometer link is now 128 dB in the 2.4 GHz frequency. 3. In row 20, enter 128 for path loss in dB. 4. In row 23, change the radio receiver sensitivity to -80 dBm. Notice that the final received signal is now -69 dBm, and the fade margin is only 11 dB. 5. Try increasing the "radio transmitter output power" to see how the connection would fare and to determine how much power would be needed to ensure a fade margin of 20 dB. You can also change the other components such as antenna gain and cable loss to ensure a fade margin of 20 dB.
4. The front end of a television receiver, having a bandwidth of 7 MHz andoperating at a temperature of 27° C, consists of amplifiers having a gain of 15, followed by a mixer whose gain is 20. The amplifier has a 300Ω input resistor and a shot noise equivalent resistance of 500Ω . For the mixer; these values are 2.2kΩ and 13.5 kΩ, respectively, and the load resistance of the mixer is 470 kΩ. Calculate the equivalent noise resistance for this television receiver.5. A receiver connected to an antenna whose resistance is 50Ω has an equivalent noise resistance of 30Ω. What is the receiver’s noise temperature?
A/ Choose the correct answer1: ______ Sub-system collect data derived from many sensors on theSat and send it to the earth station.a) Telemetry b) thrust c) antenna d) stabilization2: ______ GEO Sat are required to cover the entire eartha) Two b) three c) four d) five3: An Amp has a noise temperature of 580ok, the equivalent is noisefigure in dB approximately is ______ .a) 2 dB b) 3 dB c) 4 dB d) 5 dB4: In a practical SAT, the transponder bandwidth is about ______ .a) 500 MHz b) 600 MHz c)700 MHz d) 800 MHz5: ______ Sub-system keeps the Sat antenna pointing in the rightdirectiona) antenna b) thrust c) stabilization d) Telemetry6: ______ Sat, it compromises between the lower and GEO. Sat it rotatesat 8000 km to 18000 kma) HEO b) MEO c) LEO7: An earth station receiver antenna with radius of 15m, efficiency 68%at operating frequency of 4.15 GHz, if the system noise temperatureis 88ok then the value of CNR in dB at the antenna approximatelyis ______ .a) 20 dB b) 30 dB c) 40 dB d) 50…
Determine the total noise figure referred to the input of a mixer stage that has a noise figure of 20 dB proceeded by an amplifier that has a noise figure of 8 dB and an available power gain of 25 dB A. 2.18 dB B. 2.81 dB. C. 1.28 dB D. 8.21 dB
A directional coupler configuration with four ports is shown in Figure Q4. A 15 dBm power source is connected to port 1 resulting in coupling factor, C = 15 dB, directivity, D= 25 dB, and insertion loss L=0.5 dB. If all ports are matched,determine the power in dB at ports 2, 3 and 4.
1.Assuming you are positioned at 5500 meters from the omnidirectional radio receiver you are jamming. Note that the transmitted signal you are jamming originates 3000 meters further away from the receiver. Signal transmitter’s EIRP is 14.5 dBW. Note that both the transmitter and jammer have line of sight, your jammer EIRP of 44W, however, will allow you to jam the receiver with what J/S ratio?.