2) The rigid bar is supported by two wooden posts and a spring as shown in the figure. If each of the post has unloaded length of 1-meter, cross-sectional area of 600mm? and modulus of elasticity E= 9.65GPa and the spring has stiffness k = 2000N/mm and un-stretched length of 1.02 meters, after the load of 50KN/m is applied to the bar, determine the force in the spring. 50 kN/m B 1 m 1m 1m

2) The rigid bar is supported by two wooden posts and a spring as shown in the figure. If each of the post has unloaded length of 1-meter, cross-sectional area of 600mm? and modulus of elasticity E= 9.65GPa and the spring has stiffness k = 2000N/mm and un-stretched length of 1.02 meters, after the load of 50KN/m is applied to the bar, determine the force in the spring. 50 kN/m B 1 m 1m 1m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The beam is made of a material having a specific weight ?. Determine the displacement and slope at its end A due to its weight. The modulus of elasticity for the material is E=25 GPa. Assume b=750 mm, L=1500 mm and t=20 mm. (10)
A downward load of Q = 33 kN is applied to rigid bar ABD as shown in the sketch. Axial member CDE is subjected to a downward load of P = 27 kN at joint E plus a force at joint D from the rigid bar. The axial member has an elastic modulus of E = 69 GPa and a cross-sectional area of A1 = A2 = 145 mm2. Assume that a = 390 mm, b = 220 mm, c = 630 mm, and d = 490 mm. Determine the vertical displacement of joint E. Determine the internal force and the change in length of section (1) of axial member CDE. Tension and elongation are positive. Compression is negative.Answer:F1 = kNδ1 = mm
Only accepted correct answer is 2.84. Please show solution. A steel plate 2.2 m x 1.4 m x 100 mm thick is to be hoisted by a steel cable sling as shown in the figure. Assume the steel weighs 77.3 kN/cu.m. Determine the vertical displacement of the steel plate when suspended if the sling cable is 55 sq.mm. in area.
The bar of negligible weight is supported by two springs, each having a stiffness k = 100 N/m. If the springs are originally unstretched, and the force is vertical as shown, determine the angle θ the bar makes with the horizontal, when the 30-N force is applied to the bar. Give your answer in degrees and to 3 significant digits.
A steel column 10 m long is fabricated from a cover plate and C section arranged as shown. Determinethe safe compressive load. (Figure below)adding a cover plate on the figure of the same size at the bottom, compute the centroidal moment of inertia about x and y axes
A beam with length L is FIXED at both ends. It is loaded with a concentrated force P at L/3 from the first support. (a) Draw the Loading Diagram. (b) Determine the deflection at midspan, EI is constant. (c) If the beam is made of steel, what is its elastic modulus? (d) If the beam has a length of 10 meters, cross section of 200x200mm, and force P is 10 kN, what is the deflection at midspan (in millimeters)?
For the given frame ABC in the figure below, if the 25KN/m uniform load is changed to 76KN/m and the 150KN horizontal load is changed to 214KN, Calculate the bending moment in KN-m at joint B? Express your answer in 2 decimal places. Include (-) sign if bending moment is negative.
Joists support a floor and transfer their load to beams at each end of each joist. Joists are 2 ft on center and 30 ft long. If w, the load on the floor, is uniformly distributed and is 30 lb/ft2, what is the load on one joist? If the maximum flexural stress S in a joist is given by S = M/Z, where M is the maximum bending moment (pound-foot) and Z is the section modulus (cubic inches), what is the stress in a joist that has a section modulus of 50 in.3 and is 30 ft long? Assume that the maximum bending moment for a simply loaded joist is given by M = wL2/8, If the joists are made of pine, which has an allowable bending stress of 9,300 lb/in.2, will it carry the load?
A cantilever beam shown in Figure B2 is applied with point load of 10KN and pointmoment of 7KNm. By using Macaulay method:Sebuah rasuk terjulur dikenakan beban tumpu 10KN dan moment lentur 7KNmseperti yang ditunjukkan dalam Rajah B2. Dengan menggunakan kaedah Macaulay:i) Derive the moment equation for the beam Terbitkan persamaan momen bagi rasuk
A vertical rectangular gate weighs 6000 lbs and is 10 ft tall and 8 ft wide (into the paper). The gate slides in vertical slots in the side of a reservoir containing water. The coefficient of friction between the slots and the gate is 0.03. Determine the minimum vertical force required to lift the gate when the water level is 4 ft above the top edge of the gate. [Answer in units of lbs.]
vertical bar is loaded with axial loadsat points B, C, and D, as shown in the figure. Thebar is made of steel with a modulus of elasticityE = 29,000 ksi. The bar has a cross-sectional area of8.24 in2. Calculate the displacements at points B, C,and D. Ignore the weight of the bar.
As shown in the figure below, determine the internal loadings at points A,B and. Consider the uniform weight of the whole structure which is 77 lbs per ft. FN= 87 OR 87X10 = 870