2. For the class B output stage of Figure 2, let Vcc = 6 V and R1 = 42. If the output is a sinusoidal with 4.5V peak amplitude, find; (a) The output power. (b) The average power drawn from each supply/ (c) The power efficiency obtained at this output voltage. (d) The maximum power that each transistor must be capable of dissipating safely.

2. For the class B output stage of Figure 2, let Vcc = 6 V and R1 = 42. If the output is a sinusoidal with 4.5V peak amplitude, find; (a) The output power. (b) The average power drawn from each supply/ (c) The power efficiency obtained at this output voltage. (d) The maximum power that each transistor must be capable of dissipating safely.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A Bipolar junction Transistor with curreat amplification factor being 100, Input Base current is 50μA. Collector voltage is 10 V and biasing voltage being +20 V. Find followings a. Collector current b. Resistance (R1) c. Collector voltage , Emitter voltage , Base Voltage & Collector-Emitter Voltage.
c. For the circuit shown in Figure, determine lc and VCB. Assume the transistor to be made of Silicon. Ic RE=1.6 kn Rc=1.1 kn EE=8 V Vcc= 20 v
circuits by using the small signal models of the transistor. Assume the Early voltage of the transistors are infinitely large. Calculate the small-signal input and output impedances of the following Vcc R1 R1 Rout VB RE Rin R2
Qa: A transistor dissipates 50W in an ambient temperature of 60°C, the thermal resistances are 0-0.5 °CW¹, 8ca-4 °CW. Determine the junction temperature without a heat sink. Determine the thermal resistance of the heat sink to avoid the junction temperature exceeding 180°C. )
9. Design a biased-transistor circuit using VBB = Vcc= 10 V for a Q-point of Ic = 5 mA and VCE 4 V. Assume pc = 100. The design involves finding RB, RC, and the minimum power rating of the transistor. (The actual power rating should be greater.) Sketch the circuit.
A) Find and draw the equivalent re circuit model. Calculate the voltage gain.
Q1. (a) Consider the amplifier circuit in Figure Q1(a). Given the following: RI = 100 k2 R2 = 56 kN Rc =2 k2 Vcc = +8 V Assume the transistor has B = 100 and VBE(on) = 0.7 V. You may neglect Early effect and use VT = 26 mV. (i) Draw the DC equivalent circuit, then determine Iç and VCE. Draw the AC equivalent circuit using re model. Based on this, determine the parameters Av, Rin and Rout. (ii) Vcc Rc R1 R2 C3 Vout C2 Ci Vin Figure Q1(a)
An NPN silicon transistor having a nominal ß of 100 is to be used in a CE configuration with Vcc= 15 V. The Q point is to be Ic = 4mA and VcE = 12V . Now design the circuit diagram.
Figure below shows a circuit for a pulse width modulator (PWM) amplifier. I. Describe how the circuit achieves low power dissipation 2. Describe with the aid of drawings the signal waveform shapes at points, A, B and C
Design the fixed bias circuit from the load line given in the figure below. Ic sat. =10mA IB=60UA Vcc= 20v VCE
QUESTION 1 By referring to Figure Q1, determine: a) The Q-point values of Ic and VCE. b) Draw the DC load line and plot the Q-point based on answer from Q1(a). c) The diode emitter resistance, re and draw re transistor model (AC equivalent circuu). d) The input impedance, Zi as seen from the input voltage. e) The output impedance, Z, as seen from output. f) The voltage gain, Av and the current gain, A¡.
3. Write down which transistor structure each curve characteristic belongs to in the figure. Ip -VGS -VGS +VGs (c) VGS (b) (a)