2. Forging. Based on 18.12 (7th ed.) A cylindrical work part has a starting height of 4 inches and a starting diameter of 2.5." In an open-dic forging process, the final height is 2.75". The cocfficient of friction is 0.10 and K = 25,000 psi and n = 0.22. Find the force required, in pounds, at the following heights: a) h= 3.992 in (the start of plastic deformation.) b) h = 3.375 in. (the halfway point) c) h = 2.75 in. (the final height)

2. Forging. Based on 18.12 (7th ed.) A cylindrical work part has a starting height of 4 inches and a starting diameter of 2.5." In an open-dic forging process, the final height is 2.75". The cocfficient of friction is 0.10 and K = 25,000 psi and n = 0.22. Find the force required, in pounds, at the following heights: a) h= 3.992 in (the start of plastic deformation.) b) h = 3.375 in. (the halfway point) c) h = 2.75 in. (the final height)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: ' Explain briefly the relationship between the load-stroke in open die forging as illustrated in the…

A: Considering the open die forging:-

Q: Q5- A single-pass rolling operation reduces a 15mm-thick plate to 12mm. The roll has a radius of…

A: GIVEN DATA INTIAL THICKNESS hi=15mm FINAL THICKNESS hf=12mm ROLL RADIUS R=400mm WE HAVE TO CALCULATE…

Q: 5) The first operation in closed die forging is Fullering Blocking Trimming Coining

A: Closed die forging is a plastic deformation process in which heated metal is forced to flow in a…

Q: 18.21 (USCS units) A direct extrusion operation is performed on a cylindrical billet with initial…

Q: Derive an expression for the reduction r in drawing as a function of drawing ratio DR.

A: 1. Reduction, r = D-d / D

Q: Question 8 8.1 Calculate the power required to roll an 8650 steel strip, 140 mm wide and 20 mm thick…

Q: Thickness of the plate is reduced from 40mm to 20mm by succesive cold rolling passes using identical…

Q: forming temperature condition. 8) In blanking operation, if the final blank diameter is 200 mm & the…

Q: Q11/which defect in sheets during rolling process appear if the roll bending?

A: As per given question We have to answer which defect in sheets during rolling process appear if the…

Q: Products produced by precision forging require Select one: O a. no additional finishing operations…

A: Introduction: Precision forging is defined as a flashless near net shape forging operation which…

Q: 19.3. A series of cold rolling operations are to be used to reduce the thickness of a plate from 50…

Q: Example8.2: An L-shaped structural section is direct extruded from an aluminum billet in which Lo =…

Q: A strip with a cross section 120 mm x 6 mm is being rolled with 20% reduction area, using rolls of…

Q: 9) In hydrostatic extrusion, the billet is smaller than the chamber is used, Why? 10) Earing is a…

A: Question - 9: During extrusion process, the billet is inserted into the extrusion chamber where…

Q: In a multi-pass operation, a round bar of 10 mm diameter and 100 mm length is reduced in…

Q: - A cup is to be drawn in a deep drawing operation. The height of the cup is 75 mm and its inside…

Q: Question 7 7.1 A component is designed to be hot forged in an impression die. The projected area of…

Q: )Give the reasons to use closed die forging.

A: Forgings minimize wasted material and are cost-effective, quick, and retain their durability under…

Q: Write a report and an explanation about Forging with the drawing

Q: ndrical workpiece is forged in an open die. The workpiece The height after forging is 15 mm. The…

Q: Question: 2 a. Distinguish between roll bending and roll forming. b. What are some of the simple…

A: This above all process are used for manufacturing purpose in mechanical industry.

Q: In blanking operation, if the final blank diameter is 200 mm & the clearance is 1.5 mm, then the Die…

A: Answer 8: In the blanking operation, the clearance is provided on the punch not on die so die and…

Q: (SI units) A series OI cold-rolling operations are to be used to reduce the thickness of a metal…

A: Find the minimum no of passes and draft of each pass

Q: 3) Which of the below statements is/are correct regarding deep drawing process? i. If the clearance…

A: In deep drawing process,the clearance is set to be 10% more than the sheet thickness. When the…

Q: "). A drawing operation is used to form a cylindrical cup with inside diameter = 75 mm, height = 55…

Q: 10)The maximum draft in a rolling operation is (R= radius of roll and p=coefficient of friction) is…

A: Rolling is a type of metal deformation that is commonly utilised in the metal forming process. It is…

Q: Describe with the aid of a neat sketches two forging processes and briefly discuss their relative…

A: Forging is a process of forming and shaping metals through the use of t hammering and pressing or…

Q: Write a Brief Application of Pure Rolling Bodies in The Mechanical Systems?

A: Pure rolling refers to the rolling process in which no slide is seen. Pure rolling is a motion…

Q: 13mm diameter rod is to be reduced to 11mm diameter by drawing in a single pass at a speed of…

Q: A drawing operation is used to form a cylindrical cup with inside diameter of 75 mm and height of 50…

A: Given, Inside diameter of cup = Dp = 75 mm Height of cup = h = 50 mm Starting blank diameter = Db =…

Q: A 200 mm wide and 42.0 mm thick plate made of low carbon steel is to be reduced in one pass in a…

A: Given: The width of the plate, b1 = 200 mm The thickness of plate initially, t1 = 42 mm The increase…

Q: solid cylindrical work piece is reduced in height by an open die forging process using flat dies on…

Q: Which of the following is true for extrusion process? A: In indirect extrusion, direction of the ram…

A: Metal forming is a manufacturing process in which the raw material is deformed plastically to obtain…

Q: Q2) Answer the following questions: 1. Is there any effect for the selection of the parting line in…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: the work metal has a flow curve defined by K=300MPa and n=0.2, and the coefficient of friction…

Q: What are the advantages of forging process?

A: Advantages of forging 1. Parts manufactured are stronger. 2. Forging offers high ductility. 3.…

Q: Q1: List and briefly Describe the different variations in rolling and forging.

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Describe the advantages of servo punch-presses for forging and stamping sheet metal parts.

A: Srevo Press:- The servo press is a press machine used for forging and stamping sheet metal parts by…

Q: 27(B). Distinguish the Open die and closed die forging process with its benefits and limitations.

Q: 7) Which of the following statement is/are 1 correct for extrusion process? i. In extrusion, block…

A: Extrusion is a process in which billet or bloom is forced through a opening which may be of any…

Q: 4) Make a summary of the types of defects found in sheet-metal forming processes, and include brief…

Q: forming proceɛɛ. 18) rolling mill type are associated with relatively small diameter rolls in…

A: Disclaimer from Bartleby: Since you have asked multiple question, we will solve the first three…

Q: Briefly describe the two types of forging dies.

Q: Q1- What are the main advantages of using the bulk deformation processes? Q2- Explain when the…

Q: 7) Sometimes Drawing crimps are used in deep drawing process for producing complex shapes. Why? 8)…

A: Deep drawing is basically a sheet metal process in which a sheet metal blank is transformed into…

Q: A deep drawing operation for a cup is performed in which the inside diameter = 60 mm %3D and the…

Q: 1) A cup-drawing operation is performed in which: The cup's inside diameter = 75 mm and its height =…

A: Given Datad=75mmh=50mmt=3mmRd=4mmσt=400MPa

Q: 7) In deep drawing of sheets, the values of limiting drawing ratio depends on percentage elongation…

A: As per given question deep drawing of sheets, limiting drawing ratio depends on

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

100%

2. Forging. Based on 18.12 (7th ed.) A cylindrical work part has a starting height of 4 inches and a
starting diameter of 2.5." In an open-dic forging process, the final height is 2.75". The cocfficient of
friction is 0.10 and K = 25,000 psi and n = 0.22. Find the force required, in pounds, at the following
heights:
a) h= 3.992 in (the start of plastic deformation.)
b) h = 3.375 in. (the halfway point)
c) h = 2.75 in. (the final height)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Step 7

Step 8

Trending now

This is a popular solution!

Step by step

Solved in 8 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Briefly describe the two types of forging dies.
19 In the open die forging ,a high precision is obtained. Select one: True False
27(B). Distinguish the Open die and closed die forging process with its benefits and limitations.
1. What process is flexible and is widely used for bending plates for applications such as boilers, cylindrical pressure vessels and various curved structural members? 2. Final velocity of strip in rolling is greater than its initial velocity? True or false?
Q26. Compare any ten major differences between Drawing process and Extrusion process
1. The friction in direct extrusion is ________ Indirect extrusion. a) Greater than. b) Equal to. c) Less than.2. The Temperature in hot forming process is ____. a) (0 to 0.4) Tm. b) (0.5 to 0.75) Tm. c) 0.9 Tm. d) 0.4 Tm. e) 0.8 Tm. f) (0.3 to 0.5) Tm. Where Tm is the melting temperature of the work piece.3. Maximum draft in rolling depends on _______. a) Coefficient of friction and roll radius. b) Thickness of plate. c) Smoothness of roll Surface. d) Roll rotational speed.e) Width of the plate. f) Length of the plate.4. In deep drawing process, the drawing ratio (DR) has a higher limit (value) of:- a) 6. b) 1. c) 4. d) 5. e) 7. f) 2. g) Zero.5. Spring Back is a phenomena usually associated with which of the following processes:-a) Extrusion. b) Forging. c) Bending. d) Wire drawing. e) Rolling. f) Sheet metal cutting. g) Deep Drawing.
The maximum possible draft in rolling which is the difference between initial and final thickness of the sheet metal, depends on A. Rolling force B. Roll radius C. Roll width D. Yield shear stress of the material
A solid cylinder of diameter 100 mm and height 50 mm is forged between two frictionless flat dies to a height of 25 mm. What is the percentage change in diameter?
1. Derive an expression for the reduction r in drawing as a function of drawing ratio DR.2. A cup is to be drawn in a deep drawing operation. The height of the cup is 75 mm and its insidediameter = 100 mm. The sheet-metal thickness = 2 mm. If the blank diameter = 225 mm, determine(a) drawing ratio, (b) reduction, and (c) thickness-to-diameter ratio. (d) Does the operation seem feasible?3. A drawing operation is used to form a cylindrical cup with inside diameter = 65 mm and height =50mm. The starting blank size = 140 mm and the stock thickness = 2.8mm. determine (a) drawing forceand (b) holding force, given that the tensile strength of the sheet metal (low-carbon steel) = 350 MPa andyield strength = 190 MPa. The die corner radius = 6 mm. Based on these data, is the operation feasible?
Question 1 solid cylindrical work piece is reduced in height by an open die forging process using flat dies on a mechanical press, powered by a 20 kW motor which operates at 35 strokes per minute with a stroke length of 160 mm. The work piece is 60 mm high and 100 mm in diameter and is to be reduced in height by 15%. The coefficient of friction during the operation is 0,18. Calculate the flow stress of work piece material if the press is set to operate at 90% of its maximum capacity.
Forging processes may be characterized by die work limitation. This categorization yields three basic types.
In a slab rolling operation, the maximum thickness reduction (del hmax) is given by del hmax = μ²R, where R is the radius of the roll and u is the coefficient of friction between the roll and the sheet. If µ = 0.1, find the maximum angle subtended by the deformation zone at the centre of the roll.