2. Four cylindrical rods are stretched. The force magnitudes, tho cross sectional arca, the initial lengths, and changes in length are shown in the table below. Rank the rods from largest to smallest Young's Modulus. ROD FORCE AREA Initial LENGTH LENGTH change 1 F A L AL 2 2F 2A L 2AL 3 F 2A 2L 2AL 4 2F A 2L AL

2. Four cylindrical rods are stretched. The force magnitudes, tho cross sectional arca, the initial lengths, and changes in length are shown in the table below. Rank the rods from largest to smallest Young's Modulus. ROD FORCE AREA Initial LENGTH LENGTH change 1 F A L AL 2 2F 2A L 2AL 3 F 2A 2L 2AL 4 2F A 2L AL

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In (Figure 1), F={500i−100j+700k}NF={500i−100j+700k}N. Part A: Determine the magnitude of the projection of the force FF acting along the cable BABA. Express your answer to three significant figures and include the appropriate units.
The cross section of the rod in the picture is a circle and the elastic modulus of the material is 200 GPa (material S235JRG2). The rod is pulled with a force of F = 5250 N. Determine the minimum value of the rod diameter d when the rod length is L = 5250 mm and a length change of ΔL = 4.0 mm is allowed for the rod. Also determine the safety with respect to the rod. Use units in calculations [N, mm] Enter the answer to one decimal place. Do not round the invoices in the intermediate stages, but only the final answer!
The wires AB and AC are made of steel, and wire AD is made of copper. Before the 150-lb force is applied, AB and AC are each 60 in. long and AD is 40 in. long. If the temperature is increased by 80F, determine the force in each wire needed to support the load. Each wire has a cross-sectionalarea of 0.0123 in2. Take Est = 29(10 3) ksi, Ecu = 17(10 3) ksi, fast = 8(10 6)>F, acu = 9.60(10 -6)>F.
Show complete solutions and figures The diameters of the two cylinders A and B in the figure shown are 80 mm and 750 mm, respectively. The face of the piston is 1.2 m above the face of the weight platform. The space in between the piston and the weight is filled with oil (s.g.=0.80). If F=75 N, Determine the following: the value of Wrequired to maintain equilibrium. a) 38.6 N b) 86.3 N c) 63.8N d) 83.6 N e) None
Datos: F1(KN)=5 F2(KN)=20 F3(KN)=10 L1(m)=4 H(m)=-5 I add the picture of the question
The process of splitting a force into its component forces is called ____________ Select one: Resolution of forces Splitting of forces compounding of forces Composition of forces
In determining the net cross sectional area of a structural steel tension member, the diameter of a rivet hole, in relation to the diameter of the rivet,is assumed to be A. 3/16 in. larger B. 1/8 in. larger C. 1/16 in larger D. the same size
A wire made from Material Y has a 3 millimeter [mm] diameter and is 1.25 feet [ft] long. A stress is created by applying a force over the circular cross-sectional area of the wire, where the circular area is given by: A = π r2. This stress causes a strain of 0.045 [mmmm]. Determine the force used to stretch the wire, in units of newtons [N].
The pressure in a cast-iron water pipe is 180 psi. If the inside diameter of the pipe is 15 in. and the allowable unit stress in tension is 2000 psi, what should be the thickness of a shell of the pipe, expressed as a multiple of 1/8 in. A. 3/4 in. B. 5/8 in. C. 1/2 in. D. 3/8 in.
A man on the wire singing "Man on a Wire" while practicing for his circus show has reached the center of the rope, creating a dip on the center angled at 63.2 degrees. If the mass of the man is 49.55 kg and the tension force that can be handled by the wire is 449.77N, would the wire break? Show the tension caused by the man hanging on the wire.
A metal cylinder hangs from the ceiling through three cables attached as shown. If the tension in cable AD is 4.3 kN, what would be the (a) tension on cables AB and AC (b) weight of the cylinder Answer: T_AB=4.1667kN ; T_AC= 3.8250kN; W=9.71kN Kindky answer it with complete solution and with this format: Given Equation Solution
Solid steel wire (2 meters) contains a musical instrument (0.3 mm). When the wire is under tension (90N), how does its length change?