2. The clamp of the given figure is used to hold a cover in place. The screw of the clamp has a single thread with a mean radius of 0.20 in and a pitch of 0.08 in. The coefficient of friction is 0.45, and the required clamping force is 100 lb. (a) Determine the twisting moment to tighten the clamp and (b) determine the twisting moment to loosen the clamp. 0/45 ×0/20 = 0/09 ING 0745 X 07 08th = 0,036/N x 0,20 + 809 (4²1036=0 P

2. The clamp of the given figure is used to hold a cover in place. The screw of the clamp has a single thread with a mean radius of 0.20 in and a pitch of 0.08 in. The coefficient of friction is 0.45, and the required clamping force is 100 lb. (a) Determine the twisting moment to tighten the clamp and (b) determine the twisting moment to loosen the clamp. 0/45 ×0/20 = 0/09 ING 0745 X 07 08th = 0,036/N x 0,20 + 809 (4²1036=0 P

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.19P: -19 The mechanical assembly shown in the figure consists of an aluminum tube, a rigid end plate, and...

See similar textbooks

Similar questions

-19 The mechanical assembly shown in the figure consists of an aluminum tube, a rigid end plate, and two steel cables. The slack is removed from the cables by rotating the turnbuckles until the assembly is snug but with no initial stresses. Afterward, the turnbuckles are tightened by 1.5 turns. Calculate the forces in the tube and the cables and determine the shortening of the tube. As= 0.85 in2 for each cable, AA= 4.5 in2, L = 20 in., Es= 29,000 ksi, EA= 10,600 ksi, and p = 1/16 in
Page 428. Sample Problem 6.1.Solve this problem completely;but replace theapplied point-forceon the rightfrom 1.5 kN to 2 kN.Let the one on the left remain unchanged.At the same time, instead of computing the averageshearing stress in each joint at the provided sectionn-n, please find the average shearing stress in each jointfortheworst section of the beamwherever it is(and state/show where it is), not necessarily at the providedlocation ofsectionn-n.Keep in mind that this change will result in many other changes across the board.Discuss all practicalissues in your findings.For example, where is the system likelyto fail in terms of the glued parts, and why?
In the figure below the clamping force on the pipe is (331.7 lb), knowing that a single threaded screw Acme with major diameter (1 in) is used with coefficient of friction (0.2135). If booth screw and nut are made from 1030 - hot rolled Carbon Steel. Determine: 1- The tightening and loosening torques. 2- Thread screw and nut shear safety factors in case of double threads are in engagement. 3.3 in 2 7.2 in 32 3 in hinge
2. A 30-mm bolt with an initial tension of 35 kN is subjected to several types of stresses during initial tightening or due to screwing up forces. If the bolt has a core diameter of 25.7 mm and considering 5 threads are already engaged with the nut, calculate the shear stress across the thread and the crushing stress between the threads. Assume 3.5 mm as the width of the thread section at the root.
In a bolted joint two members are connected with an axial tightening force of 2200 N. If the bolt used has metric threads of 4 mm pitch, the torque required for achieving the tightening force is
A solid and a hollow shaft, connected by a coupling, transmit power. The outside diameters of the shafts are the same and the inside diameter of the hollow shaft is 75 % of its outside diameter. The solid shaft is three times as long as the hollow shaft. Take the modulus of rigidity for both shafts as 80 GPa. (a) If the angle of twist for the solid shaft is 1°, find the angle of twist for the hollow shaft. (b) If the maximum shear stress in the solid shaft is 30 MPa, find the maximum stress in the hollow shaft.
A flange coupling having six bolts on a pitch circle radius of 300 mm connects two hollow shafts with an outside diameter of 400 mm. The diameter of each bolt is 65 mm and the limiting shear stresses in the bolts are to be the same as that for the shafts, (a) Calculate the inside diameters of the shafts, (b) Take G as 80 GPa and calculate the angle of twist in degrees over a shaft length of 5 m for a working stress of 60 MPa.
In the system shown in the figure, 2 sheets are connected to each other with the help of rivets with equal diameters and are forced by the force F. Of the 16 rivet slots shown in the figure, only the rivets shown in the brackets were used, and holes were drilled only for the specified rivets (16 holes on the sheet are NOT available. Only A4, B1, C1, D3 are holes.) i) Determine the center of rotation of the rivets. ii) Determine the rivet diameter required for the system to be safe.
Two solid shafts, 50 mm in diameter, are connected by a flange coupling with six bolts and a pitch circle diameter of 95 mm. If the maximum shear stress in the shaft due to a torque is to be the same as the shear stress in the bolts, calculate a suitable bolt diameter. If the maximum working shear stress is limited to 55 MPa, what maximum power will be transmitted by the coupling at 700 r/min?
A bevel gear is attached to a shaft supported by self-aligning bearings at A and B and is driven by a motor. The axial force, radial force, and tangential force are known. Assume the weight of the gear and shaft is negligible and that the bearing at A takes all the thrust load A) Draw (to scale) axial load, shaft torque, shear force(x-y and x-z), and bending moment(x-y and x-z)diagrams for the shaft B)Determine the values of axial load and torque along the shaft
(6) A double square-threaded power screw transmits 1,800in-lb of torque and raises a machine head; the head is guided by linear slides with anti-friction bearings, and thus no appreciable friction is involved. If the coefficient of friction for the threads is 0.1, find: (a) the load that can be raised if the screw has 2 threads/in and an outside diameter of 2½in; (b) if a 4000-lb load is to be lowered, what torque must the screw transmit? (c) if the power screw of rotates 10 rpm, what is the linear speed of the driven head in feet per minute?
In a tensile test on a steel tube of external diameter 18 mm and internal diameter 12 mm, an axial pull of 2 kN produces stretch of 6.72x 10^-3 mm in a length of 100 mm and a lateral contraction of 3.62x10^-4mm in outer diameter. Calculate the values of three modulus and Poisson's ratio of the material