2. The power flow on the transmission line in Figure 3 is 10 pu and the voltage at both busbars is 1.0 pu. The system frequency is 50 Hz. The power flow is estimated using the phase difference between busbars 1 and 2, that is using o1 – o2. The measurement of the phase angle p1 has a time stamp error of 0.1 ms and that of the phase angle o2 is 0.2ms. Find the error in the estimated power flow.

2. The power flow on the transmission line in Figure 3 is 10 pu and the voltage at both busbars is 1.0 pu. The system frequency is 50 Hz. The power flow is estimated using the phase difference between busbars 1 and 2, that is using o1 – o2. The measurement of the phase angle p1 has a time stamp error of 0.1 ms and that of the phase angle o2 is 0.2ms. Find the error in the estimated power flow.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.60P: PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06...

See similar textbooks

Similar questions

While the instantaneous electric power delivered by a single-phase generator under balanced steady-state conditions is a function of time havi ng two components of a constant and a double-frequency sinusoid, the total instantaneous electric power delivered by a three-phase generator under balanced steady-state conditions is a constant. (a) True (b) False
Figure 3.32 shows the oneline diagram of a three-phase power system. By selecting a common base of 100 MVA and 22 kV on the generator side, draw an impedance diagram showing all impedances including the load impedance in per-unit. The data are given a follows: G:90MVA22kVx=0.18perunitT1:50MVA22/220kVx=0.10perunitT2:40MVA220/11kVx=0.06perunitT3:40MVA22/110kVx=0.064perunitT4:40MVA110/11kVx=0.08perunitM:66.5MVA10.45kVx=0.185perunit Lines I and 2 have series reactances of 48.4 and 65.43, respectively. At bus 4, the three-phase load absorbs 57 MVA at 10.45 kV and 0.6 power factor lagging.
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
Determine the bus admittance matrix (Ybus) for the three-phase power system shown in Figure 6.23 with input data given in Table 6.11 and partial results in Table 6.12. Assume a three-phase 100 MVA per unit base. TABLE 6.11 Bus input data for Problem 6.20 TABLE 6.12 Partially Completed Bus Admittance Matrix (Ybus) for Problem 6.30
With generator conyention, where the current leaves the positive terminal of the circuit element, if P is positive then positive real power is delivered. (a) False (b) True
A balanced three-phase load is connected to a 4.16-kV, three-phase, fourwire, grounded-wye dedicated distribution feeder. The load can be mode led by an impedance of ZL=(4.7+j9)/phase, wye-connected. The impedance of the phase conductors is (0.3+j1). Determine the following by using the phase A to neutral voltage as a reference and assume positive phase sequence: (a) Line currents for phases A, B, and C. (b) Line-to-neutral voltages for all three phases at the load. (c) Apparent. active, and reactive power dissipated per phase, and for all three phases in the load. (d) Active power losses per phase and for all three phases in the phase conductors.
Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
Shown are two buses connected via a transmission line. Connected to Bus 1 is a generator(modelled as a voltage source V1), and to Bus 2 is a generator( with Voltage V2) and a load. The line impedance Z = R + jX is not known. Three-phase load is forecasted as 100MW + 60MVar. Generator at Bus 2 is scheduled to deliver 40MW and its excitation is adjusted for the machine to deliver 55 MVar. Voltage at Bus 1 is 241 KV angle 10 deg, while voltage at bus is 230 kV; use V2 as the reference for all angles. 1. What is the current (RMS) in amperes drawn by the load connected to Bus 2? 2. How much real power (in MW) is delivered by the generator connected to Bus 1? 3. What is the total real power loss along the line, in percent of the load? 4. What is the X/R Ratio of the line impedance?
A 60 Hz, three-phase transmission line is 100 miles long. It has a total seriesimpedance of {35 + j120) n and a shunt admittance of j930 μsiemen. It delivers40 MW at 220 kV with 90% lagging power factor. Find the voltage at the sendingend by:(a) short line approximation(b) the nominal rr approximation(c) the nominal T approximationAlso determine the voltage regulation for the given line and the power loss.Assume the sending end voltage remains constant. Expected Answer: (a) 237.67 kV, 1.4284 MW, 8.03%; (b) 225.8 kV, 1.1642 MW, 8.67% (c) 225.10 kV, 1.5095 MW, 8.35% Pls. Provide Full Solution for thumbs up
The annual load duration curve of a power supply system may be considered as straight line from 40 MW to 8 MW. The load factor of the system is ?
Refer to Figure 1. Using its equivalent reactance diagram, what is the total impedance of the system up to the fault point at the end of the receiving line (in per unit)? Below are the parameters: G1 : 9 MVA, 13 kV, j0.11 p.u. G2 : 8 MVA, 13 kV, j0.06 p.u. T1 : 9 MVA, 13/69 kV, j0.042 p.u. TL : 262 km, 0.031 ohm per km, 0.3 ohm per km, operates at 69 Base values are that of G1. Round your answer to 2 decimal places. what is the fault MVA of the system when a three-phase fault occurs at the receiving end?
Question-2) The parameters of a three-phase transmission line are given as Z = (12.84 + j72, 76)Ω and y = j5, 83x10^-4 mho. At the end of the line, a power of 55 MVA with a power factor of 0.8 is drawn under 132 kV voltage. Accordingly, calculate the line head voltage, active and reactive power values per line, and voltage regulation of the line using the nominal π circuit.7-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the line head voltage (phase-phase voltage) and enter it in the box below. (The value will be entered in kiloVolts. Only the amplitude value of the voltage will be entered. The phase value will NOT be entered!!! Two digits after the comma will be sufficient. )8-) Since 55 MVA power is drawn from the end of the line under the conditions mentioned above, calculate the active power value per line and enter it in the box below. (The value will be entered in MegaWatt. It will be sufficient to take two digits after…