2.1 A uniformly distributed load ofintensity g is applied through a circular area of radius a on the surface of an incompressible (v -0.5) homogeneous half-space with an elastic modu- lus E, as shown in Figure P2.1. In terms of g, a, and E, determine the vertical displacement, three principal stresses, and three principal strains at a point 2a below the surface under the edge (r = a) of the loaded area. [Answer: - 0.58 qalE, -0.221q.0 0.011q, os = 0.004q, e; = 0.214q/E, v; = -0.102q/E, es - -0.112q/E]| 2a v05 2a ww7 100, ? FIGURE P2.1

2.1 A uniformly distributed load ofintensity g is applied through a circular area of radius a on the surface of an incompressible (v -0.5) homogeneous half-space with an elastic modu- lus E, as shown in Figure P2.1. In terms of g, a, and E, determine the vertical displacement, three principal stresses, and three principal strains at a point 2a below the surface under the edge (r = a) of the loaded area. [Answer: - 0.58 qalE, -0.221q.0 0.011q, os = 0.004q, e; = 0.214q/E, v; = -0.102q/E, es - -0.112q/E]| 2a v05 2a ww7 100, ? FIGURE P2.1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane stress condition determine: -all 3 principle stresses, the max in plane stress, average noemal stress and the absolut max shear stress. - Show the principle stress, the max inplane shear stress and the average normal stress on an appropriate schematic
The principal strains in a plane, measured experimentally at a point on the aluminum fuselage of a jet aircraft, is ε1 = 117x 10^6, and ε2 = 167 x 10^6. If this is a case of plane stress, determine the associated principal stresses at thepoint in the same plane.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sx = 12 ksi, Sy = 17 ksi, and Sxy = 18 ksi.(a) Draw Mohr’s circle for this state of stress.(b) Determine the principal stresses (σp1>σp2σp1>σp2) and the maximum in-plane shear stress τmaxτmax acting at the point.(c) Find the smallest rotation angle θpθp (counterclockwise is positive, clockwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16)
At a point in a strained material, the intensities of normal stresses on two planes at right angles to each other are 35 N/mm2 and 20 N/ mm2 both tensile. They are accompanied by shear stress of 15 N/ mm2. Find the principal planes and principal stresses. Find also maximum shear stress.
A closed cylindrical vessel made of steel plate 10 mm thick, with a plain ends carries fluid under a pressure of 20 N/mm², The diameter of cylinder is 400 mm and the length is 1500 mm. The steel plate young's modulus is 180000 N/mm² with a poisons ratio of .3 ,Determine the following a) The hoop stress in the cylinder wall b) The diameter change c) The change in Length
mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
At a point on the free surface of a machine part (E = 214 GPa, G = 83 GPa), the state of the stress is illustrated in the figure below. For the given plane stress condition determine: the average normal stress and absolute max shear stress
1. A thin-walled cylinder with a diameter of 20 cm and a wall thickness of 2 mm is filled with gas at a pressure of 2 MPa. Calculate the longitudinal stress, and circumferential stress in the cylinder wall.
Several forces (F = 200 N and P = 150 N) are applied to the pipe assembly as shown in Figure Q1(b). Knowing that the inner and outer diameters of the pipe are equal to 40 mm and 45 mm, respectively, determine: a) the principal planes and the principal stresses at point H located at the top of the outside surface of the pipe and sketch the orientation of the element, b) the maximum in-plane shearing stress at the same point and sketch the orientation of the element c) the absolute maximum shearing stress at the same point
Question 3 - Strain Energy A brass tube with an outside diameter of 20 mm and 4 mm wall thickness is 80 mm long.It is joined to the end of a solid brass rod with a diameter of 20 mm and 120 mm long toform a compound assembly. This assembly is subjected to tension due to a mass of 150kg moving at a speed of 0.4 m/s.3.1. Determine the stresses induced in the rod and the tube respectively.3.2. Determine the change in length of each part, as well as the total change in length ofthe assembly.3.3 Determine the equivalent impact load (in kg) required to have the same effect(produce the same amount of energy) if falls freely from a height of 10 cm onto acollar attached to the bottom of the assembly if the assembly is vertically attachedat its top.3.4 How much strain energy is absorbed by each section of the assembly?(For brass: E = 100 GPa and α = 18×10-6/ 0C)
Figure Q2 shows few loadings applied on bar ABD. Suppose the diameter of the bar is 60mm,and knowing that P1 = 13kNm, P2 = 5 kNm and P3 = 12 kNm. Values A,B,C are given in TableQ2. (a) Find the following stresses at point H. (i) Normal stress due to P1 (ii) Bending stress and shear stress due to P2 (iii) Normal stress due to P (b) Determine the state of plane stress at point H and show it on the element. (c ) Using Mohr’s circle, determine the principal stresses at point H and show the result onthe element.
A bar of circular cross section is subjected to point loads of P1, P2, P3 and P4 as shown here. Find the magnitude of the force P3 necessary for the equilibrium, if P1= 110 kN, P2 = 210 kN & P4 = 160 kN. Also, determine the stresses in each section & the net change in the length of steel bar. where d1=50mm, L1=34 cm, d2 = 35mm, L2=35 cm, d3=50 mm & L3 =32 cm. Take E = 167 GPa. The force P3 to make it to equilibrium in kN is The Stress in section 1 in N/mm2 is The Compressive Stress in section 2 in N/mm2 is The stress in section 3 in N/mm2 is The total change in length in x10-3 mm is