2.19 The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the largest vertical load P that can be applied at C if the stress in the steel rod is limited to 35 ksi and the vertical movement of end C must not exceed 0.12 in. Ne- glect the weights of the members. L=4 ft A= 0.5 in.2 E= 29 x10 psi B 2 ft- 3 ft FIG P2 19

2.19 The rigid bar ABC is supported by a pin at A and a steel rod at B. Determine the largest vertical load P that can be applied at C if the stress in the steel rod is limited to 35 ksi and the vertical movement of end C must not exceed 0.12 in. Ne- glect the weights of the members. L=4 ft A= 0.5 in.2 E= 29 x10 psi B 2 ft- 3 ft FIG P2 19

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 1021-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 472 mm2. Find the magnitude of P (in N) that can be safely applied to the bar if the stresses in AC and BD are limited to 110 MPa and 51 MPa, respectively. Express your answer in two decimal places.
A 50-kN force is subjected to a lap joint fastened by three 20-mm diameter rivets.(a) the shearing stress in each rivet.(b) the bearing stress in each plate.(c) the maximum average tensile stress in each plate. Assume that the axial load P is distributed equally amongthe three rivets. equally among the three rivets.
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 10 mm2. The cross-sectional area of rod (2) is 19 mm2. For a uniformly distributed load of w = 3.5 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 4.55 m.
A 5-kN tensile load is applied to a test coupon made from 1.6-mm flat steel plate (E = 200 GPa, v = 0.30). Determine the change in volume of the 50-mm gage lenght segment AB by computing the dilatation of the material. Determine the change in volume of the 50-mm gage length segment AB by subtracting the original volume of portion AB from its final volume.
The rigid bar ABC is suspended from three wires of the same material. The cross-sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P.
A 150mm x 30mm x 250mm central wooden block is glued between cantilevered brackets 200mm x 50mm each as shown. If the Shear Stress of the glued joint can NOT exceed 4N/mm2, find the Vertical load that can be applied on the central plank.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 107 MPa, determine the minimum diameter (in mm rounded to the nearest hundredths) required for rod 1 and rod 2. Assume P = 80 kN and Q = 140 kN.
Determine the largest weight W in N that can be supported by two wires shown in the figure.The stress in either wire is not to exceed 261 Mpa. The cross-sectional areas of wires AB and ACare 258 mm^2 and 320mm^2 respectively.
An aluminum [E = 10000 ksi] control rod with a circular cross section must not stretch more than 0.21 in. when the tension in the rod is 2230 lb. If the maximum allowable normal stress in the rod is 11.2 ksi, determine:(a) the smallest diameter d that can be used for the rod.(b) the corresponding maximum length L of the rod.
A 5-kN tensile load is applied to a test coupon made from 1.6-mm flat steel plate (E = 200 GPa, v = 0.30). Determine the change in volume of the 50-mm gage length segment AB by computing the dilatation of the material.
The homogeneous bar ABCD shown in figure below is supported by acable that runs from A to B around the smooth peg at E, a vertical cableat C, and a smooth inclined surface at D. Determine the mass of theheaviest bar that can be supported if the stress in each cable is limitedto 100 MPa. The area of the cable AB is 250 mm2 and that of the cableat C is 300 mm2.
Two members AB and AC are made of material with E= 138 Gpa and each member has cross sectional area of A= 346 mm2. The members are used to support bar BC. If P=1917 N, L1= 242 mm , L2= 373 mm and L3= 459 mm . Answer the following questions. The tension in member AB? The tension in member CD? The elongation in member AB? The elongation in member CD? Vertical displacement of point E?