Answered: Given a system as shown in the…

Name: Given a system as shown in the following figure. Calculate the water
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Given a system as shown in the following figure. Calculate the water level differencebetween two tanks.PVAC 7.35 psiP. 0.5 atAZ=2 m1= 15 md 30 mmΣ-3. λ0.05V =1 m/hH,O

Engineering

Mechanical Engineering

Given a system as shown in the following figure. Calculate the water level difference between two tanks. PVAC 7.35 psi P. 0.5 at AZ 2 m 1= 15 m d 30 mm Σ3, λ0.05 V =1 m/h H,O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pipe with unequal ends is used to transport a fluid. The pipe diameter at the larger end is 0.67 cm and the other end is 0.29 cm. The larger and smaller ends are located 9 m and 3 m, respectively, from the datum line. If the flow at the 9 m datum line is 1.48 m/s and the pressure is 5156 kN/m2, compute for the pressure, in kPa, at the smaller end. Express your answer in 3 decimal places.
Question : SAE 30 oil at 20°C flows in the 3.5-cm-diameter pipe, which slopes at 37°. For the pressure measurements shown, determine Part (a) whether the flow is up or down and Part (b) the flow rate in m3/h. Neglect minor losses. Directions - Solve carefully, Write Clear, Label as Part (A) and (B) Circle Final answer(s) Hint : flows in the 3.5-cm-diameter pipe, *** USE IMAGE BELOW Pb = 190kPa, Pa = 550kPa, 25m, etc
Water ( density 1000kg/m3) flows downward naturally through a vertical pipeline of diameter D=25 cm and length L= 100 m . Determine the pressure gradient causing flow ( USE π = 3 ; g = 10 m2/s ) ANSWER: 10 kPa/m (Although I wrote this is the answer under the question in some of the questions I posted before. Different answers were found from the answer. The exact answer to this question is 10kPa / m.)
A 25cm circular pipe carries 0.16m3 /sec of water under a pressure of 200Pa. The pipe islaid at an elevation of 10.71m above the mean sea level (MSL) of Ibadan. What is theenergy head measured with respect to the MSL? If = 9810N/m3 (9.81KN/m3).
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
Determine the size of a galvanised iron pipe needed to transmit water a distance of 180 m at 0.085 m> /s with a loss of head of 9 m. (Take kinematic viscosity of water n=1.14 x 10°m? /s, and the average surface roughness for galvanised iron = 0.15 mm).
Using a flexible drinking straw and a ruler, explain how you would measure the water flow velocity in a river.
Define net positive suction head and required net positive suction head, and explain how these two quantities are used to ensure that cavitation does not occur in a pump.
A pipe, 12 inch in diameter at A, discharges 4.0 cfs of heavy fuel oil (sp gr = 0.899) into the air at B, where the diameter is 6 inch. If B is 12 ft above A and the frictional loss between the two points is equivalent to 3.0 lb per sq in, determine the pressure at A in pounds per square inch.
Apply Bernoulli equation in solving the problem: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127 cm manometer filled with mercury is used to measure the pressure difference across the venturi meter. If the manometer reads 101.6 cm when 15 °C water is flowing through the pipe, what is the flow rate of water (m3/min)? Assume that the venturi meter coefficient of discharge equals 0.98.
A ship of 8500 tons displacement has a double bottom tank 11 m wide divided longitudinally in half equally, having a free surface of fuel oil density 0.85 t/m3 . If the virtual loss in metacentric height due to slack fuel oil tank is 5 cm. find the length of the tank.
Show complete solution with diagram: A 3.81-cm diameter venturi meter is installed in a pipe with an internal diameter of 10.23 cm. A 127 cm manometer filled with mercury is used to measure the pressure difference across the venturi meter. If the manometer reads 101.6 cm when 15 °C water is flowing through the pipe, what is the flow rate of water (m3/min)? Assume that the venturi meter coefficient of discharge equals 0.98.