2.3 Show all Calculations 2.3) The one side of a coaxial cable is connected to a signal generator. On the otherside of the coaxial cable, the output impedance was measured as R1 2. The cable isthen connected to a horn antenna, that has an impedance of R2 2. Calculate themismatch loss in dB and show all the calculations.R1 = 46R2 = 82

Given information, Coaxial cable output impedance is R1=46 Ω. Horn antenna resistance is R2=82 Ω. We…

2.3) The one side of a coaxial cable is connected to a signal generator. On the other side of the coaxial cable, the output impedance was measured as R1 22. The cable is then connected to a horn antenna, that has an impedance of R2 2. Calculate the mismatch loss in dB and show all the calculations. R1 = 46 R2 = 82

2.3) The one side of a coaxial cable is connected to a signal generator. On the other side of the coaxial cable, the output impedance was measured as R1 22. The cable is then connected to a horn antenna, that has an impedance of R2 2. Calculate the mismatch loss in dB and show all the calculations. R1 = 46 R2 = 82

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem ECSQ

See similar textbooks

Similar questions

Is the input impedance of the amplifier circuit shown in Figure 21 capacitive or inductive? Justify the frequency behavior of Zin with frequency.
21. FM can be produced using a phase modulator.Group of answer choices True False 22. In PM, frequency deviation is directly proportional to the amplitude of the modulating signal.Group of answer choices True False 23. The lowest frequency deviation in the carrier occurs during the zero-crossing points of the modulating signal.Group of answer choices True False 24. Modifying the frequency of the carrier produces frequency modulation.Group of answer choices True False 25. FM produced by a phase modulator is called indirect FM.Group of answer choices True False 26. The modulating signal for stereophonic subcarrier shall be equal to the sum of the left and right signals.Group of answer choices True False 27. The amplitude of the modulating signal determines the frequency deviation in the carrier.Group of answer choices True False 28. Phase shift is indirectly proportional to the amplitude of the modulating signal.Group of answer choices True False 29. Phase modulators produce a phase…
A transmitter has a directional antenna with a gain of 4 dB. The frequency is 72 MHz. The power into the antenna is 2 W. The receiver uses a one-quarter wavelength ground plane. The distance between the transmitting and receiving antennas is 3 mi. What is the power at the receiver? What is the receiver input voltage with a 50-V input impedance?
For V = ± 6Volt and C1 = 0.001 µF in the Phase Locked Loop (PLL) circuit given belowa) Find the free running frequency (f0)?b) Find the deadlock range? Calculate the lowest and high frequency for locking?c) Find the capture range?
i) Which type of compensator is used for feeding reactive power at the receiving end? Draw its block diagram. (ii) What is lag-lead compensator? Draw its circuit diagram and derive the expression for the transfer function of lag-lead compensator.
A 50 ohms transmission line of length L=λ/2 in Figure Q.1 is to be used in RF testing. Determine the input impedance and VSWR when the line is terminated by: (i) an open-circuit termination (ii) a short-circuit termination (iii) 50 ohms load termination.
24. Modifying the frequency of the carrier produces frequency modulation.Group of answer choices True False 25. FM produced by a phase modulator is called indirect FM.Group of answer choices True False 26. The modulating signal for stereophonic subcarrier shall be equal to the sum of the left and right signals.Group of answer choices True False 27. The amplitude of the modulating signal determines the frequency deviation in the carrier.Group of answer choices True False
What is the bandwidth of the system?
The noise coefficient of a microwave receiver front section is desired to be measured by the Y-factor method. Using a noise source with an extreme power rating (ENR) of 23 dB and a liquid nitrogen cold load (77 °K), the Y-factor ratio is measured to be 14.83dB. Find the noise coefficient of the receiver
Which of these filters are stable,which of these are unstable and why?
763. (NEW) This is about two points, (x1,y1) and (x2,y2), on a straight line whose slope is given in dB/decade. The x-axis is log and the y-axis is linear. Find x2 given: y1=17 dB, x1=13, y2=21 dB, slope=48 dB/decade.
Accordingly; a) What is the undercut frequency of the circuit? b) What is the upper cutoff frequency of the circuit?