2.attention to the piping system shown in the figure below. Pipes 1, 2, and 3 are installed in parallel to connect reservoirs A and B. It is known that the discharge in the main pipe is 500 L/s. Determine Q1, Q2, and Q3! Use the data related to the piping system as listed below. •D1 = 350 mm, L1 = 300 mm, f1 = 0.014 • D2 = 450 mm, L2 = 200 mm, f1 = 0.0145 • D3 = 250 mm, L3 = 350 mm, f1 = 0.017 %3D A

2.attention to the piping system shown in the figure below. Pipes 1, 2, and 3 are installed in parallel to connect reservoirs A and B. It is known that the discharge in the main pipe is 500 L/s. Determine Q1, Q2, and Q3! Use the data related to the piping system as listed below. •D1 = 350 mm, L1 = 300 mm, f1 = 0.014 • D2 = 450 mm, L2 = 200 mm, f1 = 0.0145 • D3 = 250 mm, L3 = 350 mm, f1 = 0.017 %3D A

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter26: Applications Of Refrigeration Systems

Section: Chapter Questions

Problem 6RQ: When the compressors are located in the equipment room, the piping is routed A. in floor chases or...

See similar textbooks

Similar questions

a) Two pipes have a length ? each. One of them has a diameter D, and the other a diameter d.if the pipes are arranged in parallel, the loss of head when a total quantity of water Q flows through them is h, but, if the pipes are arranged in series and the same quantity Q flows through them, the loss of head is H. If ?=?/2, find the ratio of H to h, neglecting secondary losses and assuming the pipe coefficient f has a constant value. b) A pipeline of 0.6m diameter is 1.5km long.To increase the discharge, another line of the same diameter is introduced parallel to the first in the second half of the length.Neglecting minor losses, find the increase in discharge if 4f = 0.04. The head at inlet is 300mm. c) Determine the difference in the elevations between the water surfaces in the two tanks which are connected by a horizontal pipe of diameter 300 mm and a length of 400 mm. The rate of flow of water through the pipe is 300 litres/s. Consider all losses and takef=0.008. d) Water at 20°C is…
choose the correct answer Water flows horizontally from section 1 to section 2. If the area of section 1was 3 times area of section 2 then the velocity of section 1(v1) will be: * a) v1= v2 b) v1=1/2 v2 c) v1= 1/3 v2 d) v1= 1/4 v2 E)none of all above
For the pipe system shown. Assume n = 0.013 for all pipes. Neglect minor losses. 1. Compute the head loss from A to B in terms of Q. a. 0.056Q2 b. 0.029Q2 c. 0.016Q2 d. 0.096Q2 2. Assuming Q = 12 cfs, compute the head loss of pipe CD. a. 15.78 ft b. 13.02 ft c. 18.56 ft d. 24.56 ft 3. Assuming Q = 12 cfs, compute the total head loss from A to D. a. 47.786 ft b. 56.673 ft c. 89.451 ft d. 32.562 ft
A pipe AB carries water and tapers uniformly from a diameter of 4" at A to 8" at B over a length of 6 ft. Pressyre gauges are installed at A, B and also at C, the midpoint of AB. If the pipe centerline slopes upwards from A to B at an angle of 30° and the pressures recorded at A and B are 2.0 and 2.3 bar, respectively. (1 bar = 14.5 psi) Illustrate the problem before answering the following questions: (a)determine the flow, in ft^3/s through the pipe at C neglecting all lossess. (1 bar = 14.5 psi) (b)determine the pressure in bars, recorded at C neglecting all losses.
The water in a 750 cubic meter treatment water tank is discharged under the influence of gravity to a point 15 m below the tank bottom through a 150 mm diameter commercial steel pipe of 1000 m. If you think that it is a continuous system with a constant water height of 3.5 in the tank, what will be the discharge rate in cubic meters / hour.
Water flows upwards in a vertical pipeline of gradually varying section from point 1 to point 2, which is 1.5m above point 1, at the rate of 0.9m^3/s. At section 1 the pipe diameter is 0.5m and pressure is 800 kPa. If pressure at section 2 is 600 kPa, determine the pipe diameter at that location. Neglect losses. UNKNOWN: DIAMETER OF THE PIPE STRICTLY SHOW COMPLETE FBD AND SOLUTION MUST BE HANDWRITTEN
Water flows steadily through a horizontal 30 degree pipe bend. At the inlet point 1, the diameter is 0.3 m, the velocity is 12 m/s, and the pressure is 128 kPa gauge. At the outlet point 2, the diameter is 0.38 m and the pressure is 145 kPa gauge. Determine the forces F_x and F_y necessary to hold the pipe stationary.
A 12′′ pipe line carries oil of specific gravity 0.811 at a velocity of 80.0 ft/sec. At points A and B, measurements of pressure and elevation were 52.6 psi and 100.0 ft and 42.0 psi and 110.0 ft,respectively. For steady flow, find the lost head between A and B. indicate the free body diagram
A vessel is being filled with water through an inlet at section 1 having a diameter of 40 mm and a faucet at section 3. The velocity at section 1 is given as 5 m/s, while the discharge at section 3 is given as 0.012 m^3/ s. Assume constant water level. Use 60 mm for the diameter of the outlet at section 2. A. What is the discharge at section 2? B. What is exit velocity at section 2? C. If the water level varies and the velocity at section 2 is 8m/s find the rate of change when d is equal to 1000mm?
A liquid (SG = 0.562) is being pumped from a reservoir as shown. The pressures at points 1 and 2 are -9 psi and 41 psi, respectively. The rate of flow in the pipe is 0.898 ft3/s. What will be the rating of the pump (in horsepower) if its efficiency is 90%? Neglect energy (friction) losses in the system. Use x = 5 ft., y = 9 ft. Use 1 hp = 550 lb-ft/s. Round off to two decimal places.
As shown in figure below, oil can be siphoned from a tank using a flexible hose, provided that the end of the hose at Point B, is below the free surface in the tank at Point A. The maximum elevation of the hose is at Point C. Oil is being siphoned from the tank through a constant-diameter hose. The end of the siphon at Point B is 6.71 meters below the oil top surface level of the tank at Point A. If the gauge pressure at Point C is 90.257 KPa and the density of oil is 890 fraction numerator k g over denominator m cubed end fraction , the vertical distance between Point C and Point B in meters is
Water flows through a vertical contraction (venturi) section. Piezometers are attached to the upstream pipe and minimum area section as shown. The velocity in the pipe is 3 m/s. The difference in elevation between the two water levels in the piezometers is 3 cm. The water temperature is 10oC. What is the velocity (m/s) at the minimum area?