200 MPa 150 MPa 500 MPa

Q: Determine the principal stresses and the absolute maximum shear stress. 2.5 ksi 4 ksi 5 ksi

A:

Q: The beam is supported by two rods AB and CD that have cross- sectional areas of 13 mm² and 7.8 mm²,…

A:

Q: The stepped circular shaft made of aluminum (E = 69 Gpa, u = 0.35) is loaded by an axial force of 3…

A: Given: E=69 GPa P=3kN μ=0.35 d=12 mm D=15 mm r=2.4 mm

Q: 5 5 -5

A: Given         Major principal stress = 20 MPa Tensile stress in x direction = 5 MPa Tensile stress…

Q: Treat A as a support wall and determine the Maximum shear stress in the shaft and the rotation of C,…

A: Diameter of steel shaft d=40 mm LAC=300 mm ,LCD=400 mm ,LDB=500 mmG=75…

Q: 1. The 12 kN m torque is applied to the free end of the 6-m steel shaft. The angle of rotation of…

A: you have posted multiple questions. As per the guidelines I am able to answer one question only. So…

Q: Determine maximum shear stress Maximum principal stress-44 MPa Minimum principal stress=38 Mpa

A: Given data : Maximum principal stress σ1=44 MPa Minimum principal stress σ2=38 MPa   Required :…

Q: The stal block Shown below is Subjected to a normal stress Of 100 Mea and 85 MPa Aogether with a…

A:

Q: A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is…

A:

Q: Consider a tube having a rectangul ar cross-section as shown below. The tube is subject to two…

A: given; ⇒twisting moment (M1)=70N.m (clockwise from fixed point)⇒twisting moment (M2)=35N.m…

Q: P=70 MPa . Determine maximum principal stress

A:

Q: Determine the vertical stress increase, Ao,, at point A if q = 2895.8 kN/m. %3D 250 AN Answer ORPa…

A: Problem

Q: Q2. A mild steel shaft transmits 'P' kW at 'N' r.p.m. It carries a central load of 900 N and is…

A: Shaft is a rotating element that transmit power and rotation.

Q: The solid shaft is subjected to the distributed and concentrated torsional loadings shown, where T =…

A: To find: The diameter of the shaft. Given: The torque T is T=420 Nm. The allowable shear stress of…

Q: A mild steel shaft transmits 21 kW at 250 r.p.m. It carries a central load of 900 N and is simply…

A: Given Data  Power transmit, P=21KW N=250 rpm Load, P=900N Allowable shear stress, T=42MPa

Q: Determine the principal stresses and the absolute maximum shear stress.

A:

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A: Given: F1 = 7KN   F2 = 6KN  F3 = 2KN     F4 = 9KN

Q: Determine the principal stresses and the absolute maximum shear stress.

A: Given: The normal stress on the vertical plane is σX=20 ksi. The normal stress on the horizontal…

Q: Solve Prob. using the maximum shear stress theory.

A: Given data: Stress in horizontal direction is σx = 20 ksi. Stress in vertical direction is σy = -12…

Q: A water tank made from a steel having a thickness of 12mm has the following dimensions. Internal…

A:

Q: A 3-m aluminum tube with the cross section shown carries a 200 N-m  torque. Determine the following:…

A: Given data: L=3 mT=200 N.mG=28 GPa Need to determine the maximum shear stress in the tube and…

Q: A B E F 20 kN-m 35 kN-m 85 kN-m 30 kN-n

A: given d=0.2m = 200mm so r = 100mm

Q: Part A a. Take T = 650 N. m and T, = 1565 N. m. Determine the maximum shear stress developed in the…

A:

Q: Construct the shear-force diagram and identify the largest negative shear force. Assume a = 5.9 ft,…

A:

Q: The shaft below is hollow from A to B and solid from B to C. Determine the maximum shear stress in…

A:

Q: 1) Determine the stress components acting on the inclined plane AB. 65 MPa /30 20 MPa

A:

Q: 430 MPa PROBLEM 7.8 For the given state of stress, determine (a) the principal planes, (b) the…

A: Given: σx=6MPa σy=30MPa τxy=-9MPa

Q: A lever is attached to a shaft with a square shear key as shown. The force applied to the lever is P…

A: Given:P=300 Nσ=72 MPaL=31 mm

Q: Determine maximum shear stress Maximum principal stress=25 MPa Minimum principal stress=-5 MPa

A: Maximum principal stress, σmax=25 M PaMinimum principal stress, σmin=-5 MPa

Q: 1) Reqd: Determine Maximum Shearing Stresses for the 3 segments and eat C (2)Solid 60-mm-diameter G=…

A:

Q: Determine maximum diameter of hole that can be punched through a plate of 10mm thick,if the punch…

A:

Q: A force of P,- 550 N is exerted on control arm BC, which is securely attached to the solid 32 mm…

A:

Q: Determine maximum shear stress Maximum principal stress=33.227 MPa Minimum principal stress=22.227…

A: Given data : Maximum principal stress=σ1 Minimum principal stress=σ2   Required : Maximum shear…

Q: Determine the maximum shear stress acting at a tubular cross-section having an outer diamete mm, if…

A: Given Data : Outer diameter (Do)=100 mm=0.1 m Inner diameter(Di)=80 mm=0.080 m T=500 N-m

Q: Q1: determine the increase in vertical stresses at depth of Z=3.5 m under points A, B and C due to…

A:

Q: Determine the average normal stress at points A, B, and C. The diameter of each segment is indicated…

A: Given data: The diameter of the segment at A, dA = 0.5 in. The diameter of the segment at B, dB = 1…

Q: A cylindrical propane tank has an outside diameter of 3.25 m. If the allowable hoop stress is 100…

A:

Q: The drive shaft AB of an automobile is made of a steel having allowable shear stress of tallow = 8…

A: Given data: Allowable shear stress of the shaft, τallow = 8 ksi. The outer diameter of the shaft,…

Q: The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable axial stress of the…

A:

Q: Draw Mohr's circle that describes each of the following states of stress. 5 MPa 20 ksi 5 MPa - 20…

A: To draw the Mohr's circle for the given state of stresses

Q: A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever…

A: As per given question  P=520N D=42mm L=700 mm We have to find determine shear force applied to shear…

Q: * Your answer is incorrect. The solid circular rod has a cross-sectional area of 410 mm². It is…

A: GivenA=410mm2w=9kN/mP=3kNQ=5kNx=0.5m

Q: A 3-m aluminum tube with the cross section shown carries a 200 N-m torque. Determine the following:…

A:

Q: -1 2] nd (a) Principal stress (b) Principal directions (c) Invariant

A:

Q: Two bolts are used to form a joint connecting rectangular bars in tension as shown. Determine the…

A:

Q: Two vertical forces are applied to the beam of the cross section shown. Determine the maximum…

A: Given Data: The load acting on the beam is 25 kip each. The free-body diagram of the beam can be…

Q: 8 KN 300 mm AY loe 4m 300 200

A: Given,

Q: Two bolts are used to form a joint connecting rectangular bars in tension as shown. If the bolts…

A:

Q: 50 MPa 60 MPa 60 MPa 50 MPa

A: