Answer A-D please, it's all apart of one question 2.62.4222.01.81.6D/d -21.51.21.051.011.4121.00.2r/dto Poisson's effect The stepped circular shaft made of aluminum (E69 Gpa, и —%3D2.40.35) is loaded by an axial force of 3 kN,2.2r=2.4 mm2.0k183 kN60A12 mm16D/d-21.51.21.051.0115 mm1.4(a) Determine the average normal stress in section ABand BC of the shaft at locations away from the fillet.1210Section AB, o =Section BC, o =0.30.1r/d0.2(b) Determine the change of the diameter in section A B due to Poisson's effect.Section AB, Ad =(c) Determine the highest normal stress at the fillet considering stress concentration.At the fillet, o =(d) Determine the normal and shear stresses on the oblique surface that has an incline angle of 60º with the normalcross section of the shaft in section AB as shown.T =

The stepped circular shaft made of aluminum (E = 69 Gpa, u = 0.35) is loaded by an axial force of 3 kN, 2.4 22 r=2.4 mm 2.0 3 kN k 18 A B. 12 mm 16 D/d-2 -1.5 -1.2 -1.05 1.01 15 mm 14 (a) Determine the average nomal stress in section AB and BC of the shaft at locations away from the fillet. 12 1.0 Section AB, o = Section BC, o = 0.2 0.1 r/d 0.3 (b) Determine the change of the diameter in section AB due to Poisson's effect. Section AB, Ad = (c) Determine the highest normal stress at the fillet considering stress concentration. At the fillet, o = (d) Determine the normal and shear stresses on the oblique surface that has an incline angle of 60º with the normal cross section of the shaft in section AB as shown. O = T =

The stepped circular shaft made of aluminum (E = 69 Gpa, u = 0.35) is loaded by an axial force of 3 kN, 2.4 22 r=2.4 mm 2.0 3 kN k 18 A B. 12 mm 16 D/d-2 -1.5 -1.2 -1.05 1.01 15 mm 14 (a) Determine the average nomal stress in section AB and BC of the shaft at locations away from the fillet. 12 1.0 Section AB, o = Section BC, o = 0.2 0.1 r/d 0.3 (b) Determine the change of the diameter in section AB due to Poisson's effect. Section AB, Ad = (c) Determine the highest normal stress at the fillet considering stress concentration. At the fillet, o = (d) Determine the normal and shear stresses on the oblique surface that has an incline angle of 60º with the normal cross section of the shaft in section AB as shown. O = T =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A mild steel shaft transmits 18 kW at 450 r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa
Partial answer (a) max and min shear stress = +- 10.6 kpsi (b) vB=-0.0102 in and wB=.0234 in
A hollow shaft for a rotary compressor is to be designed to transmit a maximum torque of 4750 N-m.The shear stress in the shaft is limited to 50 MPa. Determine the inside and outside diameters of theshaft, if the ratio of the inside to the outside diameter is 0.4. [Ans. 35 mm ; 90 mm]
A solid steel shaft is to be used to transmit 5 hp from the motorto which is attached. If the shaft rotates at 175 rpm and thesteel has an allowable shear stress of 14.5 ksi, determine therequired diameter of the shaft to the nearest 1/8 in.
A thick cylinder internal diameter 240mm external diameter240mm internal diameter ‘D’ is subject to external pressure of 50MPa. Determinethe diameter ‘D’ if the minimum hoop stress in the cylinder is not to exceed200MPa.
Determine the maximum shear stress (in ksi). AT = 654 lb ft Diameter =3.7 in J =1.5in4 G = 11,000 ksi
Determine the diameters of a hollow shaft which has to transmit 40 kW at 300rev/min. If the shear stress is limited to 30 MPa. Assume the maximum torque to be 12% greater than the mean torque and that the shaft diameters are in the ratio of 1 to 1, 5.
answer this; The maximum shear stress in the section can be calculated as ???? = MPa
The drive shaft of a car with diameter 30 mm is designed to transmit a power of 50 kW when rotating at 2100 rpm. The drive shaft material has an allowable shear stress of 230 MPa. i) Determine the maximum shear stress in the shaft. ii) In order to reduce the weight of the vehicle, a hollow shaft is proposed with a maximum outer diameter of 30 mm. Determine, the maximum inner diameter iii) Determine the resultant percentage weight reduction
For the stress element shown below, which 2 points (σ, τ) in the stress domain could be used to define the diameter of the Mohr's Circle? (- 80 MPa, - 25 MPa) (50 MPa, 25 MPa) (50 MPa, - 25 MPa) (- 80 MPa, 25 MPa)
The shaft is supported on bearings that do not resist axial load. If the allowable shear stress for the shaft is Tadm = 40 MPa, determine, to the nearest 1mm, the smallest diameter that will support the load.
A steel propeller for a windmill transmits 5.7 kW at 43.4 rpm. If the allowable shear stress in the shaft must be limited to 72 MPa, determine the minimum diameter d required for a solid shaft.