21. Box Spring on a Ramp. A massless spring of natural length 10.0 cm and spring constant k = 10.0 N/m is attached to a 50-g block and held at rest 8.00 cm down an inclined plane. Then, the block was released. If the inclined plane has a friction coefficient of µ = 1.00, and an inclination of 0 = 3 radians, what is the final length of the spring after it stops moving? Answer in cm.

21. Box Spring on a Ramp. A massless spring of natural length 10.0 cm and spring constant k = 10.0 N/m is attached to a 50-g block and held at rest 8.00 cm down an inclined plane. Then, the block was released. If the inclined plane has a friction coefficient of µ = 1.00, and an inclination of 0 = 3 radians, what is the final length of the spring after it stops moving? Answer in cm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 1855 kg car has a velocity of 100 km/h when the brakes are fully applied. Assume modern traction control eliminates tire skidding. Determine time and distance to stop the car if dry-pavement static friction coefficient is 0.8.Creat a conclusion for this problem.
A ladder of length 5 m is resting against a smooth wall, its point of contact being just below a first floor window. The bottom of the ladder rests on the ground and the coefficient of friction between the ladder and the ground is 0.3. A person of mass 75 kg climbs the ladder, which has a mass of 4 kg. The bottom of the ladder is at the point of slipping, outward from the wall, just as the person reaches the mid-point of the ladder’s length. Draw a free body diagram of the ladder and calculate the maximum frictional force opposing the slipping motion. In addition, determine the angle of inclination (θ) of the ladder, when the person is at the mid-point and the ladder is on the verge of slipping.
An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the corresponding angles of lap are 160° and 210°. The smaller pulley runs at 200 r.p.m. The coefficient of friction between the belt and pulley is 0.25. It is found that the belt is on the point of slipping when 3 kW is transmitted. To increase the power transmitted two alternatives are suggested, namely (i) increasing the initial tension by 10%, and (ii) increasing the coefficient of friction by 10% by the application of a suitable dressing to the belt. Which of these two methods would be more effective? Find the percentage increase in power possible in each case.
consider the mass and pulley system in the attached file. mass m1 = 29 kg and mass m2 = 12kg. the angle of the inclined plane is given and the coefficient of kinetic friction between mass m2 and the inclined plane is uk = 0.12. assume the pulleys are massless and frictionless when mass m2 moves a distance 4.94 m up the ramp, how far downward does mass m1 move? d= ?
The crate shown is held against wedge B by a spring. The spring is 92.5% of its original uncompressed length l=2.50m , and the spring constant is given as k=1350N/m . The coefficient of static friction at all contacting surfaces is μs=0.150 . The mass of the crate is m=28.0kg . The angle is θ=14.0∘ . Neglect the mass of the wedge. Assume the crate only moves in the y direction and that wedge A cannot move.(Figure 1) Part A - Determining the normal force exerted by the crate on the wedge Determine the normal force Nc that the crate exerts on the wedge when the system is at rest. Express your answer to three significant figures and include the appropriate units. Part B - Finding the smallest horizontal force P to move the crate upward Determine the magnitude of the smallest horizontal force P that is necessary to begin moving the crate upward. Express your answer to three significant figures and include the appropriate units.
A pulley with a diameter of 4 in. can rotate about a fixed shaft with a diameter of 2 in. The coefficient of static friction between the pulley and shaft is 0.20. Determine; a. the smallest vertical force P required to start raising a 500-lb load. b. thesmallest vertical force P required to hold the load. c. the smallest horizontal force P required to start raising the same load.
The 10 N cylinder moves in a friction tube. Spring constants are k1 = 150 N / m and k2 = 200 N / m. When the system is at rest, d = 0.5 m. The system rotates around a fixed z-axis. In the case where d = 0.12 m, what is the coefficient of friction for the cylinder to have a constant velocity of 9.825 m / s?
A 3.1 meter ladder with a mass of 24 kg rests against a wall. Neglect the friction between the ladder and the wall. If the ladder is on the verge of slipping and the angle of the ladder with respect to the wall is 25◦, what is the coefficient μs of static friction between the ladder and the floor? A. 0.15 B. 0.23 C. 0.36 D. 0.50
An open flat belt is required to transmit 50 kW from a pulley of 1.5 m effective diameter running at 300 r.p.m. The angle of contact is spread over 11/24 of the circumference. The coefficient of friction between the belt and pulley surface is 0.3. Determine, taking centrifugal tension into account, width of the belt required in mm. It is given that the belt thickness is 9.5 mm, density of its material is 1100 kg/m3 and the related permissible working stress is 2.5 MPa.
A belt drive is required to transmit 12 kW power. The velocity of the belt is 9.6 m/sec. If coefficient of friction is 0.25 and the angle of contact is 150º, determine the maximum tension is the belt.
....A steam engine develops power at mean torque of 19,000 N-m and velocity of 10 m/s. The mean diameter of the flywheel rim is 1.2 meters. The coefficient of fluctuation of speed is 0.03 and the coefficient of fluctuation of energy is 0.21. Determine the thickness of the rim in mm if the width of the rim is twice of its thickness. Assume density of rim material as 7250 kg/m3.
1. If there is no friction between shaft AB and the collar, what angular velocity θ˙˙ must the mechanism have to keep the collar at r=300 mm from the vertical axis? Express your answer to three significant figures. 2. Consider the same mechanism again, with m=2.95 kg, d=225 mm, k=250 N/m, only now, instead of being smooth, the collar and shaft have a maximum coefficient of friction of μs=0.297. What is the minimum angular velocity required to keep the collar at a constant distance r=300 mm from the axis of rotation? Express your answer to three significant figures.