Answered: 21. Water flows at a rate of 10m³ /s in…

21. Water flows at a rate of 10m³ /s in a rectangular channel 3 m wide. The critical depth of flow is O A. 1.13 m O B. 2 m O C. 1.45 m O D. 1.04 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Given the Following information for a compound curve Leads with short curve I= 105°58'12" = 2,641.08…

A: Find: Length of long curve

Q: eight at 0kpa: 396 g Weight at -33kpa: 325 g Weight at -1500kpa: 291 g Weight at -3100kpa: 280g…

A: Weight at 0kpa: 396 gWeight at -33kpa: 325 gWeight at -1500kpa: 291 gWeight at -3100kpa: 280gWeight…

Q: A rectangular channel 2m wide carries a discharge of 10m³/s at a depth of 2m. Calculate the specific…

Q: A soil with a volume of 163cm^3 is sampled from a field. It weighs 221g. Then, the sample was…

Q: In a triangular channel, the critical depth for a discharge of 1.2 m³/s is 1.3 m. The critical depth…

Q: Design a rectangular footing for an 16” square corner Column with PDL = 280 kips and PLL = 180 Kips.…

Q: PART 1. AREA & VOLUME OF PRISMS Draw the indicated views for the isometric drawing below. Isometric…

A: An isometric view is given, we need to draw: 1. Top view 2. Left view 3. Front view

Q: An HSS10x10x3/16 is used as a compression member with one end pinned and the other end fixed against…

A: The section HSS 10×10×316 with one end pinned and the other end fixed against rotation but free to…

Q: The gusset plate is subjected to the forces of three members as shown in (Eigure 1). The forces are…

A: Consider vertical force equilibrium9 - 6sin - Tsin = 09 - 6* - Tsin = 0Tsin = 5.4 ...equation…

Q: The gear motor can develop 2 hp when it turns 450 rev/min. If the shaft has a diameter of 1 in. What…

A: Power developed by shaft = 2hp No. of turn=450rev/min Diameter of shaft=1 in To find Torque…

Q: .18 A series of small machine components being moved by a con- veyor belt pass over a 180-mm-radius…

A: Velocity of A (negative sign indicates the left direction)Angular Acceleration To find:a. angular…

Q: The intensity of rain fall and the time interval of a typical storm are Time interval (minutes)…

A: The intensity of rainfall and the time interval of a typical storm is given as shown in table- To…

Q: Determine the sliding factor of safety and the heel and toe stresses for a riangle gravity dam (25m…

A: To find: The sliding factor of safetyheel stresstoe stress

Q: A 30 cm square plate settle by 8 mm in the plate load test on a cohesionless soil, when the…

A: A square bearing plate with, Width of plate, Bp=30 cm = 0.3 m Settlement of plate, Sp = 8 mm…

Q: A rectangular foundation of plan size 5 (B) × 10 (L) m is to be designed to carry a load of 86.6 MN…

A: Width of the footing, B = 5m , Length of footing , L = 10m , Dry Unit Weight,γdry=20kN/m3 Saturated…

Q: 4 Which of the following gives the reaction at D in the given beam? 300N₁ 210 N/mp 100 Nm TIT777 5m…

Q: Problem Solving: Round off your final answer to 2 decimal places. 3m 1 3m 4 m 20 KN 15 kN 10 KN 1 2…

A: For the frame provided below, consider the following properties, Members along level 2: Regular…

Q: How much time (in seconds) does a person traveling on a grade of 4% at a speed of 69 mph have to hit…

A: Grade = 4%(0.04) , Initial Speed , Vi = 69mph = 69 x 1.467 = 101.22 ft/sec Distance up to the…

Q: Cablen #1] Compute for the resultant of the given concurrent force system 30KN 12 KN 25KN 715° 3…

Q: 1- A 6.5-m uniform ladder AB, with weight W, leans against a wall as shown. Assuming that the…

Q: Q2- Calculate the right of way of rural divided four-lane highway has a depressed median and it is…

A: Four lane highway median width = 4.0 m Embankment height = 6 m Lane width = 3.5 m Shoulder width =…

Q: The sluice gate shown in Figure A is a circular arc of radius 5m and angle B=60°. The depth of water…

Q: Question #4: Determine the state of stress at point A on the cross section of the beam at section…

A: Summation of moment at A; ΣMA= 0 Findind reaction force at A and B.RB×3 = 30×1 RB= 10 KN…

Q: A surface water treatment plant operates round the clock with a flow rate of 35 m³/min. The water…

A: Surface water treatment plant- Discharge, Flow rate, Q=35 m3min. Gt=4×104 Alum dosage = 25 mglit.…

Q: Use A992 steel and select a W shape using LRFD. D = 350 k L = 1000 k 35' Strong axis T 10' Figure 4…

A: Span, L = 35 ft Dead load, D = 350 k Live load, L = 1000 k A992 steel; fy = 50 ksi fu = 65 ksi

Q: For the beam shown whose rectangular cross-section is identical with base 350mm and height 750mm,…

A: The cantilever beam with the loading and support conditions is given as Rectangular cross section…

Q: 4-57. Determine the moment of this force F about an axis extending between A and C. Express the…

A: Force vector (F)=Coordinates:

Q: The vertical photograph was exposed with a 50 cm focal length camera at a flying height of 5,000…

A: Focal length f=50 cm = 0.50 m, Flying height H=5000 m, Photo scale S=1:2500, To Find- The elevation…

Q: 15. id circular rod that is 600 mm long, and 20 mm in diameter is subjected to an axial force of…

Q: A six-sided tract of land in a flat terrain is bounded by lines by connecting the horizontal control…

A: Given, X = 6, Y = 8Coordinate of A, = (500, 0)Coordinate of B, = (1000, 0)Coordinate of C, = (1200,…

Q: A cantilever beam is loaded with a uniformly distributed load of kips/ft, as shown in Figure below.…

A: Given: Required : Slope at free end

Q: Q5/ Calculate magnitude and location of the total force on one side of this vertical plane area. 1.2…

A: Determine the magnitude and location of the total force on one side of this vertical plane area.

Q: Q2/A pre-cast concrete factory was purch an advance, and the rest of the amount will be paid in the…

A: Given: Value of each installment= 17000$ Time of installments = 5 years Interest rate = 8% To find:…

Q: soil with a volume of 163cm^3 is sampled from a field. It weighs 221g. Then, the sample was…

Q: 36

Q: 12 Which of the following statements is correct about the given structure? 4 m- B 20 KN 4 m It is…

A: Determine the whether structure is stable or unstable and determinate or indeterminate.

Q: What are the major watersheds/drainage basins in VA? paragraph form

A: Here It is asked about the major watersheds or drainage basins in VA.

Q: A strip footing 1.5 m wide is located at a depth of 0.75 m (equal to the foundation thickness) in a…

A: Width od strip footing = 1.5m , Depth = 0.75m = Thickness of foundation , Unit weight of sand =…

Q: Situation 9 - An 18-m long prestressed pile weighing 3.8 kN/m is to be lifted by two cables. 25. At…

A: Udl = 3.8 kN/m Length of pile = 18 m

Q: 3 A triangular channel with apex angle 60° is carrying a uniform flow of 4.25 m³/s with a depth of…

Q: Sketch the dissolved oxygen sag curve a (100-km) (D20.40.80.100) reach of the stream below the…

A: Given: Qw=5 cumecs ; Qs=22 cumecs; BOD(5) of Waste water=55mg/l ( 200 C) BOD(5) of Stream=3mg/l (…

Q: Q2/A 50 mm diameter bracket, securely fastened to the wall as shown in figure 2 below, carries…

A: Diameter of the bracket = 50 mmIt is asked to determine the following,1. Principle stresses and…

Q: The upward flow of water through a layer of sand in the tank shown in figure has the following…

A: e = 0.50 G = 2.67 To find: 1. Effective stress at point A. 2. Effective stress at point B. 3. Upward…

Q: A cantilever beam is loaded with a uniformly distributed load of kips/ft, as shown in figure below.…

A: EI = Constant Determine the equation of the elastic curve of the beam using Double Integration…

Q: A rectangular channel 2m wide carries a discharge of 10m³/s at a depth of 2m. Calculate the specific…

A: Width, B = 2 m Depth of water, y = 2 m and Discharge, Q = 10 m3/s The specific energy ( E ) of the…

Q: A square pile of section 30 cm x 30 cm and length 10 m penetrates a deposit of clay having c = 50…

A: A square pile of section 30 cm 30 cmB = 0.3 mLength, L = 10 mA deposit of clay having c = 50…

Q: A rectangular concrete channel (n = 0.014) has a bottom width of 12.0 m, a water depth of 6.0 m and…

A: A rectangular concrete channel-Manning's constant n=0.014,Bottom width b =12 m,Water depth d =6…

Q: A 1.5 m square footing is founded at a depth of 1m (equal to the foundation thickness) in…

A: Dimensions of square footing = 1.5 m Thickness of footing = 1 m Depth of footing = 1 m Properties of…

Q: Environmental Enginee... During a recuperative test, the water is pumped out 2.8 m initially and…

A: A recuperative test- Water is pumped out 2.8 m initially, s1=2.8 m Water level rises by 1.45 m in 80…

Q: Engineering Surveying. An aircraft is flying at a ground speed of 300 kmph. The focal length of the…

A: Given; Ground speed of the aircraft = 300 km/hFocal length of the camera = 300 mmGround distance…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

21. Water flows at a rate of 10m³ /s in a rectangular channel 3 m wide. The critical
depth of flow is
O A. 1.13 m
OB. 2 m
O C. 1.45 m
O D. 1.04 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data-

VIEW

Step 2: Calculation-

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A rectangular channel flows at a rate of 1m3/s, if the specific energy before the jump is 2.5m and the depth after the jump is 2m. Determine the width if the channel if loss due to hydraulic jump is 0.30m.
Water is flowing in a rectangular channel that has a width b=3 m. If the depth of flow y = 2 m and Froud Number NF=3.3, then the flow rate(Q) in the channel is
Consider a rectangular channel of width b=7.5 m, in which the hydraulic jump occurs and one of its stays is equal to 45 cm. A flow rate Q=54 m3/s passes through the channel. Determine: a) the other conjugate tie rod b) energy losses c) type of jump that occurs d) jump length
A rectangular channel carries a discharge of 18.10m3/s when flowing 1.5m depth. If the width of the canal is 10m, determine: The specific energy, Slope of the channel if n= 0.35, and Boundary shearing stress in Pascals.
A rectangular open channel, with a constant discharge of 32m3/s, has a smooth expansion from (1) to (2) as shown in figure Q2 in the flow direction. At (1) the channel is 3.6m wide and the water depth is 2.4m . At (2) the water depth is 0.8m. Calculate the minimum energy of the flow at (1).
A rectangular channel of (4m) width and the discharge rate is (2 m³/sec) with slope of (1/3000), if the velocity is (4.5 m/sec) determine: 1- Hence hydraulic jump is possible or not. 2- Height of hydraulic jump. 3- Length of hydraulic jump. 4- Percentage of energy dissipated by hydraulic jump.
A masonry dam having a sheet piling cutoff at the upstream and is located at a reservoir site as shown in the figure. Nf= 4; Nd= 10 and K= 0.003m/min 1) compute the seepage discharge in cu MTR/day 2) compute the uplift force acting on the base; 3) compute the exit or escape gradient of the water at the downstream tip of the dam if the length of the flow field is equal to 1.80m
A rectangular channel 3.05 m wide carries 3.4 m3/s uniform flow of water at a depth of 0.6 m. Suppose that an obstruction such as a weir is placed across the channel with the height of 0.2 m above the bottom. (a) Does this weir cause a hydraulic jump upstream of the weir? Why or why not? (b) Calculate the flow depth above the weir, and just upstream of the weir. Classify the surface profile occur upstream of the weir. Sketch the resulting water-surface profile and energy line, showing the critical depth yc and normal depth yo.
Water at 20°C ( ρ= 999.7 kg/m3 and μ=9.7720 x10-4 kg/m · s) is flowing steadily in a hexagonal cross sectional pipe b=1.5cm, 20-m-long at an average velocity of 1.2 m/s. Determine: (a) Hydraulic diameter. (b) The pressure drop. (c) The head loss. (d) The pumping power requirement to overcome this pressure drop.
Water flows in a wide channel at Fr=4.5 and y1 = 2.40 m. If the flow undergoes a hydraulic jump, calculate: y2
A flow of 30 m3 /s occurs in a trapezoidal channel having a base width of 3 m, side slopes 1 vertical to 2 horizontal. Determine the critical depth, yc.
Total head (energy) is constant along a pipe system and is 25 m. At Point B, the flow rate is 1.2 m3/s where the rectangular pipe has a height of .5 m and a width of .4 m. What is the static head at Point B, in m?