Answered: A square pile of section 30 cm x 30 cm…

A square pile of section 30 cm x 30 cm and length 10 m penetrates a deposit of clay having c = 50 kN/m² and the adhesion factor = 0.8. The load carried by the pile shaft only is

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter12: Pile Foundations

Section: Chapter Questions

Problem 12.12P

See similar textbooks

Related questions

Q: What is Mohr's circle of stress? At a point in an elastic material, a direct tensile stress of 60…

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. If 1 grid…

Q: normal-weight concrete rectangular beam has dimensions b = 285 mm by h = 634 mm with an effective…

A: Given f'c = 27.6 MPa fy = 414.7 MPa Width of beam= 285 mm Note According to the company…

Q: A simple beam with span is loaded with counterclockwise moment M at the right support. Compute the…

Q: . If a soil sample has a dry unit weight of 19.5 KN/m3, moisture content of 8%and a specific gravity…

Q: isolate and show the diagram of B-2 for the computation of loads and support reactions at designated…

Q: 1. a) A mass is hung as shown in Fig. Q1(a). The tension in the cable AB is 500N. Solve with the aid…

A: Given Data Find the mass (m) if the system in the equilibrium.

Q: Do the ff using USD: 1.Designing ultimate moment using moment distribution method. 2. b and d 3.main…

A: Solution: Factored load: Wu=1.2 DL+1.6 LL=1.2×15+1.6×20=50 kN/mPu=1.6 LL=1.6×25=40 kN Fixed end…

Q: 1) Please find the extreme values of deflection, bending moment and shearing force.

Q: 2. Determine the largest load P that can be applied to the frame without causing either the average…

A: Given Square cross section of side 25 mm σ=150 MPaτ=60 MPa To find largest load P

Q: L Ет EI К ЗЕТ (21) P K,

Q: For each of the following compounds, determine the carbonaceous, nitrogenous, and total theoretical…

A: When a compound is oxidized it requires a certain amount of oxygen to get the final oxidized…

Q: QUESTION: Solve for the following: Q. Horizontal component of hydrostatic pressure & its location b.…

A: Given data: A Circular gate which is 6 m below the water level making angle of opening 55° with…

Q: What does Bowen's reaction series describe? Choose all the correct answers. It describes the…

A: This question is related to the Engineering Geography from Soil Mechanics from Civil Engineering.…

Q: In a one-lane road V=1800veh/h. what is the probability that a vehicle will arrive in the next five…

A: Given: Vehicle arrival rate = 1800veh/h Required: Probability of a vehicle arriving in next five…

Q: 2. Determine the largest load P that can be applied to the frame without causing either the average…

Q: 2 - Two concentric cylinders are covered by a rigid plate that carries an axial load, as shown in…

Q: B A L1 W d tw do bf L2 Figura 1. Elevación frontal de marco estructural D H1 Figura 2. Detalle de la…

A: I am solving first three sub parts as bartleby guidelines..

Q: 2.51 A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB…

A: Given:- Portion AB is made of steelEs=200 GPaαs=11.7×10-6 /oCPortion BC is made of brassEb=105…

Q: Models are used in many different contexts nowadays. Is it possible to arrange the models?

A: In engineering, models refer to simplified representations of complex systems or processes that can…

Q: Solve for the reactions

A: Given Data Determined the support reaction. Let's solve using Moment Distribution Method.

Q: I am looking at the solution to 5.1.1 in the Water resources engineering by Larry W Mays, My…

A: From the Water resources engineering by Larry W Mays Solution 5.1.1 An 8-ft wide rectangular channel…

Q: How to get the shear force diagram?

A: Given: Support reactions: RA = 97.85 kN RB = 325.25 kN RC = 166.9 kN To find: The shear force…

Q: A normal-weight concrete rectangular beam has dimensions b = 285 mm by h = 634 mm with an effective…

A: Answer (1) Calculation of gross moment of inertia of the section Gross moment of inertia is given…

Q: Question No. 9 In a reinforced concrete section, the stress at the extreme fibre in compression is…

A: Given- Neutral axis depth from the compression fiber- y=58 mm M25 grade of concrete, fck=25 N/mm2…

Q: many www.my Q3: A simply supported beam ABCDEF of 5 m length and loaded as shown in Fig. Q3. Find…

Q: Your have complete the leveling of a centerline project in the field and now you must plot the…

Q: The picture above the represents a neighborhood (A, B, Cs, D green areas) in Flatfland. Using the…

A: To determine the location for a new grocery store.

Q: For the structure shown below, the slope deflection equation of the member BA i.e. MBA 40kN- A B d C…

A: Given data- A structure is given as shown- To Find- The slope deflection equation for member BA…

Q: 2. From the figure shown, the piston and the weight W are at the same elevation. The face of the…

A: Given data in question Load 45 kg Span 9 m Area 13 & 30 cm2 Specific gravity 0.8 To find out…

Q: ive some insights and reaction about the Comparison of the Current Construction Practices of a…

A: To , Give some insights and reaction about the Comparison of the Current Construction Practices of a…

Q: Problem 4. Determine the horizontal and vertical reactions at A and C of the two-member frame. 3…

A: Given : Required : Horizontal and vertical reaction at A and C

Q: For a 2-D flow field, the stream function y is 3 given as y==(y² - x²). 2 The magnitude of discharge…

A: Given- 2-D flow field stream function- ψ=32y2-x2points (0,3) & (3,4).

Q: A volume of 1 cu. meter of water is subjected to a pressure increase of 18 MPa Compute the change in…

Q: the mid span. shown in Fig. i need clear ans by hand and solve very very fast in 20 min and thank…

Q: A Find by Section Method and Join Method: 3 B Hawe Bridge 50 3′ E D 50 3 F G 50 3' H A

A: To find the member forces in the given truss by both methods.

Q: The observed altitude of ß-ursae Minoris at lower and upper culminations are 29° 58'15" and 60°…

Q: Q8. Irrigation Engineering Calculate the size of drain at the outlet Given: Area of drainage…

A: Given data- Area A=50000 m2,Manning's constant n=0.013,Drainage coefficient DC=1.1 cm,Tile grade…

Q: An isolated three-phase signal is being designed for optimum cycle length of 90 s. The total lost…

Q: 1. The bar has a cross-sectional area of 400*10-6 m2. If it is subjected to a uniform axial…

A: Given, Cross sectional area, A = 400 x 10-6 m2 or 400 mm2 w = 8 kN/m

Q: 4. What are the fields of Environmental Engineering? 5. What is Environmental Resource? Give atleast…

A: To Determine: 4 .What are the fields of Environmental Engineering? 5 .What is Environmental…

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses…

Q: 5. Given the hydraulic press shown in the figure, calculate the force "P" required to raise a load…

Q: Determine the smallest force F that must be applied along the rope in order to cause the curved rod…

A: Objective: To determine the required minimum value of force F. Given: Moment at A required to…

Q: A section is given below. The beam has a span of 4m with Fy= 250 MPa. Compute for the following: a.)…

A: Answer (1) Calculation of yield Moment capacity of beam We know that yield Moment capacity of beam…

Q: 1. Rigid member ABC is connected to two elastic bars, as shown in the figure. Bar AD is heated by…

A: Given:- Properties of copper bar areA=700 mm2E=90 GPaαT=20×10-6/oCProperties of steel bar areA=500…

Q: 3. Determine the normal force between the crate and the surface 4. Determine the force P needed to…

A: Given- W = 856 N Frictional coefficient - μs = 0.3 height of block = h = 2 m Width of block = b = 1…

Q: After watching Small Laude’s vlogs, you decided that you want to pay for your dream car in cash. Not…

A: Given data: Total cost of car, S=$40000 Number of years of investment, n=8 Annually amount to be…

Q: B) Cork is used as for sealing sparkling wine bottles. Aside from friction, why not use rubber to…

Q: 300 mm B 600 mm 400 N·m 600 mm 200 N·m 800 N-m The 50-mm-diameter A992 steel shaft is subjected to…

A: Given For A992 steel G= 75GPa outside diameter = 50 mm inside diameter = 35.5 mm To find the angle…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

A square pile of section 30 cm x 30 cm and length 10 m penetrates a deposit of clay
having c = 50 kN/m² and the adhesion factor = 0.8. The load carried by the pile shaft
only is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A square prestressed concrete pile with a cross section 0.3 m by 0.3 m is driven 15 m into overconsolidated clays with properties as defined: From the ground surface to a depth of 7 m, the unit weight is 17 kN/m3 and the shear strength cohesion cu is 70 kPa; below 7 m, the soil unit weight is 18.5 kN/m3 and cohesion is 105 kPa. Use the total stress α-method to calculate both the design downward axial capacity and upward axial capacity, using a factor of safety of 3 (downward and upward).
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2 and ?s = 0.2.
Refer to Figure 18.9. A cantilever sheet pile is driven into a granular soil where the water table is 2 m (L1) below the top of the sand. The properties of the sand are =40, =17.5kN/m3, and sat=19kN/m3. It is proposed to excavate to a depth of 6 m (L) below the ground level. Determine the actual depth to which the sheet pile must be driven (L + D), using the net lateral pressure diagram. Note: Dactual=1.3(L3+L4)theory
A 600 mm diameter and 25 m long driven concrete pile carries a column load of 1200 kN. It is estimated that the shaft carries 900 kN and the point carries 300 kN. Determine the settlement of the pile head using the Poulos and Davis method with the following data: Es = 25 MN/m2, Ep = 30,000 MN/m2, and s = 0.2
In Problem 18.4, find the maximum bending moment in the sheet pile and determine the required section modulus, assuming an allowable stress of 190 MN/m2. 18.4 Refer to Figure 18.13. Given L1 = 1.5 m, L2 = 3 m; for the sand, =33, =16.5kN/m3, sat=19.0kN/m3; and, for the clay, c=50kN/m2, =0, sat=20kN/m3. Determine the depth of sheet pile required, allowing for a 50% increase from the theoretical estimate.
Refer to Figure 18.26b. Let L = 15.24 m, fill = 17.29 kN/m3, sat(clay) = 19.49 kN/m3, clay = 20, Hf = 3.05 m, and D = 0.406 m. The water table coincides with the top of the clay layer. Determine the total downward drag on the pile. Assume that = 0.6 clay. FIG. 18.26 Negative skin friction
Figure 18.26a shows a pile. Let L = 20 m, D = 450 mm. Hf = 4m, f = 17.5 kN/m3, fill = 25. Determine the total downward drag force on the pile. Assume that the fill is located above the water table and that = 0.5 fill. FIG. 18.26 Negative skin friction
Figure P12.36 shows a 3 5 pile group consisting of 15 concrete piles of 400 mm diameter and 12 m in length. What would be the maximum load that can be allowed on the mat with a factor of safety of 3? The piles have a center-to-center spacing of 1200 mm.
Consider a 15 m long concrete pile with a cross section of 0.45 m x 0.45 m fully embedded in sand.For the sand, unit weight, γ = 17 kN/m3 and soil friction angle, ϕ’ = 35o. Estimate the ultimate point??? with each of the following:1.1 Meyerhof’s method (Ans: 1014 kN)1.2 Vesic’s method (Ans: 1754 kN)1.3 Coyle and Castello’s method (Ans: 2479 kN)
Problem #1 The figure below shows a cantilever sheet-pile wall penetrating a granular soil. Here, L1 = 4 m, L2 = 8 m, unit weight above water table= 16.1 kN/m3, saturated unit weight = 5 18.2 kN/m3, and friction angle of sand = 32 degrees. a. What is the theoretical depth of embedment, D? b. For a 30% increase in D, what should be the total length of the sheet piles? c. Determine the theoretical maximum moment of the sheet pile. d. If the allowable flexural stress = 170 MPa, compute the required section modulus of the sheet pile.
Determine the ultimate load capacity of a circular pile with diameter D = 20 cm installed in asaturated soft clay. The pile is embedded 10 m into the ground. According to measurements, thesoil exhibits an undrained shear strength according to the linear relationship: Su = 2+1.6z, wherez is the depth in meters and Su is the undrained shear strength in kPa. The soil's unit weight canbe assumed as 18 kN/m3
Please help me solve3.8 The soil profi le at a site for an offshore structure is shown in Figure P13.8. The height of the pile above the sand surface is 15 m. Determine the allowable load for a driven closed-ended pipe pile with diameter 1.25 m and embedded 10 m into the stiff clay. A factor of safety of 2 is required