(25 pts) A patient is coupled by 5pF stray capacitance to a 220V 50HZ ac power-line bus while his body is insulated from ground. The resistance experienced from the right side of the circuit, Za is measured to be 4MQ. Find the voltage, Volt) and the voltage, I.(t) by using phasor techniques.

(25 pts) A patient is coupled by 5pF stray capacitance to a 220V 50HZ ac power-line bus while his body is insulated from ground. The resistance experienced from the right side of the circuit, Za is measured to be 4MQ. Find the voltage, Volt) and the voltage, I.(t) by using phasor techniques.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2MCQ: If the rms phasor of a voltage is given by V=12060 volts, then the corresponding v(t) is given by...

See similar textbooks

Related questions

Q: The voltage (in Volts) across an element is given as v(t) = 50 cos (6ft + 28.3") whereas the current…

A: The voltage across an element is given as v (t) = 50 cos (6ft + 28.3°) And current through the…

Q: A load is supplied the complex power S = 60 + j80 VA by a voltage source of 50 cos 377t V. Find the…

Q: f) A network has two branches in parallel. One branch contains impedance Za and the other branch has…

A: Given data, Two branches connected in parallel, Circuit diagram is given by,

Q: The sending-end voltage in the circuit seen is adjusted so that the load voltage is always 13,800…

A: Circuit diagram is given, (a) Frequency is given f = 50 Hz Minimum power dissipation is occurs when…

Q: An air line has characteristic impedance of 70 and phase constant of 3 rad/m at 100 MHz. Calculate…

A: Wave is function of space and time. The mode at which waveguide have lowest frequency is said to be…

Q: Problem 1.5: A source voltage of 240 Vs is applied to a 30Z30° ohms load impedance. Find the average…

Q: Q5. A single phase overhead transmission line has a supply voltage of 34 kV and a sending end…

Q: A circuit branch is found to have an equivalent impedance of Z=120−j45Ω. It is given that this…

A: Impedance: Impedance of a circuit is the combination of all the resistance as well as reactance. It…

Q: A building, supplied by a 230 Vrms source and with inductive loads, has an average consumption of…

Q: Problem: An industrial load takes 20 kW at 0.71 pf lagging from a 440 volt RMS supply. If a capa…

A: Industrial load 20KW at lagging power factor 0.71 Voltage 440V Now connect capacitor of rating…

Q: Q5. A single phase overhead transmission line has a supply voltage of 34 kV and a sending end…

Q: A transmission line with 50 ohm characteristic impedance feeds the ZL = 100 ohm load with a…

A: The equivalent circuit is Given: Characteristics impedance,Zo=50 Ω Load Impedance, ZL=100 Ω Power…

Q: An engine consumes 50 kW at a power factor 0.8 lagring.from a 220 Vrms and 100Hz line, find…

Q: V1 C1 220 Vrms 10uF 60 Hz 0° Computed Values Compute the expected power factor of the circuit given…

Q: The characteristic impedance of a losseless transmission line is 60N. Find the inductance of the…

A: DISTORTION-LESS LINE: A line in which a wave propagates without any distortion is called a…

Q: For the given circuit, Is 2 kW 1kV ar (cap.) 2 kV A 4 kW 0+ j100Vrms |0.7pf leading 0.9pf lagging…

Q: The figure below shows an RLC electrical network operating on alternating current. A load impedance…

Q: Circuit Diagram V1 R1 220 Vrms MA 150 Ω 60 Hz 0.⁰ L1 100mH Computed Values Compute the expected…

A: Power factor is the measure of how effectively the incoming power is used in an electrical system. A…

Q: + V1 10Vrms J50Hz 0° V1 = 10 /0° R1 100 Ω L1 160mH C1 :320μF

Q: The voltage across the circuit breaker is given by vV; = Vm (1-cos →), prove tha the maximum…

A: Given expression for voltage across circuit breaker (restriking voltage) , differentiate the…

Q: Q2: For the circuit shown below, determine the apparent power delivered by the source, power…

Q: The maximum value of the alternating voltage and current are 400V and 20A respectively in a circuit…

A: Given:Vmax=Vm=400VImax=Im=20AAt:t=0, V=283V and 10Af=50 HzSo ω=2πfω=100πω=314

Q: The maximum values of the alternating voltage and current are 400 V and 20 A respectively in a…

Q: A single phase AC chopper supplies a pure inductive load of 0.02H from 220V, 50HZ AC supply. The…

Q: Q1. A single phase overhead transmission line has a supply voltage of 34 kV and a sending end…

Q: Exercise#2: We have a load with an impedance given by Z = 30+j 40 Q. The voltage across this load is…

Q: Find: 1. Voltage at the source (no capacitors are installed) 2. Capacitors are installed at the load…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: A building with inductive loads has the average consumption of 40kW and 26kVAR. At the are location…

A: In this question we need to find a average current , effective impedance and surcharge

Q: Lance Smile operated two loads in parallel. The loads draw a total of 3kW at a 90% power factor…

A: Given that Total Load (LT) = 3kW @ 0.9pf lagging Given that Load 1(L1) = 1000W @ 0.8pf lagging…

Q: Problem 1 Businessman Lance Smile own two large malls in Basilan Island. Both malls are connected in…

A: Given,Operating voltage,V=13.8kVrmsImpedance,Z=1+j2.5ΩFor mall 1,P1=400kWcosθ1=0.8 laggingFor mall…

Q: An industrial load is modeled using the combination, in parallel, of a capacitor and a resistor, as…

Q: Problem 1 Businessman Lance Smile own two large malls in Basilan Island. Both malls are connected in…

A: A closed path, where electric current can flow defined as an electric circuit. It is various…

Q: Q5. A single phase overhead transmission line has a supply voltage of 34 kV and a sending end…

A: A single phase overhead transmission line, Voltage V=34KVCurrent I=40Acosϕ=0.8 p.f laggingResistance…

Q: If a current 5.0 A lags the applied voltage 230 V by an angle o, it can be resolved into two…

Q: Solution in phasor domain representation is a method that can both consider the steady state and…

A: A phasor is represented only for steady state Two waves are said to be in phase if the phase…

Q: In an electric power system, it is given that the effective impedance of the generator station is Rs…

Q: Unless given, use the: POLAR FORM for voltage and current, RECTANGULAR FORM for impedance. Consider…

Q: The voltage (in Volts) across an element is given as v(t) = 50 cos (6ft + 10.2°) whereas the current…

Q: trigonometrical expressions for the instantaneous values of p.d. and the current at time t.…

Q: The circuit given below is operating in the sinusoidal steady state. Find the value of w if i, =…

A: Given: A circuit operating in sinusoidal steady state. According to question: ∵io=40sinωt+21.870mAIn…

Q: Given that the steady-state AC circuit shown operates at a frequency of 400 rad/sec, find the…

Q: Given a sinusoidal voltage source in series with R,L, and C. The sinusoidal frequency is 600 Hz. R=2…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: 3. An industrial load is supplied through a transmission line that has a line impedance of 0.5 +…

A: The electrical devise which is store a electrical energy in electric field called as a Capacitor.…

Q: Find the steady state expressions for the currents i,, ip, and i, using nodal analysis. The source…

Q: Consider the circuit diagram where Vs = 230020 Vrms Z, Z, Z, Find: 1. The apparent power delivered…

Q: Where N=5 and the value of the capacitance C = 1.5 microfarad.. the average power supplied by the…

Q: Businessman Lance Smile own two large malls in Basilan Island. Both malls are connected in parallel…

A: Power factor: It tells how much the active power is utilized by the circuit from the apparent power.…

Q: A 100 km telephone line has a series resistance of 4 Ω/km, an inductance of 3 mH/km, a leakage…

A: The conventional telephone lines were made up of long conducting wires, which enabled the…

Concept explainers

Star Delta Conversion

Find the input resistance between points A and B of the following resistive network:

Question

A patient is coupled by 5pF stray capacitance to a 220V 50Hz ac power-line bus while his body is insulated from ground. The resistance experienced from the right side of the circuit, Za is measured to be 4MΩ.
Find the voltage, Vo(t) and the voltage, Io(t) by usingphasor techniques.

(25 pts) A patient is coupled by 5pF stray
capacitance to a 220V 50HZ ac power-line bus
while his body is insulated from ground. The
resistance experienced from the right side of
the circuit, Za is measured to be 4MQ.
E Za
1ΜΩ
Vo
Find the voltage, Vo(t) and the voltage, I.(t) by
using phasor techniques.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a certain circuit supplied from 50 Hz mains, the potential difference has amaximum value of 500V and the current has a maximum value of 10A. At the instantt=0, the instantaneous values of the p.d. and the current are 400V and 4Arespectively, both increasing positively. Assuming sinusoidal variation, statetrigonometrical expressions for the instantaneous values of p.d. and the current attime t. Calculate the instantaneous values at the instant t=0.015s and find the angle ofphase difference between the p.d. and the current. Sketch the phasor diagram (neednot be to scale).
The feeder is to be used with an antenna for which an inductive reactance is measured as j60 Ohms at 1.7 MHz. The resistive part of the antenna’s impedance is measured as 80 Ohms. Using the online impedance matching calculator, design a suitable impedance-matching network for each of the two cables if the coaxial cable has a characteristic impedance of 75 Ohms and the twin lead cable has a characteristic impedance of 300 Ohms, so that the inductance is in the longitudinal branch, while the capacitor is in the transversal branch of the impedance matching network. Do not round the resulting values.
S.2) The serial impedance of the 300 km power transmission line is 23 + j75 ohm / phase and the shunt acceptance is j500 microS / phase. A power of 50 MW with a power factor of 0.88 under 220 kV interphase voltage from the end of the power transmission line being shot. Using these data of the energy transmission line, a) Characteristic impedance of the energy transmission line, b) Natural apparent power of the energy transmission line according to the 220 kV interphase operating voltage, c) The values of the line parameters A, B, C and D of the transmission line using hyperbolic functions, d) Calculate the maximum power that the power transmission line can transmit.
A SERIES RC CIRCUIT TAKES A CURRENT WHOSE EQUATION Is 2 sin (754t+40) AMPERE. WHEN CONNECTED TO A SOURCE OF EMF HAVING THE EQUATION e = 340sin 754 VOLTS. CALCULATE, (A) THE VALUE OF Z, R, AND XC, (B) CAPACITANCE, AND (C) AVERAGE POWER.
Find the resultant Z of these three voltages and express it in the form Zm sin (ωt ± φ) using the data which contains three AC voltages.. Z1= 80 sin ωt volts Z2= 60 sin (ωt + π/2) volts; Z3= 100 sin (ωt – π/3) volts. Find an expression for the instantaneous value of the current flowing, which is in the same form using the condition below. When the found resultant voltage is applied to a circuit consisting of a capacitance of 17.3 Ω reactance and 10-Ω resistor connected in series
Find the resultant Z of these three voltages and express it in the form Zm sin (ωt ± φ) using the data which contains three AC voltages.. Z1= 80 sin ωt volts Z2= 60 sin (ωt + π/2) volts; Z3= 100 sin (ωt – π/3) volts. Find an expression for the instantaneous value of the current flowing, which is in the same form using the condition below. When the found resultant voltage is applied to a circuit consisting of a capacitance of 17.3 Ω reactance and 10-Ω resistor connected in series. Thanks.
A motor draws 680 W at 156 Vrms 60Hz. The motor is operating at a lagging power factor, with a power factor angle of 45 deg.. Determine the capacitance (in microFarad) required to correct the power factor so that the power factor angle becomes 15 deg, lagging. (Give answer in 2 decimal places. Unit is not required)
The load impedance absorbs 2.5 kW and generates 5 kVAR. The sinusoidal voltage source develops 7.5 kW.1. a) Find the values of inductive line reactance that will satisfy theseconstraints.2. b) For each value of line reactance found in (a), show that themagnetizing vars developed equals the magnetizing vars absorbed.
When connected to a 120 V (rms), 60-Hz power line, a load absorbs 4kW at a lagging power factor of 0.8. Find the value of Capacitance, C, necessary to raise the power factor to 0.95 lagging.
A dc transmission facility is modeled by the approximate series circuit shown below. If the load voltage is known to be Vload= 458.3 kilovolt (kV) what is the power loss in the line in megawatt (MW)? Write two(2) decimal places in your answer.
NEED ASAP Pleas answer this problem Maximum Average Power Transfer Pls show full and complete solution
A transmission line with impedance of 0.085 + j 0.32 Ω is used to deliver power to a load. The load is inductive and the load voltage is 200∠0° Vrms at 60Hz. If the load operates at 20 kVA with a power factor of 0.75 determine the real and quadrature power losses in both the load and the line and the source voltage phasor.