3-49 The pressure difference between an oil pipe and water pipe is measured by a double-fluid manometer, as shown in Fig. P3-49. For the given fluid heights and specific gravities, calculate the pressure difference AP = P3 - PA A Glycerin SG = 1.26 Water SG - 1.0 Oil SG = 0.88 60 cm 10 cm B 15 cm 20 cm Mercury SG = 13.5 FIGURE P3-49

3-49 The pressure difference between an oil pipe and water pipe is measured by a double-fluid manometer, as shown in Fig. P3-49. For the given fluid heights and specific gravities, calculate the pressure difference AP = P3 - PA A Glycerin SG = 1.26 Water SG - 1.0 Oil SG = 0.88 60 cm 10 cm B 15 cm 20 cm Mercury SG = 13.5 FIGURE P3-49

Name: 3-49 The pressure difference between an oil pipe and waterpipe is mea
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 3-49 The pressure difference between an oil pipe and waterpipe is measured by a double-fluid manometer, as shown inFig. P3-49. For the given fluid heights and specific gravities,calculate the pressure difference AP = Pe - PAGlycerinSG = 1.26WaterSG

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
the gauge pressure of the air in the tank is shown in Fig. p3-49 is measured to be 65 kPa. Determine the differential height H of the mercury column.
Open tank (4.5 m long, 2.5 m height and 3 m wide) contains liquid (S-0.75) to height 1. m. If this tank is accelerated along its length on a horizontal truck at a constant value of 3.5 m/s, determine pressure at the bottom of the tank at front and rear edges (in kN/m). (take y=9.8 kN/m for water)
Find the difference in pressure between tanks A and B in kPa shown in Fig. 2-64 if d1, d2, d3, and d4 are equal to 320 mm,150 mm,494 mm, and 166 mm, respectively.
Plz answer I will rate !:) A right circular cylindrical tank with its circular base on the ground is full of water. The diameter of the base is 4m and the height of the tank is 4m. Set up a Riemann sum to approximate the hydro static force against the lateral wall of the tank. Then express the force as an integral and evaluate it.
In the Fig. is shown the cross-section of the tank full of water under pressure. The length of the tank is 2.5 m. An empty cylinder lies along the length of the tank on one of its corners as shown. Find the horizontal and vertical components of the force acting on the curved surface LMN of the cylinder
An open manometer, shown in the figure, is installed to measure the pressure in a pipe carrying an oil (SG = 0.82). If the manometer liquid is carbon tetrachloride (SG = 1.60) determine the pressure in the pipe (in N/m2). Find the pressure head in meters of water column height.
Find a) the total force on gate AB in KN and b) the position of the center of pressure in m with respect to the bottom of the pond. Assume that the gate is 8 feet wide, that 1ft = 0.3048m, and that 1PSI = 6897.1 Pa
Determine the magnitude of the force on the inclined gate 1.5m by 0.5m shown in the figure. The tank of water is completely closed and the pressure gage at the bottom of the tank reads 90,000 N/m2. Use 9800 N/cubic meter for water? Ans: 48022.5N
In the manometer above, point 2 is open and is exposed to the surroundings. Also, the water tank is pressurized by air from the inside as shown in the figure. If h1 = 22cm, h2 = 0.35m, and h3 = 47cm, and assuming that the acceleration due to gravity is 9.81m/s2, (density of water = 1011 g/L, density of oil = 770 kg/m3, density of mercury has a density of 13.75 kg/dm3) A) Calculate the gauge pressure (in torr) of the air inside the tank. B) Show in your diagram all the parts that can be cancelled in the pressure balance. C) Calculate the pressure at point C (in kPa).
Shown in the figure, Fluid 1 is flowing in a horizontal tube and a U-tube manometer containing Fluid 2 is connected to point 1 and 2. The specific weights for Fluid 1 and 2 are and , respectively. If the specific weight are =8.00 kN/m3, =10.00 kN/m3, and h1=0.10 m, h2=0.20 m, calculate the pressure difference between the two points, p1-p2=_________(kPa)
The round handle of a faucet is affixed to a shaft that lets a valve to be open and closed every time the round handle is rotated. Give the radius of the handle if the shaft has a diameter of 1 cm and the MA of the machine is 8.