3- Consider the following 1D reservoir, where steady state, single phase oil flow takes place. This reservoir has homogenous property distribution of F =25% and k=18md. Figure below shows the uniform dimensions of the finite difference blocks. The boundary conditions at extreme ends are no flow. Well in grid block 4 produces at a rate of 3500 STB/D. Obtain pressures of each blocks. Also note that m=20 cp, B=1, c=. 9sc=-150 STB/D 1,000 ft 75 ft 1,000 ft P=3000 psia P=4000 psia b=0.001127, a=5.615

3- Consider the following 1D reservoir, where steady state, single phase oil flow takes place. This reservoir has homogenous property distribution of F =25% and k=18md. Figure below shows the uniform dimensions of the finite difference blocks. The boundary conditions at extreme ends are no flow. Well in grid block 4 produces at a rate of 3500 STB/D. Obtain pressures of each blocks. Also note that m=20 cp, B=1, c=. 9sc=-150 STB/D 1,000 ft 75 ft 1,000 ft P=3000 psia P=4000 psia b=0.001127, a=5.615

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The fluid in Figure 58 is CO2 at 20 ° C. Neglect losses. Say p1 = 179 kPa and the pressure gauge fluid is Merian red oil (S = 0.827), estimate (a) p2 and (b) the gas flow in cubic meters per hour.
Take the densilty and pressure values at 7km, and then apply Bernoulli equation. I think this is the method to solve the problem,If there any you can proceed with that. Please do it fast ,Very urgent. Question 1: . Consider an airplane flying at a standard altitude of 7 km with a velocity of 300 m/s. At a point on the wing of the airplane, the velocity is 400 m/s. Calculate the pressure at this point.
An incompressible fluid (kinematic viscosity =7.4x10-7 m2/s, specific gravity=0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates,find the shear stress in Pascal on the surface of top plate.
Taylor number (Ta) is used here to describe the ratio between the inertia effect andthe viscous effect. By applying Buckingham Pi’s Theorem, determine an equation forTa as a function of the radius of inner cylinder (r), cylinder tangential velocity (v),fluid dynamic viscosity (μ), gap distance (L) and fluid density (ρ).
1 In a given industrial process, oil of density p circulates inside the inclined duct of Figure 1. A U-tube manometer, with a fluid of density p, measures the pressure difference between points l and 2, as shown in the figure. The flow in the duct is stationary, so the fluids in the pressure gauge are stationary. (a) Find an analytical expression for p1-p2 as a function of the parameters of the system. (b) discuss what conditions of h are necessary for there to be no flow in the duct. (c) What conditions for there to be upward flow from 1 to 2? (d) What conditions for downward flow, from 2 to 1?
Fluid mechanics, I need solutions in 15 minutes please. MCQ/Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. A-Fx = 257.430 kN and Fy = 59.801 kN B-Fx = 164.018 KN and Fy = 37.229 KN C-Fx = 269.894 kN and Fy = 65.526 KN D-Fx = 98.182 kN and Fy = 20.002 KN E-Fx = 234.789 kN and Fy = 52.418 kN F-Fx = 187.005 kN and Fy = 42.182 KN G-Fx = 119.956 kN and Fy = 25.550 KN H-Fx = 141.327 kN and Fy = 31.171 KN I-Fx = 288.147 kN and Fy = 69.098 KN J-Fx = 213.112 kN and Fy = 47.903 KN
TOPIC: FLUIDS AT REST AND MOTION Water flows through a horizontal pipe with a diameter of 4 cm at a speed of 6 m/s with apressure of 400kPa at point A. At point B, the diameter is 2 cm. (a) What is the speed of water at point B. (b) Calculate the pressure at point B. Please help me solve this problem with complete solution. Please include an illustration. Thank you tutor!
Give me right solution with clear calculations. A closed cylindrical tank 1.89m high and 0.99m in diameter contains water of height 1.35m. When the angular velocity is constant at 20rad/sec What is the area (m 2) uncovered at the bottom? A. 0.1 B. 0.3 C.0.7 D. 0.07 If it is rotated at 15rad/sec and the air has a pressure of 200kPa what is the minimum pressure at the bottom of the tank in KPa? A. 245.10 B.145.10 C.201.45 D.210.54
Water is flowing at 0.075 cu.m./sec through a glazed porcelain pipe 400m long and 200mm diameter. The pipe roughness is 0.0015mm. Properties of water: Density: 1,000 g/cu.m., viscosity = 0.001 N-m/sec. What is the velocity of water in the pipe? What is the Reynold's number? Steady State flow exists in pipe that undergoes a gradual expansion from a diameter of 6in. Assuming constant density and the inlet flow velocity is 22.4 ft/sec. What is the size of the exit pipe if the exist flow velocity is 12.6 ft/sec?
Example: A fan of diameter 0.7 m running 1500 rpm delivers 140 m3/min of air at 15C against 75 mm of water total pressure when the total effeciency is 86%. Determine the volume of air delivered, total pressure and power consumed, if (a) the air temperature is 50C. (b) the air temperature is 50C and the fan speed is 1700 rpm. (c) the same conditions as (b) but a 0.6 m diameter, geometrically similar fan is used.
Example 3.8.In Example 3.7 we considered a vacuum system with zero leaks. No real vacuum systems aretotally leak-free; engineers work very hard to keep the leakage rate as low as possible. If thetank in Example 3.7 has a leak of 0.0001 lbm/min of air, what will the pressure-time plot looklike, and what will be the final pressure? ex: 3.7 is posted
The glycerin at 40 C flows through a horizontal cylindrical pipe. The length of the pipe is 70 m and the diameter of the pipe is 4 cm. The flow is steady state and fully developed. The velocity of the fluid at the centerline is 6 m/s. PLEASE DRAW THE FIGURE OF THE PIPE and labet the necessary info . The density and the viscosity of the glycerin at 40 0C are 1252 kg/m3 and 0.3073 kg/m.s, respectively. Is this a laminar flow? Write an equation for the variation of the local flow velocity with the radial direction. Determine the shear stress exerted by the glycerin on the wall of the pipe. Calculate the volume flow rate.