3) Nails are used to connect three boards to form a beam as shown in the figure. Each nail has a shear strength of 400N. The beam is subjected to a vertical shear. Geometrical details are given in the figure. Calculate the allowable shear force for this beam. (Suggested time for solution is 25 minutes) 75mm 75mm 75mm 60 mm 60 mm 120mm 60 mm 200 mm

3) Nails are used to connect three boards to form a beam as shown in the figure. Each nail has a shear strength of 400N. The beam is subjected to a vertical shear. Geometrical details are given in the figure. Calculate the allowable shear force for this beam. (Suggested time for solution is 25 minutes) 75mm 75mm 75mm 60 mm 60 mm 120mm 60 mm 200 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the slope and vertical displacement of point A on the beam shown in the accompanying illustration. Use Conjugate Beam Method. E = 200,000 MPa
Question 1 For the beam and loading shown, using the conjugate method, determine the slope at C in degree measure. Use three decimal places. Express your final answer in absolute value. Assume E = 15,000 MPa and I = 2 x108 mm4.
Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the second moment of area (statical moment of area), Q, of the diamond cross- section at the neutral axis? (in mm3) Write the answer in ordinary notation (e.g. 2100000.65) NOT in scientific notation.
PLEASE REFER TO THE GIVEN VALUES BELOW. For the beam loaded as shown in the figure, determine the following unknowns using ANY GEOMETRIC METHOD Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Round-off to 3 decimal places. a = 8.5 m, b = 3.3 m, c = 9.5 kN/m, d = 27 kN-m. - Slope of the elastic curve at B in degrees. Indicate negative sign as necessary. - Deflection at D in mm. Indicate negative sign if downward. - Deflection at midspan in mm. Indicate negative sign if downward.
Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the second moment of area ( moment of inertia) of the diamond cross? (in mm^4) write the answer in ordinary notation
A built-up section consisting of W 350 x 90 with two 12-mm plates welded to form a box section as shown in the figure. The section is used as a column 10 meters long. Properties of W350x90: b_f = 250 mm t_f = 16.40 mm d = 250 mm t_w = 9.50 mm I_x = 266 x 10^6 mm^4 I_y = 44.54 x 10^6 mm^4 A = 11,550 mm^2 Determine the following: a. Moment of Inertia along X and Y axes. * b. Polar Moment of Inertia with respect to X and Y axes. c. Section Modulus, Sx and Sy d. Radius of Gyration, rx and ry
reply asapp!! Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the first moment of area (statical moment of area), Q, of the diamond cross- section at the neutral axis? (in mm3) Write the answer in ordinary notation (e.g. 2100000.65) NOT in scientific notation.
pls. answer. i'll rate Use virtual work method and determine the following unknowns on the frame shown below.Use I = 800 x 106 mm4 and E = 200 GPa. Show complete and organized solution. Round-off your answersto two decimal places. 1. Solve for the Vertical deflection at point C in mm. 2. Solve for the Horizontal displacement of joint B in mm. 3. Solve for the Slope of at D in degrees. DON'T FORGET THAT THE GIVEN VALUES ARE; a = 36.00 kN/m b = 44.80 kN/m c = 3.70 m d = 7.50 kN/m
For the cross-sectional area of the beam shown in the figure, below: (a) Determine the moments of inertia and product of inertia in relation to the x and y centroid axes;(b) Determine the direction of the main centroidal axes of inertia and the respective moments main inertia;(c) Sketch the corresponding Mohr circle, indicating the results found in items a and b.
A wooden beam is loaded by a distributed load ww = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 3000 mm, LBC = 2000 mm, W=190 mm, B0 = 10 mm, and H = 220 mm, h0=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine a) What is the maximum magnitude of shear force and bending moment, neglecting the sign? Maximum magnitude of shear force, positive value: Maximum magnitude of bending moment, positive value: b) Determine the maximum bending stress and shear stress that occurs in the beam. Maximum bending stress: Maximum shear stress
Please refer to the figure below. Determine R in N at point C.
The basic differential equation of the elastic curve for a cantilever beam is given by thefollowing ODE as:Given L = 120 inches; E = 30,000 ksi; I = 800 in4; P=1 kipInitial Condition: y(0) = 0Solve numerically the ODE for beam deflection y(x) with ∆x = 20 inches, usingEuler’s Method. Write the Euler’s equations for the first two nodes and show yourcomputational work. You can use an Excel file for the rest.Tabulate the results and Plot (x,y).