3) The stress strain relation relationship of the meter stick is shown inthe figure. The meter stick has a 6×25-mm rectangular cross section.Calculate the critical load of the meter stick.a (MPa)140e (mm/mm)0.001

Answered: Image /qna-images/answer/20b96d9b-f384-4c9d-babe-240b8ef9b748.jpg

3) The stress strain relation relationship of the meter stick is shown in the figure. The meter stick has a 6x25-mm rectangular cross section. Calculate the critical load of the meter stick. o (MPa) 140 e (mm/mm) 0.001

3) The stress strain relation relationship of the meter stick is shown in the figure. The meter stick has a 6x25-mm rectangular cross section. Calculate the critical load of the meter stick. o (MPa) 140 e (mm/mm) 0.001

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Related questions

Q: QUESTION 3) Closed and open triangular section tubes are made of same materials are shown in figure.…

A: Given: Closed and open triangular section tubes are made of same materials areshown in figure. If…

Q: Two solid cylindrical rods support a load of P = 27 kN as shown. Rod (1) has a diameter of 17 mm,…

Q: la a- 10 cm 44-4 600 N 14 cm Vertical load is applied to point Bof a 10 mm radius cylindrical bar as…

Q: 100 D P= 400 kN 5. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load…

Q: 1. (A). A 25mm square cross-section bar of length 300mm carries an axial compressive load of 50KN.…

A: as per our guidelines I solved 1st question only

Q: ... - 24 in.-20 in.→ 20 in. 16 in. 8 in.I 8 in. The above figure is a section of a column. If the…

Q: - 25 mm Q: The steel column of circular cross section is attached to rigid supports at A and C.…

Q: The stress–strain diagram for a material can be approximated by the two line segments shown. If a…

A: From the curve, write the expression of the elastic modulus of the material. From the curve, write…

Q: Determine the stress in each section of the bar shown in the Figure when subjected to an axial…

Q: The truss shown in the figure below is made from A992 steel rods having a diameter of 30 mm and…

Q: 1. Determine the stress in each section of the bar shown in the below figure when subjected to a…

Q: 30 30 The cotter shown in the figure is used to fix the squared spigot rod to the plate. The rod is…

A: Given: The diameter of rod, d = 28 mm The yield strength of cotter and the rod, Sy = 280 MPa The…

Q: A pressure vessel containing gas at 250 psi has an outer diameter of 18 inches and a thickness of…

Q: 1.19 For the connection shown in Fig. Pl.19, determine the average shear stress in the 7/8-in.…

Q: The assembly shown in figure (5) consists of two posts AD and CF made of a steel (Ast= 1000 mm2, Est…

Q: A square plate 2 m on each side is supported by four steel tie rods 6-mm-diameter from an overhead…

A: Given data, Side of the square plate, a = 2 m Diameter of the steel rod, d = 6 mm Surface load of…

Q: Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure…

A: Given data: - The yield strength of the pressure vessel is σy = 250 MPa. The pressure acting in…

Q: Compute for the total elongation caused by an axial load of MN kN applied to a bar 20 mm thick…

Q: ick as shown in the ield strength of the 260 N/mm², and plastic moment of nape factor.

Q: 10/10FIND STRESS IN STEEL MATERIALS IN COMPOSITE COLUMIN SHOWN BELOW. IF E st= 200 kN/MM2, Ealu.=70…

Q: Consider two-cylindrical pipes with the loading Pa and PB as shown in the Figure below. The data of…

A: Given DataσA max=300MPaσB max=150MPaFOS=2

Q: eter of wires AB and CB. The allowable tensile stress in each wire is 185 Mpa. 30

Q: A circular steel bar is subjected to various forces as shown in Fig. determine: 1) P 2) The total…

A: Given: A circular steel bar is shown below:

Q: The steel bar has the original dimensions shown in the figure with b = 371 mm and c = 164 mm. If it…

Q: The two plates are joined together using a rectangular pin. What is the smallest width of the plates…

A: given data: applied load (P)=45KN=45*103N dimension of pin=wx15mm allowable shear stress (τs)=120MPa…

Q: QUESTION 1 A Z-section beam of 2 m long and is supported as a cantilever with a 1 kN load at the…

Q: View Policies Current Attempt in Progress A typical stainless steel cylindrical vessel is shown. The…

A: Given data D = 48 in t = 0.75 in P = 1.1 ksi Find Hoop stress = ?

Q: 0.1/The three steel wires shown in Figure 1 are used to support the load. If the wires have an…

A: from equilibrium equation forces are calculated in each wires. F = stress * Area

Q: The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. 10 ft Part A If the wire…

A: Given data: d=0.5 inw=190 lb/ft Need to determine the stretch in the cable.

Q: QUESTION 1) A channel type cross-section is subjected to the compression force P-20 kN at the point…

A: The section is as shown below, The area of the section is, A1=20×5=100 cm2A2=20×5=100…

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: given data dia (d) = 36mm load = 5.20 * 105 N presure (P) = 5.20×105π4×0.0362 allowable stress = σ…

Q: PROBLEM 1. The dimensions of a bar made of a 2024-T6 aluminum alloy and the loads acting on it are…

A: EA1= 73*109pa Let AB is part 1 and BC is part 2 Considering factor of safety 1.5 load acting is…

Q: 1- Calculate the stresses in members CE, DE, and DF. The cross-sectional area of each member is 1200…

Q: Determine the total stress at point A on the cross section a-a in the figure below. 400 kN la -0.5…

A: Draw a diagram showing the neutral axis for the above-cross section.

Q: Q: The aluminum bar of circular cross section is attached to rigid supports at A and C. Calculate…

A: Given data:- D1 =100 mm D2 =50 mm E =70Gpa Force(p) =30KN

Q: The figure shows a bar with a point load of 22 kN applied at the free end, the other end of the bar…

A: Given data: F=22 kNd=6 mm Need to determine the shear stress in the bolt.

Q: The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load…

Q: In the Figure 5, the normal stress on the cross- sectional area is (in Mpa): Figure 5: y P = 400 KN…

A: Area = A = 20 X 30 = 600 mm2 Force normal to area Pn = 400 cos (30) Pn = 346.41 KN

Q: III. A post tapers uniformly from a diameter at the upper end to a larger diameter D at the lower…

A: Upper area is minimum which should be considered.

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: PROBLEM 1 Determine the load that can be applied at the end of the rigid bar if the stress in either…

Q: (2) Q1 what the value of P Which are safer on the rivets as shown in figure below. given that :…

Q: The steel bar has the original dimensions shown in the figure. (Figure 1) It is subjected to an…

A: Given data: F=50 kN Need to determine the change in its length, the new height at section a-a, and…

Q: 1. Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: Fom TL ja- My 10 cm 600 N 14 cm в B Vertical load is applied to point B of a 10 mm radius…

A: Given: Applied load (F)=600NDiameter of the shaft (d)=10mm

Q: Mcq: the maximum shar stress in contact between steel spheres pressed together lies? 1-at the…

A: Ans: 3 is correct. Under the contact surface

Q: The stress–strain diagram of the material can be approximated by the two line segments. If a bar…

A: The stiffness of the column material in the elastic region using stress-strain diagram is calculated…

Q: Question #4 Bar (1) in the figure has a cross-sectional area of 0.75 in². If the normal stress in…

Q: 1. The steel shaft carries the axial loads as shown in the figure below. Determine the change in…

A: Consider the free body diagram:

Question

3) The stress strain relation relationship of the meter stick is shown in
the figure. The meter stick has a 6×25-mm rectangular cross section.
Calculate the critical load of the meter stick.
a (MPa)
140
e (mm/mm)
0.001

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
The copper bar is subjected to a uniform loading shown in Fig. 10–24. Ifit has a length a = 300 mm, width b = 50 mm, and thickness t = 20 mmbefore the load is applied, determine its new length, width, and thicknessafter application of the load. Take Ecu = 120 GPa, ncu = 0.34.
Determine the safe wall thickness of a 50 inches steel tank with internal pressure of 8 Mpa. The ultimate stress is 296 Mpa. The factor of safety to use is 3. A. 2 in B. 3 in C. 5 in D. 4 in
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680 MPa, and for the bronze (σY)br=490 MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa.
A crane hook shown in figure below is made of 30 mm diameter steel rod. The distance between the centroidal axis of the rod and centre of curvature of the hook is 50 mm. Determine the load 'F' so that the maximum stress in the rod is not to exceed 40 N/mm². Proper Answer plz.
The steel bar has the original dimensions shown in the figure. If it is subjected to an axial load of 50 kN, determine the change in its length and its new cross-sectional dimensions at section a–a. Est = 200 GPa, nst = 0.29.
Which of the followings can be found out by calculating the area only under the linear portion (elastic region) and the area under the whole stress strain graph on the same graph? A ) Resillience - Toughness B ) Hardness - Toughness C ) Endurance - Strength D ) Strength - Resillience
Two 300 mm x 120 mm I-section joists are united by 12 mm thick plates as shown in Figure 2 to form a 7 m long stanchion pinned at both ends. Given a factor of safety of 3, a compressive yield stress of 300 MN/m2 and a Rankine constant a= 1/7500, determine the allowable load which can be carried by the stanchion according to the Rankine-Gordon formulae.
A cantilever beam, 100 mm wide by 230 mm high and 7 m long, carries a load that varies uniformly from zero at the free end to 1200 N/m at the wall. Determine the magnitude of the stress in a fiber 60 mm from the top of the beam at a section 4 m from the free end. Answer must be in MPa.
A Steel wire hangs vertically under its weight. What is the greatest length it can have if the allowable tensile stress st =200 MPa, Density of steel g=80 kN/m3.
The member consists of the steel rod AB that is screwed into the end of the bronze rod Find the largest value of P that meets the following design criteria: (a) the overall length of the member is not to change by more than 3 mm; and (b) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of elasticity are 200 GPa for steel and 80 GPa for bronze.
What is the minimum diameter of a bar subjected to an axial load of 6.5 kN if its ultimate stress is 140 MPa 6.34 mm 4.24 mm 7.69 mm 2.43 mm