3) Which of the following statement(s) is/are correct? i. The ability of a material to absorb energy when deformed elastically and to return it when unloaded is called toughness. ii. Modulus of resilience is defined as the strain energy per unit volume required to stress the material from zero stress to the yield stress. i only ii only Both i & ii None of the above

3) Which of the following statement(s) is/are correct? i. The ability of a material to absorb energy when deformed elastically and to return it when unloaded is called toughness. ii. Modulus of resilience is defined as the strain energy per unit volume required to stress the material from zero stress to the yield stress. i only ii only Both i & ii None of the above

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the tensile curves of the following materials, taking into account the appropriate elongation at break, modulus of elasticity and tensile stress, on the side stress-strain graph. a)Low carbon steel (Ecelik=200Gpa),(Syield=300MPa),(Stensile=400MPa) b)High carbon steel (Esteel=200GPa),(Stensile=700MPa) c)Aluminum (Ealuminum=70GPa), (Syield=200MPa),(Stensile=300MPa) d)Cast iron (Ecast iron=120GPa),(Stensile=200MPa)
*Only need Question 10.12 answered. Thank you! 10.11 The elasticity of a cylindrical sample of an unknown material is to be tested. The sample is 40 cm long and has a cross-sectional area of 2.5 cm2 . The sample is hung vertically and a 50 kg weight is attached to its free end. It is found that the sample stretches to a length of 40.1 cm. (a) What is the tensile stress on the sample? (b) What is the tensile strain? (c) What is Young’s modulus for this material? 10.12 (a) Bone has a tensile Young’s modulus of ?tensile = 16 × 109 N m−2 . If the sample of unknown material in Problem 10.11 was replaced with an identical sample of bone, what would the length increase of the bone be? (b) Bone has a compressive Young’s modulus of ?comp = 9 × 109 N m−2 . If the 50 kg weight was used to compress the sample rather than stretch it, how much would the length of the sample change?
21- In which one does the increasing strain rate in response to constant stress occur?A) fully elastic materialB) super plastic materialC) elastic and full plastic materialD) elastic and hardening materialE) semi-plastic material•22- what type of strain causes sprains?A) slipB) don't turnC) pullD) bendingE) pressing•23- Which type of rockwell hardness is suitable for non-ferrous metals?A) BB) EC) AD) CE) D
Which of the following is correct regarding the stress strain curve of Mild steel a. No elastic behaviour b. Higher strains are possible c. the curve is straight d. zero plastic deformation
A cylindrical specimen of aluminum having a diameter of 19 mm (0.75 in.) and length of 200 mm(8.0 in.) is deformed elastically in tension with a force of 48,800 N (11,000 lbf). Using the data inTable 6.1, determine the following:(a) The amount by which this specimen will elongate in the direction of the applied stress.(b) The change in diameter of the specimen. Will the diameter increase or decrease? (Complete Answer, Thank you)
A kind of strain that measures the deformation of a material caused by temperature change a. Shear Strain b. Normal Strain c. Thermal Strain d. None of the above
Mild steel 1 Young;s modulus 1219.5 Yield strain and stress (0.4101,500.08) Failure stress and strain :not able to find because the given data shows the experiment did not reach the failure point. if the material stress and strain does not reach a failure point ,what dose it means , does it means that the material is more stronger?
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 147 kN. - Length of the specimen is 28 mm. - The yield strength is 75 kN/mm2. - The percentage of elongation is 49 %. Determine the following iii) Stress under an elastic load of 16 kN, iv) Young's Modulus if the elongation is 1 mm at 16 kN and (v) Final diameter if the percentage of reduction in area is 22 %. I wont answer for this three questions only: 1)Final Area of the Specimen at Fracture (in mm) 2)Final Diameter of the Specimen after Fracture (in mm) 3)Initial Cross-sectional Area (in mm2)
ENGINEERING QUESTION- SOLVE FROM SCRATCH! A mass of 450 kg has been hung from the end of a metal wire whose initial length is 1.8 meters and is 1.5 mm in diameter. If the wire is stretched 1.25 cm.a) What were the stress and strain?b) What is Young's modulus?
The elastic constant related to direct stress is
Which one(s) of the following about G, shear modulus of elasticity of a material are correct? select all which are correct. G is also called the modules of rigidity. G is related to the modulus of elasticity E and Poisson’s ratio . G is usually smaller than Young's modulus E for the same material. G is the ratio of shear stress to shear strain when the material's proportional limit in shear has not been exceeded.
What is the transformation of strain at a point?