3. A pipe with varying cross-sectional areas is set up vertically as shown in the drawing. Waterenters the pipe from the top wider end at a speed of 300 cm/s. Calculate (a) the mass flow rateof water (the amount of mass entering/exiting the piper every second) and (b) the waterpressure at the bottom narrower end section of the piper. (Density of water is p =1000 kg/m21.00 g/cm'))P 1.20x10 Pa10.0 cmh=4.00 m2.50 cm2P= ?

The solutions to this question can be obtained easily by applying the continuity equations and the…

Answered: 3. A pipe with varying cross-sectional…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reducing bend with an inlet diameter of 200 mm and exit diameter of 150 mm bends 40 degreesupwards. The water velocity and corresponding pressure at the inlet to the band is 4, 5 m/s and 70 kParespectively. Determine the weight flow, the water flow velocity at the exit to the bend, the bend exitpressure if the friction head loss through the bend section is 2 m and the magnitude and direction ofthe resultant force flowing through the bend.
Fluid of constant density is flowing at a velocity of 0.5 meter per second into a horizontal nozzle of decreasing cross-section. The velocity of water ,in meter per second, going out of the nozzle if the diameter at the exit point is 1/3 the diameter in the entry point is
Please show your complete solution. Thank you! Air flows in a steady flow manner through a converging tube. At the inlet the pressure is 690kPaabs and the density is 0.838 kg/cu.m. If air enters with a volume flow of 125 cu.m per min at the rate of 94 m/min and the exit section has a diameter of 350mm, determine a.) the mass flow rate, kg/min b.) the diameter of the entrance section and c.) the exit velocity. Assume that the density is constant.
Water @ 30C and 1atm is flows at a rate of 0.5 m^3/s through a horizontal junction in a pipe. The water exit at the discharge end into the atmosphere. If internal d at the entrance of the junction is 0.3m, while at the exit the d is 0.15m calculate for the resultant force in the junction.
A pump is 2.2 m above the water level in the sump and has a pressure of –20 cm of mercury at the suction side. The suction pipe is of 20 cm diameter and the delivery pipe is short 25 cm diameter pipe ending in a nozzle of 8 cm diameter. If the nozzle is directed vertically upwards at an elevation of 4.2 m above the water sump level, determine the elevation in meters, above the water sump level, to which the jet would reach. Neglect all losses. a.24.04 b.0.10 c.20.31 d.0.52
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
Water at 75 degrees Celsius is flowing horizontally at a rate of 1.6 m^3/min in a pipe. It enters a 3-in 45 degree elbow and is diverted upwards into a connecting pipe. The diameter of the outlet is 2in. If the pressure just before the elbow is 78 kPa, determine the magnitude and direction of the force necessary to keep the elbow in place. Assume frictional losses in the elbow are negligible.
A hydroelectric power plant uses Pelton-type turbines, in which multiple nozzles are used to accelerate the waterwhich is directed onto the turbine blades, which are exposed to an atmospheric pressure of 101.325 kPa. The water enters the nozzles with an absolute pressure of 500 kPa and a speed of 5 m/s, and the nozzle outlets are exposed to atmospheric pressure and have an internal diameter of 5 cm. Consider that the specific mass of water is 1,000 kg/m3. Determine the mass flow rate of water through each of the nozzles, and explain why the actual mass flow rate will be lower.
Which fluid at room temperature requires a larger pump to flow at a specified velocity in a given pipe: water or engine oil? Why?
Air at 20oC (density = 1.204 kg/m3) flows towards a rotating cylinder of diameter 1.50 m. If the velocity of the air is 100 km/h and the cylinder rotates clockwise at 220 rpm, determine (c) the maximum velocity of the air around the rotor, and (d) the pressure coefficient at the location corresponding to the maximum velocity.
In a pipe conveying steady flow of incompressible fluid, what factor determines the magnitude of flow velocity? O Friction O Temperature © Cross-sectional area
A pipe line of length 2000 m is used for power transmission. If 110 kW power is to be transmitted through the pipe in which water having a pressure of 490.5 N/cm2at inlet is flowing. If the pressure drop over the length of pipe is 98.1 N/cm2and ff = 0.0065.Determine:The diameter of the pipe and the volume flow rate; and If a nozzle is introduced at the end of the pipe, what would be its diameter and the power transmitted.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS