3. A plate is held against a horizontal water jet in the horizontal plane as shown. The jet has a diameter of 30 mm and an unknown velocity. A force of 200 N is required to hold the plate in the position. Determine the velocity of flow of the jet just before it hits the plate. What is the discharge? <<-200 N

3. A plate is held against a horizontal water jet in the horizontal plane as shown. The jet has a diameter of 30 mm and an unknown velocity. A force of 200 N is required to hold the plate in the position. Determine the velocity of flow of the jet just before it hits the plate. What is the discharge? <<-200 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A block weighing 100 kN is pushed by a horizontal force of 100 kN along a smooth horizontal plane from A to B,10 m distant. The velocity of the block at A is 10m/s. The block is released at B and passes through an upward circular arcBC (tangent to B) of radius 10m and central angle 45 degrees and along an inclined plane CD tangent to the arc at C.Required: Sketch the given conditions and draw the necessary FBDs. Then determine the following:a. the velocity of the block at B.b. the velocity of the block at C.c. the distance along CD that the block will move before it comes to rest.
Please Answer it fast on Sheet of paper. F1=1.5KN ,F2=3.8KN, a=3.6m ,b=2.0m ,c=1.3m. You need to find Forces in member (CH,AH and CD) And whether it's +ve or -ve.
Determine the pressure at A choices are: A. 7.488 Kpa B. 7.848 kPa C. -7.848 kPa D. -7.488 kPa Determine the pressure at C choices are: A. 4.905 kPa B. -4.905 kPa C. 4.950 kPa D. -4.950 kPa Determine the pressure at D choices are: A. 19.35 kPa B. 20.35 kPa C. 21.68 kPa D. 17.94 kPa
Fluid mechanics, i need solutions in 10 minutes please. MCQ/ Based on question 2, what is the horizontal component of the hydrostatic force of the water on the panel? A-448.029 kN B-434.282 KN C- 389.185 KN D-471.457 KN E- 354.974 KN F-420.415 kN G-504.986 KN H-318.464 KN I-336.659 KN J- 372.075 KN K-459.601 KN L-490.211 KN M-480.529 KN N-404.792 KN
The elasticity and dimension of a pipe are such that the celerity of pressure wave is 975 m/s. The pipe diameter is 1.2m and a valve is located 600 m downstream. Water is flowing initially at 0.85 m³/s. 1. Find the water hammer pressure for instantaneous valve closure. a. 721.35 kPa b. 753.12 kPa c. 731.25 kPa d. 712.53 kPa 2. What is the approximate water hammer pressure if the valve is closed in 4 seconds? a. 522 kPa b. 235 kPa c. 225 kPa d. 125 kPa 3. What is the water-hammer pressure if the valve is manipulated so that the flow rate drops almost instantly from 0.85 to 0.28m³/s? a. 487.5 kPa b. 458.7 kPa c. 496.2 kPa d. 425.8 kPa
Fluid mechanics, I need solutions in 15 minutes please. MCQ/Determine the magnitude of the force acting on the gate due to oil pressure. A-235.312 kN B-252.964 kN C- 209.223 KN D-166.781 KN E-215.487 KN F-174.214 KN G-221.578 KN H-189.872 KN I-194.666 KN J-150.114 KN
Determine: 2Z1 + 5Z2 show solutions with steps asap
Fluid mechanics , i need solutions in 15 minutes please. MCQ/If the shape of the gate is square with the dimensions of 3 mx 3 m, determine the magnitude of the force acting on the gate due to oil pressure . A-210.254 KN B-570.896 KN C-280.988 KN D- 623.224 KN E- 456.037 kN F-828.093 KN G- 348.581 KN H-710.226 KN I-694.447 KN J- 777.001 KN
Piston A has a cross-section of 1200 cm^2 while that of B is 800 cm^2. B is higher than A by 2m. If the intervening passages are filled with oil having s.g. of 0.8 and a force of 4 kN is acting on BWhat must be the pressure at piston B choices are: A. 50 kPa B. 60 kPa C. 70 kPa D. 80 kPa What must be the pressure at piston A choices are: A. 56.70 kPa B. 65.70 kPa C. 66.70 kPa D. 65.50 kPa What must be the force exerted at piston A choices are: A. 7.98 kN B. 7.78 kN C. 7.81 kN D. 7.88 kN
What pipe material will result in a friction factor of f = 0.014 for a 180 m long, 0.2 m diameter pipe flowing hot water at 0.11 m3/s? Kinematic Viscosity of hot water is 2.3x10-7 m2/s, Choose one: Drawn Tubing with k = 0.001 mm Commercial Steel with k = 0.04 mm Riveted Steel with k = 1 mm Concrete with k = 0.2 mm
Rectangular load C to D = 200lb/ft
Hydraulic Toolbox 3