Control charts for x and R are maintained on a process. After 20preliminary subgroups each of size 3 are evaluated, you have the following data:3.2020Ex, = 5,502ER, = 60a. Set up the control charts using these data.b. Assume that the process exhibits statistical control. Estimate the process meanand standard deviation.c. Suppose that the quality characteristic is normally distributed with specificationsat 275 = 6. Estimate the fraction nonconforming produced by this process.

ANSWER A : R-Chart: X-bar chart:

Answered: 3. Control charts for x and R are…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

An automatic filling machine is used to fill 1-liter bottles of cola. The machine’s output is approximately normal with a mean of 1.0 liter and a standard deviation of .01 liter. Output is monitoredusing means of samples of 25 observations.a. Determine upper and lower control limits that will include roughly 97 percent of the samplemeans when the process is in control.b. Given these sample means: 1.005, 1.001, .998, 1.002, .995, and .999, is the process in control?
Resistors for electronic circuits are manufactured on a high-speed automated machine. The machine is set up to produce a large run of resistors of 1,000 Ohms each. To set up the machine and to create a control chart to be used throughout the run, 15 samples and their measured values are as follows: Sample Number Readings (in Ohms) 1 1010 991 985 986 2 995 996 1009 994 3 990 1003 1015 1008 4 1015 1020 1009 998 5 1013 1019 1005 993 6 994 1001 994 1005 7 989 992 982 1020 8 1001 986 996 996 9 1006 989 1005 1007 10 992 1007 1006 979 11 996 1006 997 989 12 1019 996 991 1011 13 981 991 989 1003 14 999 993 988 984 15 1013 1002 1005 992 Develop three-sigma appropriate control chart(s) from the chart(s) what comments can you make about the process? Explain and show work
State True or False for the below two statements. 1. The purpose of process control charts is to detect the presence of natural variations. 2. Unlike process capability ratio (Cp), process capability index (Cpk) can possibly be negative.
When a robot welder is functioning properly the cylinders it produces burst (on average) at 3400 psi, with known standard deviation 100 psi. Determine the 3-Sigma mean control chart limits. Test lot sample sizes are n=4 cylinders randomly selected from the production line. a. Centerline = ____ b. Upper Limit = ____ c. Lower Limit = ____ d. What is the probability that random variation will exceed the ± 3-sigma limits ____. (four decimal places with zero before the decimal)
Suppose that a processoutput is normally distributed with a mean of 30.0 and a variance of 1.44. If the specifications are 30.0 /- 3.25, then compute process capability indices. Is the process capable of meeting specifications?
Refer to the table Factors for Computing Control Chart Limits (3 sigma) LOADING... for this problem. Your supervisor, Lisa Lehmann, has asked that you report on the output of a machine on the factory floor. This machine is supposed to be producing optical lenses with a mean weight of 50 grams and a range of 3.5 grams. The following table contains the data for a sample size of n=6 taken during the past 3 hours: Sample 1 2 3 4 5 6 7 8 9 10 x 55 47 49 50 52 57 55 48 51 56 R 3 1 5 3 2 6 3 2 2 3 Part 2 Set the control limits for this process for the x-chart when the machine is working properly. a) What are the x overbar-chart control limits when the machine is working properly? Calculate the upper control limit of the x overbar-chart Calculate the…
The central limit theorem:a) is the theoretical foundation of the c -chart.b) states that the average of assignable variations is zero.c) allows managers to use the normal distribution as thebasis for building some control charts.d) states that the average range can be used as a proxy forthe standard deviation.e) controls the steepness of an operating characteristiccurve.
A manufacturer is selling pharmaceuticals that have a weight specification 199.8 to 200.2 mg, with a target value of 200 mg. Before sending its next shipment, the company collects a large sample of product and determines the mean weight of the sample is 199.89 mg, with a standard deviation of 0.035 mg. The process capability index for the current process is ____. Round to three decimal places.
(CO 3) The soup produced by a company has a salt level that is normally distributed with a mean of 5.4 grams and a standard deviation of 0.3 grams. The company takes readings of every 10th bar off the production line. The reading points are 5.8, 5.9, 4.9, 5.2, 5.0, 4.9, 6.2, 5.1, 6.7, 6.1. Is the process in control or out of control and why? Group of answer choices It is out of control as one of these data points is more than 3 standard deviations from the mean It is in control as the data points more than 2 standard deviations from the mean are far apart It is in control as the values jump above and below the mean It is out of control as two of these data points are more than 2 standard deviations from the mean
Using samples of 200 credit card statements, an auditor found the following:Sample 1 2 3 4Number with errors 4 2 5 9a. Determine the fraction defective in each sample.b. If the true fraction defective for this process is unknown, what is your estimate of it?c. What is your estimate of the mean and standard deviation of the sampling distribution of fractions defective for samples of this size?d. What control limits would give an alpha risk of .03 for this process?e. What alpha risk would control limits of .047 and .003 provide?f. Using control limits of .047 and .003, is the process in control?g. Suppose that the long-term fraction defective of the process is known to be 2 percent. What arethe values of the mean and standard deviation of the sampling distribution?h. Construct a control chart for the process, assuming a fraction defective of 2 percent, using twosigma control limits. Is the process in control?
Which of the following statements is NOT true about the process capability ratio? a. The process capability ratio is a ratio for determining whether a process meets design specifications. b. The process capability ratio is computed as the difference of the upper and lower specification limits divided by six standard deviations. c. The process capability ratio is a ratio of the specification to the process variation. d. A capable process has a process capability ratio less than one.
When plotting a process, with the intention of monitoring trends, which of the following apply? Select one: a. An increase in the mean and a decrease in variation is desirable b. A decrease in both the mean and variation is desirable c. The optimum mean may be lower or higher than current values d. The mean is not as important as the variation

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS