3. Sketch a pressure-volume diagram for steam and mark on it the following points, labelling clearly the pressure, specific volume and temperature of each point a. T= 212.4 °C, v=0.09957 m³/kg b. P= 10 bar, h= 2650 kJ/kg c. P= 6 bar, h= 3166 kJ/kg 4. Calculate the internal energy for each of the four stages given in Problem no. 3

3. Sketch a pressure-volume diagram for steam and mark on it the following points, labelling clearly the pressure, specific volume and temperature of each point a. T= 212.4 °C, v=0.09957 m³/kg b. P= 10 bar, h= 2650 kJ/kg c. P= 6 bar, h= 3166 kJ/kg 4. Calculate the internal energy for each of the four stages given in Problem no. 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

With a flow rate of 50 kmol/hour, air is compressed from P 1 = 1.2 bar pressure to P 2 = 6 bar pressure. The power required for this process is 98.8 kW. Temperature and speed data are given below. T1 = 300 K ,T 2 = 520 K ,v1 = 10 m/s, v2 = 3.5 m/s What is the heat rate transferred to the compressor (kJ/s)? Assume that air has Cp = (7/2)R and enthalpy is independent of pressure. (Gpt/Ai wrong ans not allowed)
In a three-stage compressor, the pressure ratio in each stage is equal and its value is 1.3, the first inlet temperature to stage 300K, outlet pressure from first stage 1000mmHg, , Polytropic yield 0.92. m C1 C2 = C2s C3 C3s = 500 "It s Isentropic exponent=1.4, coefficient of heating heat under constant pressure= 1005 kgK' your mercury density= 13550 and gravitational acceleration= 9.81 m3 m3 a) Find the actual and isentropic temperature of the exit from the 1st stage. b) Find the actual and isentropic temperatures of the exit temperatures from the 2nd stage. c) Find the real and isentropic work consumed in Stage 2. d) Put the available data and your calculations in the compressor (h-s) diagram.
Steam enters a convergent-divergent nozzle at 11 bar, dry saturated at a rate of 0.75 kg/sand expands isentropically to 2.7 bar. Neglecting the inlet velocity, and assuming theexpansion follows a law, pv1.135 = constant, calculate the area of the nozzle throat and thearea of the nozzle exit.
A turbine is driven by a system that enters the turbine at the ff. conditions: 500 kg/h, 44 atm, 450 deg C, 60 m/s linear speed. The steam exits at a point five meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 360 m/s speed. 70,000 W of shaft work is delivered by the turbine while 104 kilocalories/h heat is lost. Why is expansion work 0 and why cannot the flow work be calculated?
A four-stage compressor works between limits of 1 bar and 120 bar. The indexof compression in each stage is 1.25, the temperature at the start ofcompression in each stage is 30 ˚C, and the intermediate pressure areselected such that work is divided equally among the stages. If the clearanceis negligible: Calculate: 1. the volume of free air delivered per kilowatt-hour at 1.013 bar and 20 ˚C2. isothermal work input 3. isothermal efficiency.
An ideal gas flows adiabatically through a duct. At section1, p1 =140 kPa, T1 = 2608C, and V1 = 75 m/s. Fartherdownstream, p2 = 30 kPa and T2 = 2078C. Calculate V2 inm/s and s2 - s1 in J/(kg ? K) if the gas is (a) air, k = 1.4,and (b) argon, k = 1.67.
Four pounds of air gain 0.491 Btu/R of entropy during a nonflow isothermal process. If p1=120 psia and V2=42.5 ft3, find (a)V1 and T1, (b) W, (c) Q and (d) change of internal energy.
Air flows steadily through an engine at constant temperature, 127 deg C. Assuming that the Kinetic and Potential energies are negligible and if the exit pressure is one-fourth of the initial pressure, in which the initial pressure is 702 kPa, the work per mass is Answer kJ (nearest whole number).
A turbine is driven by a system that enters the turbine at the ff. conditions: 200 kg/h, 39 atm, 501 deg C, 49 m/s linear speed. The steam exits at a point 8 meters below the inlet stream of the turbine with the following conditions: atmospheric pressure, 290 m/s speed. 69000 W of shft work is delivered by the turbine while 100 kcal/h heat is lost. What is the value of (a) expansion work and (b) flow work? If the value is zero, explain why is it so.If it cannot be calculated, explain why.
For a nozzle-duct system shown in Fig.Q3, the nozzle is designed to produce a Mach number of 2.8 with y = 1.4. The inlet conditions are po1 = 10 bar and To1 = 370 K. The duct is 8 diameters in length, but the duct friction factor is unknown. The receiver pressure is fixed at 3 bar and a normal shock has formed at the duct exit. (a) Determine the friction factor of the duct. (b) What is the total change in entropy for the system? 10 bar 3 ber T- 370 K Pne Ar 8D- Fig.Q3
8.. Nitrogen gas is compressed . Pressure rises from 100 kPa to 1500 kPa. Initial temperature of 25 deg C. The required mass flow is 1000 kg/hr. Would you recommend single stage or multi-stage compression? Justify your recommendation with appropriate calculations. For Nitrogen, R = 0.297 kJ/ kg K, g = 1.4, r = 1.25kg/m3, µ = 17.4 µPa s, cp = 1.039 kJ/kg K
Complete the table below. Show your solutions and draw the corresponding T-s diagram for each case Pressure, kPa Temperature, oC Specific volume, m3 Internal energy, kJ/kg Enthalpy, kJ/kg Entropy, kJ/kg-K Steam Quality, % Steam Condition 2000 90 250 2750 40000 600