3. The results of a simple calibration of pressure transducer and its specification are shown in Figure 1 and Table 1. The sensitivity of the pressure sensor is 0.5 V/kPa (given by manufacturer) and the linear curve fit for the upscale calibration is given as y = 0.51x + 0.02 . a) Calculate the hysteresis and linearity errors for this calibration. b) Please discuss either the pressure transducer can now be used for the actual measurement or not. Table 1: Pressure tansducer specification Operation Input range 0- 5 kPa + 15 V 0- 2.5 V Excitation Output range Performance Linearity error + 3 % Hysteresis Less than + 15% + 5% Sensitivity error Thermal sensitivity error + 0.02% / °C Temperature range 0 – 50 °C upecate mesuremen 2 1.5 bounscae mesrement 0.5 35 pressure, Pa Input, pressure Ouput, voltage (V) (kPa) Upscale Downscale 0.00 0.00 1 0.53 0.48 2 1.05 0.94 3 1.62 1.45 4 2.12 1.95 2.50 2.50 Figure 1: Calibration results (plot and tabulated data)

3. The results of a simple calibration of pressure transducer and its specification are shown in Figure 1 and Table 1. The sensitivity of the pressure sensor is 0.5 V/kPa (given by manufacturer) and the linear curve fit for the upscale calibration is given as y = 0.51x + 0.02 . a) Calculate the hysteresis and linearity errors for this calibration. b) Please discuss either the pressure transducer can now be used for the actual measurement or not. Table 1: Pressure tansducer specification Operation Input range 0- 5 kPa + 15 V 0- 2.5 V Excitation Output range Performance Linearity error + 3 % Hysteresis Less than + 15% + 5% Sensitivity error Thermal sensitivity error + 0.02% / °C Temperature range 0 – 50 °C upecate mesuremen 2 1.5 bounscae mesrement 0.5 35 pressure, Pa Input, pressure Ouput, voltage (V) (kPa) Upscale Downscale 0.00 0.00 1 0.53 0.48 2 1.05 0.94 3 1.62 1.45 4 2.12 1.95 2.50 2.50 Figure 1: Calibration results (plot and tabulated data)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

We wish to measure a characteristic of a machined part whose nominal size is 50 mm at 20 °C. For this, two different instruments are used; an analog micrometer and a digital vernier caliper, both recently calibrated and with the same resolution (0.01 mm). The calibration certificate data of the analog micrometer and the digital vernier are shown in tables 5 and 6 respectively. In both cases the calibration uncertainty does not include the contribution of resolution uncertainty. Additionally, there are drift studies for both instruments and it is established that the drift of the micrometer is ± 0.002 mm while the drift of the vernier is ± 0.02 mm. The same number of measurements were performed with both instruments to avoid repeatability biases under controlled environmental conditions. Table 7 shows the results of the measurements of both instruments. The temperature of the piece was monitored with a digital thermometer whose calibration uncertainty is 0.1 °C, which already includes…
A signal is made up of 3 sine waves of equal amplitude with frequencies F1 = 180 hz, F2 = 1200 Hz, and F3 = 2500 Hz. This signal is monitored using a DAQ and plotted on a FFT. The DAQ settings are Fsample = 4000 Hz, Nsample = 10,000. 1). Draw the resulting measured FFT below. 2). Draw the resulting measured FFT if the signal is passed through an analog Low Pass filter with a cutoff frequency of Fc = 400 Hz prior to measurement.
A displacement transducer has the following specifications: Linearity error: ±0.25% reading Drift: ±0.05%/°C reading Sensitivity error: ±0.25% reading Excitation: 10-25 V dc Output: 0-5Vdc Range: 0-5 cm The transducer output is to be indicated on a voltmeter having a stated accuracy of 0:1% reading with a resolution of 10 μV. The system is to be used at room temperature, which can vary by 10 °C. Assume 95% confidence. The displacement transducer above is used in measuring the displacement of a body impacted by a mass. Twenty measurements are made, which yield Determine a best estimate for the mass displacement at 95% probability based on all available information.
PLS ANSWER ASAP. THANK YOU! The slope of the calibration curve is based on __________. a. calibration limit b. calibration sensitivity c. calibration detection d. calibration function
Discuss the importance of measuring devices for Electric Motor and Internal Combustion Engine in terms of accuracy.
The following applies to a second-order mechanical underdamped measurement system: a. It has instantaneous transient response. b. Settling time is an important parameter c. Effects of capacitance and inductance must be considered. d. Time constant τ is the only important characteristic of the response.
a) Describe static sensitivity and time constant of instrument?b) A thermometer having a time constant of 1 min is initially at 50 oC. It is immersedin a bath maintained at 100 oC at time = 0. Express temperature in oC at time = 1.2min
n a certain dynamic measurement application the input(x) – output(y) relationship is given by y=1+(1+x)e^(-x) With what uncertainty must x be determined to yield a relative uncertainty of ±5 percent for y at a value of x = 2,4
A force measurement system (weight scale) has the following specifications as shown in Table 1: Estimate the overall instrument uncertainty for this system based on available information. FSO refers to full-scale operating range.
1- Change in temperature is a physical input variable of a sensor. Select one: True False
Instrumentation & Measurements This homework measures your capability to design/analyze various components/variables of ameasurement system based on what you have studied. Question 1 Attached.
The ability of the instrument to give same output for same input when the conditions are different is known as __________________ a. Repeatability b. Resolution c. Reproducibility d. Accuracy