3. Two batteries, = 6 V, 0.25 , and = 12 V, 0.5 2 are connected series-opposing. An external resistance of 5.25 is connected across their terminals. Determine: a. The total supply current b. The terminal voltage of the first battery c. The terminal voltage of the second battery d. The terminal voltage of the 2 batteries in series

3. Two batteries, = 6 V, 0.25 , and = 12 V, 0.5 2 are connected series-opposing. An external resistance of 5.25 is connected across their terminals. Determine: a. The total supply current b. The terminal voltage of the first battery c. The terminal voltage of the second battery d. The terminal voltage of the 2 batteries in series

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter21: Circuits And Dc Instruments

Section: Chapter Questions

Problem 51PE: Suppose you measure the terminal voltage of a 3.2G0-V lithium cell having an internal resistance of...

See similar textbooks

Similar questions

Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
The IR drop across a resistor means that there is a change in potential or voltage across the resistor. Is there any change in current as it passes through a resistor? Explain.
If two different wires having identical cross-sectional areas carry the same current, will the drift velocity be higher or lower in the better conductor? Explain in terms of the equation vd=1nqA by considering how the density of charge carriers n srelates to whether or not a material is a good conductor.
How does the resistance for copper and for silicon change with temperature? Why are the behaviors of these two materials different?
Unreasonable Results A 1.58-V alkaline cell with a 0.200- internal resistance is supplying 8.50 A to a load, {a) What is its terminal voltage? (b) What is the value of the load resistance? (c) What is unreasonable about these results? (d) Which assumptions are unreasonable or inconsistent?
A homemade capacitor is constructed of 2 sheets of aluminum foil with an area of 2.00 square meters, separated by paper, 0.05 mm thick, of the same area and a dielectric constant of 3.7. The homemade capacitor is connected in series with a 100,00- resistor, a switch, and a 6.00-V voltage source, (a) What is the RC time constant of the circuit? (b) What is the initial current through the circuit, when the switch is closed? (c) How long does it take the current to reach one third of its initial value?
What are the advantages and disadvantages of connecting batteries in series? In parallel?
Suppose you measure the terminal voltage of a 3.2G0-V lithium cell having an internal resistance of 5.00 by placing a 1.00-k voltmeter across its terminals, (a) What current flows? (b) Find the terminal voltage, (c) To see how close the measured terminal voltage is to the emf, calculate their ratio.
Currents of approximately 0.06 A can be potentially fatal. Currents in that range can make the heart fibrillate (beat in an uncontrolled manner). The resistance of a dry human body can be approximately 100 k . (a) What voltage can cause 0.06 A through a dry human body? (b) When a human body is wet, the resistance can fall to 100 . What voltage can cause harm to a wet body?
When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T T0)] (Eq. 17.7), where is the temperature coefficient of resistivity. (a) Show that a more precise result, which includes the length and area of a wire change when it is heated, is R=R0[1+(TT0)][1+(TT0)][1+2(TT0)] where is the coefficient of linear expansion. (See Topic 10.) (b) Compare the two results for a 2.00-m-long copper wire of radius 0.100 mm, starting at 20.0C and heated to 100.0C.
A 120-V immersion heater consists of a coil of wire that is placed in a cup to boil the water. The heater can boil one cup of 20.00°C water in 180.00 seconds. You buy one to use in your dorm room, but you are worried that you will overload the circuit and nip the 15.00-A, 120-V circuit breaker, which supplies your dorm room. In your dorm room, you have four 100.00-W incandescent lamps and a 1500.00-W space heater, (a) What is the power rating of the immersion heater? (b) Will it trip the breaker when everything is turned on? (c) If it you replace the incandescent bulbs with 18.00-W LED, will the breaker nip when everything is turned on?
Three identical 60.0-W, 120-V lightbulbs are connected across a 120-V power source as shown in Figure P28.72. Assuming the resistance of each lightbulb is constant (even though in reality the resistance might increase markedly with current), find (a) the total power supplied by the power source and (b) the potential difference across each lightbulb.