I need the answer as soon as possible 4-18- A 15-hp, 220-V, three-phase, 60-Hz, 6-pole, Y-connectedinduction motor has the following parameters per phase:ri = 0.128 2Xi +X'2= 0.496 Qŕ2 = 0.0935re = 183 QX, =8 Qthe rotational losses are equal to the stator hysteresis and eddy-current losses For a slip of 3%, find:(a) The line current and power factor.(b) The horsepower output(c) The starting torque.

Answered: Image /qna-images/answer/e1c22d7f-c24f-49cd-af6c-0e7b31720479.jpg

Answered: 4-18- A 15-hp, 220-V, three-phase,…

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter31: Wound Rotor Motors

Section: Chapter Questions

Problem 10RQ

See similar textbooks

Similar questions

A 3-phase, 50 Hz, 3000 V motor develops 600 H.P. (447·6 kW), the power factor being 0·75 lagging andthe efficiency 0·93. A bank of capacitors is connected in delta across the supply terminals and powerfactor raised to 0·95 lagging. Each of the capacitance units is built of five similar 600-V capacitors.Determine the capacitance of each capacitor.
A 250-V, 4-pole, wave-wound d.c. series motor has 782 conductors on itsarmature. It has armature and series field resistance of 0.75 ohm. The motor takesa current of 40 A. Estimate its speed and gross torque developed if it has a flux per pole of 25 mWb
In a no-load motor, a constant electromagnetic torque of 5 Nm is generated at t = 0. The engine reached 1800 revs in 4 seconds. Calculate motor inertia ignoring friction.
23.) A 5-in.3 displacement motor is to be tested on a bench at 3000 rpm at 2500 lbf/in2. Assuming 100% efficiency , estimate the FHP output of the motor?
Example 34.2. The stator of a 3-0 induction motor has 3 slots per pole per phase. If supply Jrequency is 50 Hz, calculate (i) number of stator poles produced and total number of slots on the stator (i) speed of the rotating stator flux (or magnetic field).
A motor running 1800rpm transmits 10KW of power through a 25mm diameter shaft 1.2m long. What is the angle of twist in the shaft? G=8.3x10^10 Pa. A)1.14 degree B)1.59 degree C)1.34 degree D)1.04 degree
why the overdamped curve lies above the critically damped one and approaches zero at slower rate?
What is the purpose of the Tip Mass in the model of the Magnetostrictive vibration energy harvester?
4. A roller chain is to transmit 38.5 hp from a splitphase motor, turning 650 rpm, to a reciprocatingpump, turning at 200 rpm. The system useschain#100 with smaller sprocket having 21 teeth.Assuming a service factor of 1.6 using C = D2 + D1/2,determine (a) the rated horse power of the chain, (b)number of teeth of the larger sprocket, (c) the pitchlength of the chain, and (d) the number of strandsrequired. Express your answer in 3 decimal place.
A Solid steel shaft running at 600rpm is supported on bearings 600mm apart. The shaft receives 40kW through a 400mm diameter pulley weighing 400N located 300mm to the right of left bearing by a vertical flat belt drive. The power is transmitted from the shaft through another pulley of diameter 600mm weighing 600N located 200mm to the right of right bearing. The belt drives are at right angles to each other and ratio of belt tensions is 3. Determine the size of the shaft necessary, if the allowable shear stress in the shaft material is 40MPa and the loads are steady.
if you wrong i will dislike. A motor driving a solid circular steel shaft transmits 40 kW of power at 500 rpm. If the diameter of the shaft is 40 mm, the maximum shear stress in the shaft is
Define the Spring Work by a differential?

SEE MORE QUESTIONS

Recommended textbooks for you

Understanding Motor Controls

Mechanical Engineering

ISBN:

9781337798686

Author:

Stephen L. Herman

Publisher:

Delmar Cengage Learning

Electrical Transformers and Rotating Machines

Mechanical Engineering

ISBN:

9781305494817

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Understanding Motor Controls

Mechanical Engineering

ISBN:

9781337798686

Author:

Stephen L. Herman

Publisher:

Delmar Cengage Learning

Electrical Transformers and Rotating Machines

Mechanical Engineering

ISBN:

9781305494817

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS