4. A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630 in steel wire, which is 10 inches long? Assume deformation to be vertical. Use E = 30 x 10® psi. 4.5 in 2 in. Steel wire а. 0.0481 с. 0.0581 b. 0.0531 d. 0.0631 P.

4. A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630 in steel wire, which is 10 inches long? Assume deformation to be vertical. Use E = 30 x 10® psi. 4.5 in 2 in. Steel wire а. 0.0481 с. 0.0581 b. 0.0531 d. 0.0631 P.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.4P: Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield...

See similar textbooks

Related questions

Q: 8.4 To determine the strength of the riveted joints in a cylindrical vessel, tensile tests were…

A: Given Width = 6 in Longitudinal force = 32 kips Circumferential force = 16 kips Pressure = 150 psi…

Q: 7. A steel 0.6 inch x 1.2 inch steel 90 m long is subjected to a 45kN tensile load along its length.…

A: A material elongates in the axial direction while contracting in the transverse direction when…

Q: circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; V = 0.33] pipe has an outside diameter of…

A: Given:Youngs modulus, E=70 GPaThermal coefficient, α=22.5*10-6/°CV=0.33Outside diameter, D=225…

Q: 8. A rigid bar AB is supported by three rods. A load P = 275 kN is applied to %3D the bar. The…

Q: True strain for a steel bar which is doubled length by tension is : (a) 0.307 (b) 0.5

A: LetInitial length of bar is L0

Q: 09:A tensile stress is to be applied along the long axis of a cylindrical brass rod that has…

Q: 2. Determine the deformation of the steel rod shown in Fig. 2 under the given loads (E=29x10 psi).…

Q: 5 (a) A steel bar is subjected to a sequence of completely reversed stress cycles which vary over a…

A: Given , Endurance Limit(Se) = 430 N/mm2 Completely reversed stress cycle, S1 = 570 N/mm2 S2 = 630…

Q: A copper specimen of Young's Modulus 129 GPa is subjected to a tensile test in a laboratory and the…

A: Given data The initial length of specimen (Li) = 396 mm The initial diameter of the specimen (Di) =…

Q: A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of…

Q: 2.47 The rigid block of mass M is supported by the three symmetrically placed rods. The ends of the…

A: To find : The largest allowable value of M. Given : The length of copper rod is lcu=160 mm. The…

Q: 3. If the ultimate shear strength of steel plate is 45,000 psi, what force is necessary to punch a…

A: Given data:

Q: A tensile test specimen has a gage length = 3.0 in and diameter 0.75 in. Yielding occurs at a load…

A: In order to determine the tensile strength of the specimen, the maximum load and area of cross…

Q: A cylindrical specimen of a steel alloy having a diameter of 12.8 mm and a gauge length of 50.8 mm…

A: Given dataFOS=2.5F=8230 NTo find the shank diameterof SQeW

Q: The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than…

A: GivenAc=2.78 in2Aal=3.28in2Ec=17013025 ksiEal=10072240…

Q: A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630 in…

Q: QUESTION 2 A connecting link, 160mm in length, is 50mm in diameter for a length of 100mm and 30mm in…

Q: A Brinell hardness measurement of 650 HBN, using a 10-mm-diameter indenter and a 2950 kg load on an…

Q: A 16-mm-diameter steel [E= 200 GPa] rod (2) is connected to a 50-mm-wide by 8-mm-thick rectangular…

A: The elongation of member when subjected to a longitudinal force is calculated using the formula…

Q: 2. A mild steel rod 1 m long and 20 mm diameter is subjected to an axial pull of 62.5 kN. What is…

A: Given data: - The length of the steel rod is L = 1 m. The diameter of the rod is d = 20 mm. The…

Q: A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of…

Q: Q1. A bracket, as shown in Fig. is supported by 5 bolts, two at the bottom and three above.…

A: To find: The size of bolts. Given: The factor of safety is FOS=2. The number of bolts n=5. The yield…

Q: The riveted lap connection shown consists of two(2) – PL 12 mm × 280 mm. 1. If allowable shearing…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: 4. A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630…

Q: A bar of dimension 130 mm x 50 mm x 45 mm, is subjected to an axial pull of 90 kN. The measured…

Q: A rope 3.5 mm² breaks when a load of 50 kN is applied to it. Estimate the diameter of the same rope…

Q: (1) A tensile stress is to be applied along the long axis of a cylindrical brass rod that has a…

A: Solution of problem-1: The data given is,

Q: Determine the deformation of the steel rod (E = 29 x 106 psi). shown in Fig. 4. The cross-sectional…

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in ension. An axial load…

Q: The lap joint shown supports a weight W equal to 300 lb. The bearing stress and the shear stress…

A: Given data: weight = 300 lb Bearing stress = 18 ksi = 18000 lb/in2 Shear stress = 9 ksi = 9000…

Q: In a standard tensile test a steel rod of 7/8 in. in diameter is subjected to a tension force of 17…

A: given data - v= 0.25 to determine - ratio of G/D

Q: 100 N K 250 N 200 N 50 N No 500 mm 400 mm 1700 mm

A: Given; E=200 GPa=200000 MPaA =25 mm2

Q: Solve the following problems, complete with free body diagrams, clear solutions, and complete final…

A: To determine the average normal stress in the rods 1 and 2.

Q: A 300 mm rod is subjected to 4 kN of tensile force. The allowable stress and deformation is 60 MPa…

Q: If the steel rod shown is acted upon as shown, Compute for the total deformation of the rod. Assume…

Q: A bar of 12 mm diameter gets stretched by 3 mm under a steady load of 8 kN. What stress would be…

Q: (3X) A stress-strain diagram for a tension test of an alloy steel sample is shown in the diagram…

A: Stress-Strain curve gives the idea of the material to carry a load or the behaviour of the material…

Q: 1. A rod will be selected to support a tensile load of 74 kN. If the allowable tensile stress of the…

A: It is required to choose correct option

Q: A square steel bar is 50 mm on a side and 250 mm long. It is loaded by an axial tensile force of 200…

A: GIVEN DATA- SIDE OF SQUARE a=50mm L=250mm E=200GPa P=200KN POISSON RATIO=0.3 WE HAVE TO FIND…

Q: If load P = 22.9 kips, determine the normal force in bar (1). D P P A 6 ft 51.9 kips 44.8 kips 27.3…

A: Given that, P = 22.9 kips The force in bar (1) is obtained by taking the moment of forces about…

Q: 7. A 20 mm diameter rivet is used to fastened two 25 mm thick plate. If the shearing stress of rivet…

Q: Two forces , each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is…

A: To find : determine the largest allowable value of P. Given :- diameter of shaft ds=30 mm shear…

Q: A rectangular 30 mm x 25mm bar of length 250 mm subjected to axial tension load of 75 kN. Determine…

A: As per our guidelines we have to answer only one question. So, post the question seperately and…

Q: 1 J A cylindrical specimen of steel having a diameter of 14.36 mm and length of 209 mm is deformed…

Q: 28. A 300 mm rod is subjected to 4 kN of tensile force. The allowable stress and deformation is 60…

Q: A rod of length 40 mm is stretched to make a rod of length 60 mm. It is compressed to make a rod of…

Q: 1. Define the terms load , stress and strain. Discuss the various types of stresses and strain. 2.…

Q: 40. A tensile test specimen has a gage length 2.0 in and diameter 0.875 in. Yielding occurs at a…

Q: A tensile stress is to be applied along the long axis of a cylindrical steel rod that has a diameter…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

mechanics of deformable bodies
please solve the problem asap. thankyou

4. A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630 in steel wire,
which is 10 inches long? Assume deformation to be vertical. Use E = 30 x 10® psi.
4.5 in
2 in.
Steel
wire
а.
0.0481
с.
0.0581
b. 0.0531
d. 0.0631
P.

Branch of science that deals with the stationary and moving bodies under the influence of forces.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
A steel bar, the material of which is S355 J2 G3, binds two walls together. Pre-tensioning in tie bar 4.3 kN. The temperature of the rod increases by 15 °C. Calculate the normal stress in the cross section of the bar. L = 600 mm, α = 12μ 1/°C, E = 200 GPa and d = 25 mm . Give the answer in MPa as a whole number as a numerical value only. Correct answer to exercise should be = -27
If d=40 mm, L=796 mm, F=29 kN, T=1.7 kNm and fail stress=156 MPa, calculate the apparent factor of safety for this loading condition. Give your answer to 2 decimal places.
In a tensile test on a steel tube of external diameter 18 mm and internal diameter 12 mm, an axial pull of 2 kN produces stretch of 6.72x 10^-3 mm in a length of 100 mm and a lateral contraction of 3.62x10^-4mm in outer diameter. Calculate the values of three modulus and Poisson's ratio of the material
A spherical tank contains an internal pressure of 3.0 MPa, the diameter is 16 m, the yield stress is 490 MPa. and the factor of safety is 2.5. Determine the required thickness I to the nearest millimeter.
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
See the set of bars for made of a material that has a yield strength of 350 MPa, determine the minimum h1 and h2 dimensions required. Apply a safety factor F.S. = 1.5 without flow. Each bar is 12 mm thick
Q // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined model
A mild steel rod having a stress of 50 Mpa and having a diameter of 20 mm What is the force applied on it.
A hollow cylindrical rod with a diameter of mm and a thickness of mm is under a tensile load of 12.5 kN. Find the smallest material thickness according to the given parameters. The yield strength = 450 MPa, tensile strength = 520 MPa and the factor of safety is 2. N=21
The load on a helical spring is 1282 lb and the corresponding deflection is to be 3.4 inches. Rigidity modulus is 11 x 106 psi and the maximum intensity of safe torsional stress is 60,000 psi. If the wire diameter and the mean diameter are 0.5 in. and 3 in., respectively. Determine the number of active coils. Don't round your answer to preferred size. Round your answer to 4 significant figures