4. Find Norton equivalent circuit across a and b terminals in the given circuit? 14 V 14 Ω 1A 6Ω 3 A ( ЗА 50 ob 5. A series circuit with a resistor of 100 Q capacitor of 25 µF and inductance of 0.15 H is connected across 220-V, 60-Hz supply. Calculate (i) current (ii) power and (iii) power factor in the circuit. ww ww

4. Find Norton equivalent circuit across a and b terminals in the given circuit? 14 V 14 Ω 1A 6Ω 3 A ( ЗА 50 ob 5. A series circuit with a resistor of 100 Q capacitor of 25 µF and inductance of 0.15 H is connected across 220-V, 60-Hz supply. Calculate (i) current (ii) power and (iii) power factor in the circuit. ww ww

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.17MCQ: Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A....

See similar textbooks

Similar questions

InclassofENG100youwereaskedtoconnectacoilofresistance50Ωand inductance0.318Hwithacircuitcomprisinga75Ωresistorinserieswitha 159µFcapacitor.Andyouconnectedyourresultingcircuittoa240v,50HzAC supply. Calculate: (a)the supply current of your circuit; EV(7) (b)the circuit impedance, resistance and reactance; CR(7) (c)the phase angle of the resulting current,use (sine) as your reference and explain your result. AN(6) Question2
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
InclassofENG100youwereaskedtoconnectacoilofresistance50Ωand inductance0.318Hwithacircuitcomprisinga75Ωresistorinserieswitha 159μFcapacitor.Andyouconnectedyourresultingcircuittoa240v,50HzAC supply.Calculate:(a)thesupplycurentofyourcircuit;(b)the circuit impedance,resistance and reactance(c)the phase-angle ofthe resulting curent,use sine as yourreference and explainyourresult.
A 60Hz sourcewith an effective voltage of 240 volts supplies 4500 volt-amp to a load with a p.f. of 0.75 lagging. Determine the parallel capacitance required to improve the power factor to: a) 0.9 lagging and b) 0.9 leading. What per cent reduction in line current resulted in part (a)?
An impedance coil is connected in series with a fixed resistor, and a 120-V, 50-cyclesource is then impressed across the combination. If the voltage drops across the coil andthe fixed resistor are 70 and 80 V, respectively, when the circuit current is 1.4 A, calculatethe resistance and inductance of the impedance coil.
A ower system is operating at 1000Mw, 132kV, 50Hz, with 0.8 p.f. laging in parallelwith another line at 750OMW, 132kV, 50Hz with 0.707 p.f. lagging. Both are interconnectedat the station and when the compensating device is on, the overall power factor isimproved to 0.9 lagging. Suggest suitable capacitors, shunt and series. Individual loadsand combined load are to improve power factor to 0.9 in all cases.
Discuss the role of FACTS (Flexible Alternating Current Transmission Systems) devices in power system control and optimization.
(a) Calculate the equivalent impedance of the circuit given below, if the source voltage is v(t) = 60cos1000t (b) Calculate the source current flowing in the circuit (c) Draw the phasor diagram of the current and input voltage
A) the current supplied by the source B) the impedance seen at the supply (HV side) C) the power dissipated by the tube D) the operating power factor of the fitting E) using a scale phaser, prove your answers and evaluate each technique for determining circuit power factor.
α=4 β=4For the adjacent circuit, Vab=(400+5β)V is given and the source part is balanced. Since it is known as ZAN=j2α Ω, ZBN= 3α Ω and ZCN=-j3α Ω, calculate the value of the current Ib by its angle, ignoring the impedances of the transmission lines.Can you please post your solutions, it's very important
Solve the complex power delivered by each source and show that that total is equal to the complex power absorbed by all passive elements (R, L and C) in the circuit. -Complex power delivered by the voltage source: -Complex power delivered by the current source: -Total complex power delivered by the sources: -Power absorbed by: 10ohm, j20ohm, j10ohm, -j5ohm, 20ohm  -Total power absorbed by R, L and C:
An industrial load of200KW has a powerfactor of 0.5 lagging. Agroup of synchronousmotors operating at apower factor of 0.8leading is installed andthe over-all power factorimproves to 0.75 lagging.Determine the KVArating of the synchronousmotors installed.Answer = 130.2354 KVA