4. Which one of the following statement is correct. a) AC bridge circuit can convert electrical parameters into voltage. b) The resistance of the strain gauge decreases when it is compressed. c) The output of the potentiometer is resistance with the external power supply. d) When total distance increase, the capacitance of the capacitor sensor will increase.

4. Which one of the following statement is correct. a) AC bridge circuit can convert electrical parameters into voltage. b) The resistance of the strain gauge decreases when it is compressed. c) The output of the potentiometer is resistance with the external power supply. d) When total distance increase, the capacitance of the capacitor sensor will increase.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter12: Batteries And Other Sources Of Electricity

Section: Chapter Questions

Problem 3PA: An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80...

See similar textbooks

Similar questions

An office building uses a bank of 63 lead-acid cells connected in series with a capacity of 80 amp-hours each to provide battery backup for their computers. The lead-acid cells are to be replaced with nickel-metal hydride cells with a capacity of 40 amp-hours each. How many nickel-metal hydride cells will be required to replace the lead-acid cells and how should they be connected?
The rotary potentiometer widely used to measure the angular displacement. It has maximum angle of 120 degree and the total resistance of 420 ohms with 30V of dc power supply. If so, calculate the output voltage for the angular movement of 315 degree to 380.5 degree.
The rotary potentiometer widely used to measure the angular displacement. It has maximum angle of 120 degree and the total resistance of 420 ohms with 30V of dc power supply. The error is 0.75 ohms during the measurement of 60 ohms, then calculate % accuracy of the device.
Assume Vs = 25 V, Rin = 600 kΩ, and the voltmeter error rate = 4%. Compute the Rs.
1. Problem statements of the circuit to be designed
Find the missing values given the following information. R1= 1, R2=6, R3=6, R4=1, R5=2, R6=3, Vtotal=50 V
High Voltage Engineering Problem A sample of viscoelastic polymer insulation has intrinsic breakdown strength of 2MV/cm, has modulus of elasticity of 0.01 MPa. dielectric constant (relative permittivity) of 3.2 and thickness of 5mm Find out the possibility of electro- mechanical breakdown.
Please answer with brief explanation..and all subpart for like asap please.. 1) Voltage-level shifters are only needed when the voltage supply levels of the MCU and the peripheral(s) are at different level of voltages. i. True ii. False 2) LCD displays are constructed with two polarizing filters oriented in the same direction to allow the backlight to pass through. i. True ii. False 3) An active-matrix LCD displays incorporates a switching element into each individual cell via the: i. PNP transistor ii. Schmitt-trigger buffer iii. Thin filmed transistor iv. Bipolar capacitor.
Companies designs, creates, and sells Integrated Circuits (chips). What do your buyers useto compare your IC products against your competition’s? Give 3 types of IC benchmarkmeasurements in short answer
Sketch and describe the construction of a moving-coilammeter and give the principle of operation.A moving-coil instrument gives full-scale deflection with 15 mA and has a resistance of 5 Ω. Calculatethe resistance of the necessary components in orderthat the instrument may be used as: (a) a 2 A ammeter;(b) a 100 V voltmeter
In a power supply using 7812 IC, the electronic device that changes AC to its DC equivalent is diode 7805 IC transformer capacitor
Design a simple circuit for a ceramic heater that has three settings of Low, Medium, and High heat must be accomplished with the use of (not one but) two independent switches! no digital circuitry or thermostat may be incorporated in the design. However, incorporation of a “Fuse” is highly recommended. Each heating element will be transferring its heat using one independent fan.